Having problems with your Vacuums ?

I have a 1/2hp master mechanic door opener. when I close the door it goes the full travel down and then opens back up. i checked the eyes and everything was lined up. do you have any suggestions?


Answers :

Look at the setting for "fully closed". it sounds like yours is set for slightly than the actual opening....So, the door reaches that location, and it thinks it hit an obstruction, which causes the door to open....While you are there, reset the sensitivity settings.
\012
\012What I would do is back off the closed position setting so that the door stops an inch or two off of the ground, then adjust until the door is in the correct closed position...
\012
\012You are correct on the "eyes" (infrared sensors) being lined up, if they were not, the door would not close at all.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a 1/2hp master mechanic door opener. when I close the door it goes the full travel down and then opens back up. i checked the eyes and everything was lined up. do you have any suggestions?


Look at the setting for "fully closed". it sounds like yours is set for slightly than the actual opening....So, the door reaches that location, and it thinks it hit an obstruction, which causes the door to open....While you are there, reset the sensi ... Vacuums

The brush wouldn't work when the selector switch was in carpet mode. Took the power head apart and removed the motor. Everything o.k. in the power head. Checked and found that the neutural wire had pulled out of the connector, the connector was never crimped at the factory. What a day! Took 2 hours and a large pizza to get it done. Neutral wire was in the hose just below the handle. Reconnected the wire and crimped it, put everything back together. It works!!!!


Great. ... Kenmore Vacuums

Hmmm Hi there, I actually had tried everything you mentioned except for the vinegar idea which I'll do when I get back up to my home in Oregon. I checked for pinches, the heater, etc. Water does NOT come out of the accessory tool and only will dispense out of the main area for a second or two..any liquid actually starts filling up the area right behind the nozzles and around the pump instead of OUT of the machine. I checked gaskets, made sure there was a tight seal, and even made sure the little


Check the nozzles to make sure they aren't clogged. Sometimes there is a problem with the flow indicator cap, maybe too tight or not tight enough. Try squeezing the trigger while turning the can one way or the other. If at a certain point it starts ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

My McCulloch whipper snipper was working just fine after finding cracked fuel lines,. Replaced wiht home made lines and worked fine until Sunday and now wont start at all . Checked everything , now think its electrical Would like to kow if there is anyone in Perth who can sort this out


Your local lawn mower repair shop will be able to fix it for you. ... Vacuums

Relief valve opens I have cleaned all filters replaced filters checked all hose line for blockage everything is clear


How full is the bag? ... Kenmore Vacuums

Just got done doing a cleaning and replacing filtrer on my eseries rainbow now when i put everything back it does not want to come on? any suggestions. email [email protected]


It sounds like your water basin safety switch is not geing switched.\012\012Let me know if you need anything els,\012Ralph ... Rainbow E series Canister Wet/Dry Vacuum

The brush roller on my vacuum will not move. I've cleaned it, checked the belt, but when I put the roller back it, it will not move...almost like it is in a locked position. Everything has been done correctly from the book yet, it still does not move. Any help PLEASE?


... Electrolux EL8502 Versatility Bagless Upright Vacuum

I have no suction on my vacuum, I have checked everything, belts are good, and hoses appear to be clear of any blocks, any suggestions


Please give the model number and manufacturer of the vacuum. ... Vacuums

I noticed that the little side brush doesn't turn anymore and the Dirt Dog stops about every minute now so I have to keep turning it back on! I have dismantled the brushes and cleaned everything out but that didn't help at all. It doesn't really come apart any more than that for cleaning. Any suggestions as to where my problems may lie?


... iRobot 1100 Dirt Dog Bagless Robotic Vacuum

DYSON DC05 It just doesnt want to turn on. I switched it off, one minute later I tried to switch it back on and it didnt work. I have washed the filters, checked the tubes and everything seems ok.......any ideas? thank you, Lucie


My friends Dyson DC05 was loosing suction and then it stopped altogether one day. When she took the filters out there was black soot in them so it was obvious that the motor had burnt out. I think this happened because she wasn't cleaning the filters ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

The hose has no suction and shrinks up so that it can't even be put back on the vacuum w/o turning it off. I have checked everything that I can think of and don't see any blockage anywhere. I washed the filter about one month ago and I clear it at least once a week.


Just happened to me. Took everything apart. No blockage in the flexable tubing or connections then I looked down the hard, telescoping tube and saw that it was occluded. Everything's fine and dandy now. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Really LOUD Just recently this vacuum went from the normal everyday vacuum to now sounding louder than my power saws in my workshop. Checked for clogs.. everything is clear.... cleaned it all over and then turned it back on and.... The neighbors thought I was running a saw mill out of my house. HELP!


Its the belt if it is a savvy.Have the same problem ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

Mother has a vax swift 1800 - Bagless. has emptied cylinder but now lid will not go back on - reluctant to force as just plastic - weve checked and rechecked and everything seems to be in the right way - help!


... Vacuums

I have a DC25 that will not pick anything up. It seems to be throwing everything back out somewhere. It only powers on when its not in the upright position. There is also a strange noise when it's turned on. I have taken the whole thing apart and cleaned all of the filters and checked for blockages but it hasn't help.


Hi there,\015\012\015\012Sorry to hear you're having a problem with your DC25. You should be able to resolve the issue by following these simple steps: ... Dyson DC25 All Floors Bagless Upright Vacuum

My hoover elite rewind does not pick up dirt like it should. how do i check for a clog? I can hear it picking stuff up but when I empty the cannister there isn't much in it. today it shut off like it threw a breaker. I let it sit and plugged it back in and it started working again. don't know if the problems are related or not. any suggestions??


Have you cleaned the inside filter? Open the cup hold on to the yellow piece in the center and twist it to unlock (there are arrows on the pieces to show how far to twist). Take the filter out and try to clean as much of the debris off of it. ... Vacuums

HI, I HAVE ELECTROLUX LE(similar to 2000). I HAVE TAKEN IT APART, CLEANED IT, AND PUT BACK TOGETHER. IT SEEMS I GOT THE WIRING WRONG. CAN ANYONE GIVE ME A SIMPLE WIRING DIAGRAM FOR THIS VAC? THIS MODEL HAS NO CONTROL KNOB. IT'S NOT COMPICATED BUT I MUST HAVE CROSSED SOMETHING BECAUSE IT SHORTS OUT NOW. HAVE CHECKED ALMOST EVERYTHING ELSE. THANKS.


... Electrolux UltraLux 2000 Bagged Canister Vacuum

Power on I was cleaning carpets, everything was fine. I cut it off to check on the baby, came back..now it will not cut on?


Hello markswifey92. Check your AC cord & plug. There maybe a wire broken. Be careful of exposed wire. #2 May be a bad power switch. Please inform me of the results and I will provide repair steps. Please include Mgfr, model & serial#. Good lu ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have a Kenmore Progressive Upright Vacuum - Purple, and it worked just fine. I emptied the canister (like always) and put it back in place. I turned on the vacuum to it immediately shutting down (motor) and only the lights come on. There is no movement/noise/suction at all! Any suggestions? I have tried everything. I have no idea why it did this.


Make sure that something didn't fall into the fan assembly in the base when the canister was removed. The motor should have an overload reset switch. Try moving the motor manually (power plug out) to make sure that it isn't bound up. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Hoover steam vac F5915-900 no power. it started and shut off 3 times and then no power. only used once. checked everything. any suggestions? Will not turn on.


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Replaces the belt on dirt devil dynamite pluse model put everything back together started it and it burt the new belt up that fast. I put it around the beater brush and the metal bar I thought it should go around, yet it seemed like there should be something else there to put the belt on. What do you suggest? Do you have picture I could go by?


The metal bar you put it around if the bar itself does not spin it is going to burn the belt up. Every thing that the belt is supposed to go around has to turn or the belt will rub on the piece not moving and brake. ... Vacuums

Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest


I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum

I have the yellow altima vac. for a while now I can not get the darn thing to pick up properly. Or should i say keep it up.. The vac does seem to be getting everything picked up but as soon as you turn it off, you have a mess under the vac.. I have checked for clogks and can't seem to find any.. I have removed the hose, Nothing there.. And yep have removed the yellow thing inside the trash cup.. Is there anything else you could suggest??


If it smells hot, then there's a strain on the motor no doubt about it. Check the suction channel behind the sole plate and remove all of the hoses to check for a clog. It could well be that there is a clog inside the machine after the dust channel f ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I have a Liftmaster garage door opener and the garage door faces south. Normally the opener works great except at certain times on a sunny day.The sunlight is not directly hitting one of the sensors but the door will comedown as far as half way and then it will go back up and the lights will flash. If I go inside and use the button I can hold it down until the door is fully closed. However, sure is a pain to have to take the car out, go back into the garage, shut the door and then leave the h


Sounds like a problem with a limit switch or something getting in the way of the electric eye that interrupts for safety reasons. \015\012Clean the electric eye transmitter and sensor of debris and cobwebs and make sure the wires are attached properl ... Vacuums

I have a eureka airspeed AS1000A I bought it 3 months ago. It worked fine but today it will not power on. I have checked for clogs , checked hoses and tried different outlets any suggestions?


... Vacuums

I have a kirby sentria. vacuumed up my son's headphones and immediately shut if off. took brush off, unwound headphones, put it back together. when i turned it back on, the belt snapped. so i went to vacuum place, got new belt, but when i put it on, with the green arrows lined up, it doesn't have much suction. with the red arrows lined up, it just smells like its burning and i don't want to break another belt! HELP!!


Take the front off the vacuum and check inside both the front portion and the canister for additonal clogs. Sometimes something will get caught in the impellor, causing the motor to overheat. Since there's little suction and the smell, I'd guess th ... Kirby Generation 3 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0650 seconds