Having problems with your Vacuums ?

Replaces the belt on dirt devil dynamite pluse model put everything back together started it and it burt the new belt up that fast. I put it around the beater brush and the metal bar I thought it should go around, yet it seemed like there should be something else there to put the belt on. What do you suggest? Do you have picture I could go by?

Answers :

The metal bar you put it around if the bar itself does not spin it is going to burn the belt up. Every thing that the belt is supposed to go around has to turn or the belt will rub on the piece not moving and brake.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Replaces the belt on dirt devil dynamite pluse model put everything back together started it and it burt the new belt up that fast. I put it around the beater brush and the metal bar I thought it should go around, yet it seemed like there should be something else there to put the belt on. What do you suggest? Do you have picture I could go by?

The metal bar you put it around if the bar itself does not spin it is going to burn the belt up. Every thing that the belt is supposed to go around has to turn or the belt will rub on the piece not moving and brake. ... Vacuums

Burns up belts quickly. Seems like when you put

... Sharp Twin Energy EC-T2840 Bagged Upright Vacuum

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...

The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc

... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

My husband sucked up part of a rug. The belt didn't shut off like I thought it was supposed to. Now there is a funny loud hum when the brush is running. There are also some fuzzy disc-like things around the brush that look like they're unraveling. Thoughts???

See if you can take the brush assembly off. There should be a plate and 2 screws. One on each side. You can lift out the brush and get all of the strings and such off of the roller brush. You might have to go a little deeper with it open and see if a ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

We have already spent $60 on getting the belt repaired once. This time, the same thing is happening, the belt is jumping of the small metal bar in the back of the housing. Seems like there should be something on the end of the bar to keep the belt on it?

Greetings from GoVacuum,\015\012\015\012Ahh, the Hoover Windtunnel Self-Propelled model. This model has a some reoccurring problems with it. The majority of them have to do with the b ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Belt problem My belt broke. I put a new belt in, followed the instructions, seemed to be right but as I started using the vaccuum, it starting smelling like burnt rubber. The belt was extremely hot. Took it apart, tried again and the same thing happened. Please help me!!!!

Get the old lady to use a dustpan and brush instead SORTED ... Kirby Generation 3 Bagged Upright Vacuum

I have a Eureka 4800 series the Boss upright with a bag and Hepa filter. I love it! I was just vacuuming with the hose part and all was well and then suddenly the lower brush came on and a "burning" smell followed. Thought it was the belt so my husband was going to put on the new belt which I had on hand! When he turned it over, the "bar" that holds the belt looks as though it "shot through" the plastic side of the housing on the vacuum. There is melted plastic on the outside of the vacuum and o

I had the same problem. Take out the old belt if possible. Remove the 4 screws inside the filter and the 3 on the front of that housing. pull out the foam around the motor. carefully pull out the suction tube that is press fit against the motor. ... Eureka 4874 Bagged Upright Vacuum

The vacuum turns on but wont run smells like burning rubber I took the bottom off and the belts dont appear to be broken but the one connected to beater bar seems like it may be loose

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=542493\015\012Generic problem for all Vacuums\015\012The vacuum turns on but\015\012Posted by mmetcalf on Apr 24 ... Vacuums

I thought I was buying a manual. I put a new belt on my vacumn but it makes a funny noise and does not leave vacumn lines on the carpet like it used. I don't know if it takes two belts or one.Wish I had a manual.

Hi Frrank: The Owner's Manual for the Euro-Pro Infinity NV31N Vacuum can be downloaded in PDF from the following site:http://dl.owneriq.net/d/df ... Euro-Pro NV31 Infinity Vacuum

I just used my Bissell Proheat, when I heard the vacuum sound get lower and lower then suddenly something "gave" and it got very loud and started emitting a burnt rubber smell. It still worked to put liquid into the carpet; seemed to have trouble getting it out. I checked the tank, filters, belt, and roller and all seemed OK - but when I started up again and looked down I saw sparks in the motor/belt area and shut it down immediately. Any thoughts?

The bearing that is located at the top of the vacuum motor has failed . Because of that the shaft of the motor's rotor is out of position and the pulley attached to it has started rubbing on the other pulleys, giving you that smell. the spark appear ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

My beater bar on my Kenmore 116.25615506 canister vacuum keeps turning on and off when I vacuum rugs. The suction continues, but the beater bar seems to be shorting or whatever. I checked the belts and they look like new. Any suggestions? The rest of the vacuum works fine!

... Kenmore 25512/ 25513 Progressive Canister Vacuum

Shark/cordless /sweeper - over four years old. Started - but seemed like it was caught and shut off almost immediately. Not used year around - tried to start after absence. I have removed some hair and perhaps dental floss. Checked belt - it seems O.K. Do I need a new battery or is it just worn out.

Check the brush,is there any dirt got stuck in between brush rolls.If there is then it needs to be cleaned.Your cordless sweeper will automatically shut off if an obstruction is caught in the brush roll. the other thing to checks is dust contai ... Vacuums

Beater bar The beater bar will not work. I have changed the belt and there is a lot of suction from the hose. Just seems like the base is not turning on

You may have a bad switch, one part of it is not turning on the brush roll motor. It could also be the brush roll motor. ... Clarke CombiVac 12 Bagged Upright Vacuum

Hi, I have a cleanview bagless model# 3576-2 and my belt keeps breaking (it seems like one of the rings it should wrap around is missing) right now I have been wrapping it around the brush and a metal rod. Also, the dirt collected is going directly into the hose and not the bagless filter. What is going on?

... Bissell 3576 CleanView II Bagless Upright Vacuum

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n

From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums

Dirt devil vacuum cleaner--trouble vacuuming dirt and pet hair on carpeting --is the problem with the spinning brush which contacts the floor,  not contacting the carpeting??  I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting.  Sometimes, it seems like nothing is being vacuumed up --unless I have just put a new bag on the vacuum... Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums

Try replacing the belt. Rubber belts stretch out after about a year. ... Dirt Devil CE6100 Featherlite Upright Vacuum

We have a new hoover bagless that is a couple months old. The pet hair attachment stopped working. I disassembled it found lots of hair wound around the various rollers and removed - painstakingly thorough i might add. Problem is the brush still wont spin and now the belt seems loose - I think I put it all back together correctly but wondering if there is a trick to this?

Without the model number, I can't look it up, but this has a 1 years warranty on it, maybe take it to a warranty shop. Just take proof of purchase, model and serial numbers. ... Vacuums

I bought a Dyson Vaccum for pets. Spent around 700 for it, and thought it was the cats meow. They promise that there is no lose of suction, and oh boy is that a joke. I clean the filter that they say they don't have, which they do. I have cleaned it up thinking I just have a dirty vaccum. Now the hose sucks together so hard that it is pretty flat. And the plug in is EXTREMELY HOT!!! It seems like the littlest things fall off of it, and it is all plastic and it cracks and pieces break off.f I don

Sure, we have Miele machines that are German made and excellent with 10 year warranties we are also a dyson repair center for warranty.\015\012Dyson Repair Form ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My roller bar doesn't seem to be working, but I checked the belt and it appears to be fine, but a bit loose. Is this the problem? dial on front to determine heighth is also very loose and does not click anymore like it did a few months ago. Any help would be appreciated. thx.

If the brush roller stalls when it comes into contact withthe carpet, it might be that the tensioner spring has broken off. This is adesign flaw in the Eureka4870. The symptoms are: 1) brush spins until it contacts the carpet then itstalls, 2) the br ... Eureka Smartvac 4870 Bagged Upright Vacuum

When using my hoover wind tunnel the last few times it has emitted a burnt rubber smell so my husband checked the belt and is wasn't broken or off but now when I use the vacuum the beater bar doesn't seem to be going around as well as it should be can you help

I take it the belt was put back on !! i would say hubbi forgot the tension arm a little black striker that can go in two ways but put in back wards it will not tension the arm ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

I replaced the belt in our Eureka Boss Smart Vac, it still seems loose, it uses a type R belt. The beater belt still doesn't seem to turn properly and seems that it doesn't pick up very well when I use it on my berber carpet. We have 2 dogs and I like to use it frequently. I have changed the bags and belt......

Check to see that the beater brush is not frozen up. Pull the brush and clean it, spraying some WD40 on each end piece that holds the brush in place.\015\012Also be sure the belt is properly installed so that the brush turns in the correct direction ... Eureka Vacuums

Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn't seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right....can you help. I am v

I've successfully used a compatible belt - Royal 104425001 .It's still new, but for the time being at least - it works. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

My oreck upright smells like rubber burning when i vacuum. i just put a new belt on but it smelled like that before i even put the belt on

... Oreck XL Ultra Bagged Upright Vacuum

My dyson dc07 brush bar seems to be only spinning at half speed. Leaves three light streaks in the vacuum marks like somethings just dragging. Brush bar is clear and filters are clean. Seems like there's slipping somewhere.

The belt is stretch and so it is slipping on the motor shaft. You need to change the belt. Here is a link for the\015\012instructions on how to change the belt and a link for the belt you need: ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1055 seconds