Having problems with your Vacuums ?

Noisey hoover my hoover has started screaming it still succks well and can be used as normal except it is almost deffening

Answers :

Wish you have posted the model number, but the fan on alot of the Hoovers are on the end of the motor, opposite the motor shaft. You will have to pull the motor out to see the fan, if broken, replace it by taking the 4 screws out and removing the fan housing, There will either ne a bolt to remove, or the fan will unscrew by turning clock wise. Sometimes they are tough to get off.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Noisey hoover my hoover has started screaming it still succks well and can be used as normal except it is almost deffening

Wish you have posted the model number, but the fan on alot of the Hoovers are on the end of the motor, opposite the motor shaft. You will have to pull the motor out to see the fan, if broken, replace it by taking the 4 screws out and removing the fa ... Vacuums

Burned smell hi, I have used my hoover 4 times and is starting to smell as something burned, I checked the troobleshouting part of the owner manual and it says that check the belt, I already did that and everything is ok I used the hoover again and still smelling bad and start to work very slow I better shut off it.. what could I do??

If the motor slowed down this would indicate a bad motor. not cost effective on this model to replace unless under warranty. it is not uncommon these days to see a motor go bad every now and then.\015\012\015\012What are the first 4 digit ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

My Hoover Windtunnel Ultra U6425-900 began shutting off after a few minutes of vacuuming. The time interval became shorter and shorter. If I leave it sit a while, it will start again. This does not happen when I used the attachments - only with the floor brushes. The switch has recently been replaced and the whole vacuum serviced by a Hoover dealer about a year ago. I have been told by a local repair shop(not a Hoover dealer) that it is the motor, there is nothing to do other than replace t

... Hoover Vacuums

My Dyson DC07 vacuum started to run slower after being on for a little while and then would run normally again. I have switched on today and it has just stopped. When I push the start button, on occasions it almost starts and then doesn't. I am wondering if there is a problem with the switch and if so how can it be fixed? Thankyou.

The motor running slower was the motor starting to burn out. The "almost start" is the brushes making intermittent contact with the armature in the motor. \015\012\015\012Your machine needs a new motor Pam. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Hoover Windtunnel 2 upright vvacum cleaner. During regular use my wife turned it on and it staarted cleaning, then all of a sudden it stopped and then started again then stopped for good. I unclugged the hose, cleane4de the brushes , blew the main filer and still cannot get it to start. The motor seemed hotter than usual. Can you help me? Lenny Rentz e-mail [email protected]

Actually, if you don't have continuity, then you have an open, not a short. ... Vacuums

Oreck Belts Why do they smell badly and almost always break when being used for an extended period? I see Mr. Oreck in print, television and internet ads -- and he certainly carries himself as a credible person; a man you want to believe....But reading his biblliography -- he started his career (in this area as I know it) as a "Vacuum Cleaner Salesperson" for Whirlpool. Many vacuums brands - particularly those that are noit sold directly by retailers (Oreck, Kirby and others) use the commission-

Unfortunately this is a very common problem on the Oreck XL uprights. As you you noticed, there is even an extra belt storage on the machine itself, on the bottom plate. When a vacuum cleaner has to put an extra belt on the machine ... Oreck XL2200 Bagged Upright Vacuum

Shark/cordless /sweeper - over four years old. Started - but seemed like it was caught and shut off almost immediately. Not used year around - tried to start after absence. I have removed some hair and perhaps dental floss. Checked belt - it seems O.K. Do I need a new battery or is it just worn out.

Check the brush,is there any dirt got stuck in between brush rolls.If there is then it needs to be cleaned.Your cordless sweeper will automatically shut off if an obstruction is caught in the brush roll. the other thing to checks is dust contai ... Vacuums

I have a Hoover windtunnel T series. Model #UH70105. The system check indicator was almost red so I cleaned the filter. There are no clogs and it vacuums fine without the hose, but when I go to use the hose there is very little suction and all the vacuum dust flys out of the end the hose piece fits into when not in use. Can you please tell me what is wrong?

... Hoover Vacuums

Hoover windtunnel will not start i used it for a while tell i switched electrical sockets now it wont stArt

... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Hoover, Steam spin scrub, Model F5897-900. Only used it a couple times and the motor gave out. First started being noisy then a bad smell. It did seem noisier that what I would expect from the start but I didn't realize it was a problem with the shaft of the motor. I took it apart and found the motor shaft wasn't true and causing sparks. The motor looks like it can not be taken apart and repaired. This seems like a default from the beginning but it is past warranty. Also noti

You will have to replace the motor and the hose asm. thehooverstore.com may be able to help, or you should be able to find a repair shop that can order them for you. ... Vacuums

How do you start using the F5815 Hoover Steamvac? I can not find the direction manual.

This link should helphttp://www.fixya.com/search.aspx?cstm=0&_s=F5815+Hoover+Steamvac+ManualJim ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

One of the pins on the plug on my hoover have snapped off, the top one. so i cut it off & tried to use a normal plug but it has blew the electrics. Is there any way round this? Thanks

If you connected all the wires the correct way to the plug then you could have a short in the wiring in the hoover. Get an engineer to check it out. ... Vacuums

Lost suction Been using hoover steamvac today, worked great for the fist 2 hours, got ready to start back at it, and it has lost suction, have tried and tried the water tank repositioning, and nothing seems to work.

There is a screen by the brush that may be clogged. Make sure the water tank is on tight ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Hi, I have a Sebo X4 which is almost 3 years old. I haven't had any problems with it until the last couple of days when I notice a slight screeching noise when in upright position, coming from the roller mechanism area. If I slightly push the sebo forwards it gets worse, if I tip it back it stops. If I take the roller out and switch on, there is no noise. I have always been careful not to tip the machine forwards when using the hose, but I recently lent it to a friend whose hoover had broken do

I dismantled the top part of the machine from the bottom and there stuck right down in the bowels of the tubes was a piece of card, a dress label! somehow it was only making a noise when the machine was in an upright position. It took a bit of stretc ... Sebo X4 Bagged Upright Vacuum

I'm using a miele xtrapower 2100 and the red warning light is on and the hoover will not start. I have changed the bag but it still won't work, is there something i am not doing right?

... Vacuums

I have a Liftmaster garage door opener and the garage door faces south. Normally the opener works great except at certain times on a sunny day.The sunlight is not directly hitting one of the sensors but the door will comedown as far as half way and then it will go back up and the lights will flash. If I go inside and use the button I can hold it down until the door is fully closed. However, sure is a pain to have to take the car out, go back into the garage, shut the door and then leave the h

Sounds like a problem with a limit switch or something getting in the way of the electric eye that interrupts for safety reasons. \015\012Clean the electric eye transmitter and sensor of debris and cobwebs and make sure the wires are attached properl ... Vacuums

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old

Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

I have a hoover u6660-900, 3 yrs old. The drive support works OK in the forward motion but does not in the reverse motion. I don't mind using a screwdriver, but not sure where to start or look. Your thoughts? wally

Another, truly free web site. ... Hoover U6660-900 WindTunnel Bagless Upright Vacuum

My Miele capricorn has started making an odd noise. It seems like something is blocking the engine. I've turned if off and on, and reset it and it still have the odd, almost loud barking noise. The power nozzle also does not seem to be working. I've checked the connections. Right before this happened I was using the vacuum. I didn't notice anything out of the ordinary until this.

Greetings,\015\012\015\012This is a major problem. The Miele vacuums motor should never make a loud noise, period. The way the motor is designed, it's quiet and should be quiet for the life of the motor. There are two motors on your ... Vacuums

My Hoover T5703 has suddenly stopped working. I was using it, moved it to another room, presssed the start with my foot - and nothing! I have checked that the fuse and electricity socket are both OK.I did knock it over a while ago and am wondering if I have broken a bit of plastic in the foot starter. It doesn't seem to 'click' as firmly as it did, but I cannot see how to take it off to check?

... Hoover Vacuums

I have a 1521 Diamond Jubilee Vaccum cleaner. The last time I used it the motor seemed to slow down and then pick up to normal speed. When I turned it off and then back on, it did not start.

... Electrolux Vacuums

We just used our bissell pro heat 25A3/64D9 series and the top half of the handle is not secure. Infact it flies off in my hand as im cleaning the carpet and it almost hit me in the face!!! It just connects to the lower half but there is nothing to keep it secure. If it is not tight the trigger to squirt water doesnt work and I am stopping and starting. It looks like a major design flaw.

I have a replacement pump belt for my Bissell #25A3/64D9\015\012but cannot find the instructions as to how to put a new one on. My son replaced the last belt, and of course he doesn't remember what he did. Is there any way you could please dire ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the

... Dirt Devil M088905 Vision Bagless Upright Vacuum

I have a DC04 which is a number of years old and has started making an awful grinding sound, I'm sure it is the belt which I sprayed with WD40 and this helped for a couple of seconds but as soon as I recline the hoover it makes this noise but not when upright and using the hose. Does anyone have any ideas or how to change the belt? Thanks

You have to change the belt look it up with your local vacuum store. ... Vacuums

Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.

... Hoover U5750-900 WindTunnel Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0958 seconds