Having problems with your Vacuums ?

Sewing machine will not start at all - Vacuums


Answers :

I would check to see if your getting voltage to the foot pedal with a volt meter. Make sure the power cord is not cracked or damaged in any way. Operate the switch and check if you are getting voltage out of the switch to the motor. If you are the motor brushes could be worn and if you are not getting power to the motor the switch could be faulty
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Sewing machine will not start at all - Vacuums


I would check to see if your getting voltage to the foot pedal with a volt meter. Make sure the power cord is not cracked or damaged in any way. Operate the switch and check if you are getting voltage out of the switch to the motor. If you are the mo ... Vacuums

My Singer Izek sewing machine starts and stops and wont sew continuously. When I push down the pedal it sews about 2 inches then stops and light starts flashing, I have to let off of the pedal and push it again, over and over. It did this once before for awhile and then just started sewing right for awhile and now its started it again. I've checked everything.


If it's not the thread and not the pedal then it's definitely a power problem. You need to replace the power cable and then check again the functionality. ... Vacuums

Please please help me! I recently bought an Empisal Celebrity 550 Sewing machine, I've used it maybe 4 times up to now. Yesterday I was sewing with it and everything was working perfectly, today, when I got home, I plugged in the sewing machine and started sewing, just to see that the bottom stitch is completely loose. It's making this loose loops instead of stitches? I didn't change a knob or anything from working with it yesterday to today, so I don't understand how it all of a sudden doesn


... Vacuums

I have Excellence 740. Only started using it yesterday. Pieced I have the Elna Excellence 740 and only yesterday started using it. I pieced several blocks. Took a break. When I started to sew again there was a loud clanking sound. I stopped the machine. Since I had only very minimal training I am at a loss as to what to do. I checked the manual and did not get enough informatio. Is there a service center near Miami, Florida? I do not want to mess around with this lovely machine.


... Vacuums

I have a dirt devil bagless cannister,machine will start and vacuum nicely then shut itself off probably beczause it is over heating and will not start again for at least an hour. Does this machine have a heat sensor and is is fixable?


The vac very likely has a thermostat located near the suction motor that will stop the motor to keep it from burning itself out. These thermostats rarely go bad. You need to look for a blockage starting with the power nozzel (carpet sweeper) all the ... Vacuums

I have a Continental Electric portable sewing machine and I can't get the bobbin to thread into the machine to start sewing. How do I place the bobbin and where does the thread need to go for the need to catch it?


... Continental Vacuums

While using the pin stitch , the machine has started skipping stitches, knocking loudly, the top thread is breaking, sometimes thread knots up on the underneath side. I have cleaned bobbin area, changed needle and bobbin, using quality thread, the last time I used machine worked fine, yesterday when I started sewing I had this mess HELP!


Hi,Please go through the link given bellow to have the resolution to your problem...\015\012http://sewing.about. ... Vacuums

I bought a Tacsew T8700 High Speed Stright Stitch and I should have paid more attention to the 'High Speed'! The motor that came with this industrial machine is a Tacsew Clutch Motor model: RM1878-1H. It is way too fast when starting out and usually breaks the thread. The local company I bought it from told me there was not a user manual for the machine or the motor :P. I've finally gottin the tensions adjudsted but still need to be able to start sewing at a slower speed. Any advice out the


If you are just starting off sewing and don't have good foot control change the motor to a d/c motor they are about $120 and you can turn the speed of the motor up or down ... Vacuums

My Janome Harmony 8100 will occasionally stop and give me a System Error #1 - I cannot find anything about this error. It is a computerized machine with 70 stiches and attachable embroidery hoop. I first started getting this error with the hoop and now get it when I am just sewing. As soon as the needle goes down to the bobbin, I get the error. The machine freezes and the only way to get rid of the error is to turn the machine off. Sometimes I can get the machine going again, but now it wil


... Vacuums

The rubber seal strip inside of the vacuum system on top and on the bottom has started coming off. I was wondering if I could reorder this rubber seal stripping to replace on my system. The model number on my system is #91740. MV 261414/1 is another number that was labeled on the back of machine as well. We ordered it off of QVC and the name of this vacuum system is called, Cook's Essentials's Vacuum Packaging System. Thank you for you time. Look forward to hearing back from you soon.


... Vacuums

I have a multifunction robotic auto vacuum cleaner model number XR210. It doesn't seem to be charging when at the docking station. The light is flashing on the docking station as if it was charging, but then I am getting intermittent noises like the vacuum is about to start up, then it beeps and goes silent again. I have emptied the machine. The display does not read 88 as if there is a malfunction, so I'm really not sure what's wrong with it. If I put the vacuum to the docking station the displ


... Vacuums

My Kenmore sewing machine timing has gotten off. I am sewing a big upholstery project and it starting bunching thread from the bobbin. The thread is so heavy that I had to put some pressure just to get it undone. This happen a few times and then I found it wasn't sewing at all. When I evaluated without the materials in place I could see the needle would catch on the white plastic piece under the bobbin and the thread would not catch on the metal arm. It appears to be off by 1/4 - 3/8 inch.


HelloDisassemble your bobbin case which is realy quite easy, clean\015\012thoroughly with a brush and air, paying particular attention to any\015\012rust that may have formed, and any thread that may have weazeled it's\015\012way into sma ... Kenmore Vacuums

The vacuum won't start. I used it for about an hour and then turned it off and when I went to turn it back on ..there was no response. I cleaned every compartment on the machine and it's still not working. I also tried using a different outlet in the house. I've waited 24 hours thinking maybe it might have been just the vacuum over heating, but it's still not working.


I had the same problem and after removing the large round filter and cleaning it, (waiting 12 hrs to dry) it started.... ... Dyson DC07 Bagless Upright Cyclonic Vacuum

How do I raise and lower the feed dogs in the sears kenmore sewing machine model 3851960180. also, my material goes into the feed dogs when I start to sew a seam. Please help! Thanks


... Vacuums

I have an Eureka Express canister vacuum - I believe it's model 8284 - that just stopped working. Plug it in, turn it on, and absolutely nothing happens. I took it to the local sew and vac place and they say it's a circuit board that is no longer available. I've looked at all the parts lists and diagrams for that vacuum and I would swear there isn't a circuit board there. (I wouldn't have even thought that in 1989 they would have used circuits.) In any case, I absolutely love this machine a


Given the age of the machine weighed against you fondness for it, unless you can find a fault with either the switch or the cord, there is little else that can be done. With time the electrical lead can break down and one o ... Electrolux Vacuums

DAS ducted vacuum. The machine starts up, but no suction at inlet. inlet at central vacuum system operates fine.


You either have a clogged line or, your tubing joints aren't sealed. ... Vacuums

I have a Janome DC2007LE sewing machine. I am trying to do a regular buttonhole. I have the correct foot on and the buttonhole lever down inbetween the gap. I also have my button in the back to make the correct size buttonhole. When I start to sew it will make the front bartack and then only a few stitches into the left row. Then it beeps three times quickly and shows bL in the screen. I can't find what that means. and don't know what I'm doing wrong. It is doing this with both square an


... Vacuums

Was sewing on my Babylock Companion 7500 sewing machine when it started sounding like a "rod" was knocking. An alarm sounds, it stops and thread is bunched up on the under side? Got any ideas what the problem might be?


... Vacuums

I have a janome BCC-30 sewing machine and the upper thread has started to break and fly out of the needle while I am sewing. The problem continues even when I change the tension dial.


... Vacuums

Have a rexair model D series vacuum cleaner that worked fine until recently. Started making noise and then started smoking/overheating. I took apart the machine cover and am unsure how to get it tore down to see the motor or belt in there. Please help!


Below I have listed a link to the manual that has instructions on how to change your belt and a link for the replacement belt you need. ... Vacuums

We have the Kenmore progressive direct drive (bagless) and have had it for about 3 years. We have taken good care of it, and paid quite a bit for it hoping that it would last for a good long time. It has started making a noise that seems to be an overflow air type of noise coming out of a bottom air outlet opening for when the air flow is blocked. We have looked into clogs, changed filters, and the whole works, to no avail! Quite Frustrating since I love this purple vacuum! The machine started


There has to be a clog or block somewhere - if the motor works, it should work did you try a wire coat hanger to go up in further where you cannot see?Bets regardsCk ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Dyson animal won't start. Never had any problem with this vacuum. No apparent problem. No electrical problem with house or outlet. If there are some common things I could check/fix, things that might go wrong, I would like to check them out and get this machine going again.


Hi there, if the machine was running and cut out in use, this could be due to the motor overheating. The cause of this would be a blockage or a dirty filter. These checks can be found in the Support section on our website at www.dyson.com. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

1926 singer sewing machine manual - Vacuums


... Vacuums

I have a 9 year old dco5 absolute, and have been vacuuming a lot after renovations, including small amount of fine timber dust. I cannot start it at all, even the next day. Any ideas. I think the motor may have burnt out? There were no smells from the machine Thanks


Yes your right motor burnt out. They can be replaced as I work for company who repaired vacuums. Try godfreys or some electric shop. ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

John lewis mini sewing machine manual - Vacuums


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0974 seconds