Having problems with your Vacuums ?

Hi i hae a star product whipper sniper and i cant get it to go i hae spark i hae fuel but it seems as if there is no fuel getting to cylinder i think it is a problem with my carby the serial no is fcb12071 please help rectify my problem cheers


Answers :

One thing that you can try is to remove the carb from the unit and spray it down with carb cleaner -- maybe it is blocked (?),,, one more thing to try would be to see if it will fire using ether. there could also be something wrong with the fuel diaphram and it is not delivering fuel.
\015\012again -- try the ether and see if it will fire up.
\015\012if you are still having troubles - please feel free to wrote me back here and I will do my best to walk you thru the next steps to fix.
\015\012
\015\012c...
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi i hae a star product whipper sniper and i cant get it to go i hae spark i hae fuel but it seems as if there is no fuel getting to cylinder i think it is a problem with my carby the serial no is fcb12071 please help rectify my problem cheers


One thing that you can try is to remove the carb from the unit and spray it down with carb cleaner -- maybe it is blocked (?),,, one more thing to try would be to see if it will fire using ether. there could also be something wrong with the fuel dia ... Vacuums

I have a vax cylinder model V-094. Working fine then started to play up. Switch it on and the motor seems to struggle to power up. Kind of wurrs up and down. Was thinking it could be the brushes have worn. Tokk to bits and cleaned her up, took a look at motot and brushes, cleaned them too, back together and still them same problem. Help please, hoover is not old but has done some work really don't want to through away something that can be fixed.


Hi.\015\012\015\012after all you have done I would be pretty confident its the motor thats faulty they are expensive to buy so machine is going to be scrap,\015\012\015\012Sorry.\015\012\015\012 ... Vacuums

Ryobi RPBV2500 My blower only seems to ant to run when the choke lever is at the first position. It did run with the choke completely off but seemed to suffer from what I thought was fuel starvation when it ran for awhile. When I took the fuel cap off it would start up again, making me think it had a fuel lock. I had a garden centre with engineers look at it.They said that they had checked the carb and could find no blockages. Can you please help?


... Vacuums

I have a Bernina 930 sewing machine. I read the advice from "dogdanes" about the basting unit seizing up and I think this is my problem. It has happened once before, and I NEVER use the thing, so I think it's frozen. My flywheel won't turn. Can you help me fix this? I have a sewing business and can't afford to have my Bernie in the shop for weeks. Thanks. Maripat


Hi marjpatv,With your Bernina 930 sewing machine where the flywheel won't turn and seems like it's frozen, sounds like it needs some oiling. You may want to try having it oiled first since it could be a possible cause of this issue. You m ... Vacuums

We have a GE Advantium 120 microwave. all sounds like the unit is working all controls work. it does not heat at all. I have the shelds off and do not see any problems. what do you think is the problem and how do I test for it? thank you for your help.


If the unit works but it doesn't heat then the magnetron isn't working. The only way t test it is to measure the 2 voltages that power it: the heating coil - 5 volts AC and the high tension - 5000 volts DC. While you can measure the heating voltage ... GE Vacuums

Hello! Help!! The brushbar on my dyson ball vaccuum will not spin. I took out the brushbar and cleaned it, then reset and cleaned out the filters too but still doesn't work. Do you think I need a new rectifier? Thanks for your help.


Sorry this is not a solution. But after reading your problem and other people with the same problem, i just wanted to say i have a Dyson DC24 ball and have only had it 1 year and the exact same thing has happend it is spotless inside and out includin ... Dyson Ball DC24 Bagless Upright Vacuum

My Domotec Simac PVT2050 Steam Cleaner began to leak to-day. In fact it almost emptied the tank. Can't help thinking it's a simple problem to do with the pressure relief valve but how can it be solved? Thank you. Wendy


... Domotec Vacuums

Power My E Series does not turn on, I have cleaned the filter thinking that was the problem but no results. Help.


Hi Zulydia, \015\012\015\012does that version has the "restore" red button in the upper side?\015\012If yes, when you push it, the engine showld work for litle time only (restoring), then the rest is normal. If not, the engine can b ... Rainbow E series Canister Wet/Dry Vacuum

I have no power, I have changed the plug fuse so this is not the problem and I have cleaned all filters and emptied the cylinder. I have a Dyson DC08 animal (not the upright), can anyone help me?


... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

My vacuum is not sucking theirs a yellow pellet that indicates the air flow. And when i turn it on it moves and i think thats part of the problem i don't know what to do i lost my manuel help.


Try emptying bag. then clean filter. then unblock hose using a broom handle. let us know how it goes. ... Hoover Vacuums

I have a Swan Petmaster 1800w Hepa Filtration hoover s/r no SU3021 and cant find my instruction manuel. Problem is when on hoover it doesnt seem to be sucking anything up?? I have cleaned the cylinder and filters. Is it something to do with the bit that you can use to clear stairs/car etc and not converting back to an upright hoover again? Please help Julie


... Vacuums

NO POWER My Dyson DCO4 Absolute (purple&lime) won't' switch on. I've checked the plug fuse, wall socket and also filters and hoses on machine all seem fine so think the problem is with the on/off button (maybe loose wire or something) but how do i get to it, is there a special way to remove the green on/off button in order to check the connection? Thankyou in advance for the help i am sure you will be able to provide.


The problem is almost certainly a fatigue break in the flex. These usually happen where the flex enters the handle through the rubber sleeve near the on off switch. You will need to cut about four inches off the wire and reconnect it to the switch. ... Vacuums

I sucked up a sock I think its in the hose but I am not sure can you help me slove the problem?


Try using a broom handle and push it out the the same end that it came in. If that doesn't work, straighten a metal coat hanger and make a small hook on the end of it. Reach in and grab it.Good Luck!Jim ... Electrolux Vacuums

My AEG (Electrolux) Business Flexio's (wet & dry) suction suddenly stopped working. I often replaced the bags. Did the motor burn out or is there possibly any other solution to try and rectify this problem? Would be very grateful for your help or suggestions. Kind regards, Anita


... AEG Vacuums

1994 GMC PICKUP 1500 4+4 ,HAVE A PROBLEM WITH IT STARTING IN THE MORNING (RUNS ROUGH) DID REPLACE FUEL INJECTORS BUT DID NOT HELP ,ANY IDEAS?


Also check the fuel filter. This sometimes causes rough idle and even bogging down! ... GMC 1994 1500 PICKUP Front Knee, Driver Side a1z73018 , Driver Side 4

I have a 1937 Johnson 4.2 HP Outboard Motor LT-37 Serial # 273761. The engine is seized and I am looking for info on the best way to free it. I've started by putting marvel mystery oil down the spark plug cylinders. Any hints and help would be appreciated. Thank you. Ron massauto


Do you think it is the engine or the lower unit? If the engine has set up for a long time it may be the lower unit or the prop gearing. Pull the bottom loose at the flange be-careful of any parts you take off and try and turn the engine then. If it s ... Vacuums

Hello, I just bought a Bissell Powergroom (model 92L3-W) vacuum and a Bissell Proheat Pet (model 8910-3) deep cleaner and I love them both. My problem is, when we unpacked them we somehow lost the manuals; I think I had too many helpers that night – they may have gone out to the trash with the boxes. I need replacement manuals if you would be so kind as to help me out. Could you email me a manual for each of these two machines, or tell me exactly where to find them online? I’ve been looking, but


Follow the link below and enter the model numbers to access the User's Guides.\015\012http://www.bissell.com/customer-support/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

Lost Suction This is my second hoover steamvac and i am having the same problem with my new one as i did with the old one that i tossed out. I have used it about 12 times and it worked great the first 6 times... Now i'll empty a full tank of water and only half will get sucked back up. I have tried taking it apart and cleaning and also the rubber seal had some gaps so i sealed those thinking that it was leaking air from there...can anyone help? I am so close to chucking this one and buying somet


Usually when there is no suction, one cause is the lid to the recovery tank is not on all of the way in the back. Also if you have that foam filter on the underneath side of the recovery tank lid, it needs to have a 1/4 in or so gap from the top of ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Good day, I took off the cover on a proheat upright, to install the suction diverter flap. Guy at the shop told me I had to do this but I don't think it was really necessary. Anyway, I am having a real job getting the cover back on. The shampoo mix piston seems to be causing the problem seating the two halves correctly. I see no obvious "right: way to put the piston back in. can anybody help me. Thanks Richard


Hey Richard. Turn the shampoo mix dial so the spiral is all the way at the top when you are looking at it from underneath. then, you want the piston to seat in the top groove of the knob. You want the piston's end that jets out to fit in the space ... Vacuums

Moto Brushes Problem... Who could help?


Where can i fine moter brushes for my ridgid 5.25 hp 16 gal. wet dry vac. ... Ridgid 9 Gallon Wet/Dry Shop Vac 96882 Canister Vacuum

Dear sir, i needs a solution for chinese nokia 6300 mobile's white screen problems so help me how i can solve this problems please.......... fast help me sir. thank you


Remove the memory card and battery replace batterry after 30 minutes to hard reset. If the phone boots up then check card for errors, virus, delete, format as required and reset.\012If this wont solve , you will need help fromNokia care to rein ... Vacuums

We have an Epic6500. when we plug it in the machine works without the hose. We even purchased a new hose thinking there was a problem with the hose. However as soon as we put the hose on the machine the machine does not work. What do you think the problem may be?


Wow, this is a good one. I wonder if anyone has wrked on this machine before. Do you remember what happened when it stopped working / Obviously there is a foul up in the wiring. I need more info. When the machine is on does it shut off as soon as the ... Electrolux Epic 6500 Vacuum

The problem is that the cleaner is heavy to use and does not pull itself forward as it should. It has been back to the supplier 3 times but they have not fixed the problem. The LED's on the front flicker and I think it may be a problem with the sensor. If you have any info. on how the sensor works and where it is located it would be useful as well as any other suggestions to fix the problem please.


If it heavy then do some muscle work and body building ... Vacuums

I havea Bissell ProHeat Model 7901. My problem is that the brush doesn't rotate. I have removed the access cover and both belts and found that the central cylinder for both belts is frozen and will not turn easily. Both belts are fine, except they are now burnt from this cylinder not being able to rotate. What I need is how do I remove the top cover to get at this cylinder to remove it and free it up?


... Bissell 8910 ProHeat Clear View Upright Vacuum

My Sc-505 hello, can you please help me? i got the Sc-505 from my sister (already used) and she did not give me the user manual. i need help at least with the basics, do you think youcan help me? thank you very much.


Go to the shark company online at http://www.sharkclean.com/cg ... Euro-Pro Shark SC-505 Handheld Steam Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0986 seconds