Having problems with your Vacuums ?
Have a Genie 2020L garage door opener. Door start to go down then stop and return. Tried cleaner old sensors. Same. Noticed red light on sensor 3blinks then off....repeat constantly.
Replaced sensors - same issue. Reset unit...checked all wiring...no jams anywhere....
HELP PLEASE L:-)
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Have a Genie 2020L garage door opener. Door start to go down then stop and return. Tried cleaner old sensors. Same. Noticed red light on sensor 3blinks then off....repeat constantly. Replaced sensors - same issue. Reset unit...checked all wiring...no jams anywhere.... HELP PLEASE L:-)
I have a Liftmaster garage door opener and the garage door faces south. Normally the opener works great except at certain times on a sunny day.The sunlight is not directly hitting one of the sensors but the door will comedown as far as half way and then it will go back up and the lights will flash. If I go inside and use the button I can hold it down until the door is fully closed. However, sure is a pain to have to take the car out, go back into the garage, shut the door and then leave the h
Sounds like a problem with a limit switch or something getting in the way of the electric eye that interrupts for safety reasons. \015\012Clean the electric eye transmitter and sensor of debris and cobwebs and make sure the wires are attached properl ... Vacuums
I hit the button and just the light comes on,then i hit the button again and the door closes almost all the way but opens and light keeps flashing . the sensors are on and clear of obstructions . it is a wayne dalton quantum 3212 garage door opener.
Hello ccap..... It sounds like one of those sensors has gotten out of alignment with the other. check to see if there is a steady green light on each sensor. If not, adjust until the light is a steady green. Joe\015\012\015\012Thanks ... Vacuums
Low suction I have a Hoover central vacuum system. I've reset the fuse box, checked the fuses, all of the lines are clear and there are no holes for escaped air to travel out. The filter has been cleaned as well. The vac works well with high suction when hooked directly to the unit, however when using any of the indoor connections there is extremely low suction. The machine still turns on so I do not believe it is an electronic issue. I have troubleshooted the issue as best I could and would
... Hoover L2310 GUV Central System Vacuum
I shorted out the light socket on my Chamberlain Professional Garage Door opener. Now it wont open, I am looking for a fuse or reset button, but cant find one. Is there a way to reset it or did I fry the solinoid
First check your house fuse. ... Vacuums
I have Pro Safe PSF80 and everytime I enter my password, the lights are blinking and can't open the safe. Since the only way to reset my password is when the door opens, I cna't reset it either. I need yuor help, how to fix this problem.
2 blows with a pickaxe on the hinge and it was open in less than 1 minute ... Vacuums
My e wave microwave appears to be in fine working order until the door is opened. It then trips the breaker and ceases working. Ater the house breaker is reset, the power is restored to the microwave until the door is opened again.. I havve tried plugging the microwave into another area that is on a different power breaker but again the breaker trips and the microwave ends all functions. Have you any solutions to my problem? Email Address [email protected]
You may have a short circuit on the INTERIOR LIGHT BULB circuit in your microwave.\015\012\015\012This might explain why the breaker trips every time you open the door.\015\012\015\012If so, you would have to unplug and disass ... Vacuums
Electrolux Epic 6500SR Full Bag sensor working, Does not Reset properly
The problem was a sticking switch that was not being reset. The vacuum on/off switch mechanism is comprised of two switches. One is the main switch that turns the vacuum on and off. The second is a shut off switch that gets tripped when the full b ... Electrolux Epic 6500 Vacuum
I have a THR 138 remote thermometer sensor. It is stuck on HH.H degrees and will not reset. What can I do to fix this? Thanks, Mark Heisler
... Oregon Scientific Vacuums
My electrolux canister model keeps shutting off after a few minutes use. can reset by unplugging and replugging, or by opening and closing access door
... Electrolux Lux 5500 Canister Vacuum
540 Roomba goes in tight circles left and right after backing off charging base - stops and give oh-oh signal and 9 beeps - I have taken off bumper and cleaned sensors etc - blown out with air and still have same issue - unit will also not find or go back onto charging base - any suggestions /
... iRobot Roomba 540 Vacuum
My i-robot 550 will move off of its docking station and then stop and the charging ring will turn red i can then reset it and it will do the same thing. i have cleaned all brushes and sensors.
... iRobot Roomba 550 Vacuum
LOUD Same issue here, I feel like my neighbors from the house next door will hear the vacuum!!! It is sooo loud!
You might need to change the drive belt. Here\015\012is a link to the belt you need and to the manual:Eureka 2961AVZ Belts ... Eureka 2961AVZ Bagless Upright Vacuum
We have just purchased a SX4i and the door chimes keep going off at least 10 times per day. Any ideas what we can do. Have reset etc.
Kenmore Microwave Hood Combination Model #721.80839500 The microwave will not turn off. Even if we unplug to reset it, once we plug it back and close the door it runs constantly.
We understand that your problem is: I currently own and use on a regular basis the Kenmore Progressive upright bagged vacuum. Model number 116.35923500. The headlight flickers and the intelliclean light stays red. Ive tried cleaning the intelliclean sensors, changed the bag, and cleaned off the agitator. Is this a power issue? Should I take it to the store? Any suggestions would be greatly appreciated
Welcome to fixya\012\012Hello\012\012 \012\012I have a solution for this ... Kenmore Progressive 35922 Bagged Upright Vacuum
Need to replace vacuum door - Windsor SR12 Sensor Bagged Upright Vacuum
I pried up the back of the cover holding the height adjustment wheel and was able to snap the cover axle with the cover installed into place. ... Windsor SR12 Sensor Bagged Upright Vacuum
My Shop Vac (Brand) Mdl#934-16-11 keeps shutting off while I'm dry vacuuming. I can turn it back on then it will shut off again. The filter is spotless, so that's not the issue. There isn't any reset buttons. The only thing I can think of is that the float for wet vacuuming is somehow being sucked up causing the the motor to be tripped off. The vacuum is only about a year and a half old and used only sparingly. Help!
I Have a Sharper Image EW400 In/Out door temp. clock. My remote sencor no longer works. How can I replace it? Only info is EW400, FCC ID: N92TTX302 and 08JAN0C Any help to get a remote sensor would be appreciative. Jim
Roomba 4270 stops too soon. my roomba got weird all of a sudden. it started not moving all over as it should. so I tore it all down as I had done before and cleaned all the hair and dirt out of every thing I could without getting down to the basic shell. it does work now and does move all over but stops after about 10 minutes. brand new battery so not a battery issue. could I have plugged some of the sensors in the wrong 'plug'
... iRobot Roomba 560 Robotic Vacuum
I just bought a Hoover Platinum Collection MaxExtract Carpet Cleaner (Model No. F8100900). This is the first time I've used it and got half way through one room and the unit cut off and has no power at all. No lights anywhere. On/Off button is inoperable. I checked the outlet and it's still operating so it's not a circuit breaker issue. The problem appears to be with the machine. Has anyone heard of this happening this quickly? Is there a reset button on the machine>
... Hoover Vacuums
My iRobot Roomba 560 starts spinning sporadically during the cleaning, and after over 3 minutes it complete stops and beeps 9 times. It is necessary to turn it on until it decides to work properly, and keep waiting for the next time the same failure will occur. I tried to reset it, and I have all the dust removed including from the bumper and sensors.
It's the bumper. Blow it out with compressed air and clean the cliff sensors. If you still get the 9-beep error, call support. ... iRobot Roomba 560 Robotic Vacuum
Is there a reset button for the bissell healthy home vacuum cleaner? I was vacuuming and sucked up a door mat and it turned off and will not turn back on
... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue
I have model RGR126 Wireless Rain Monitor. All of a sudden, it has quit registering outside temperature. I changed the battery in the outside sensor and even pushed the reset button, but nothing I have done is fixing the problem. Please help! I really miss getting the temperature outside before I get dressed for work. Thanks.
After a brief power outage my Marantec 4700 garage door opener has problems opening/closing. When opening it stops at the fully open position and the lights blink, when closing it automatically reverses just as it fully closes and then the lights start to blink again. I checked for obstructions and tried to reset the limits of travel per the manual, it still does the same thing. Any ideas on what to try next?
This is not a sensor issue, I have a similar problem, sensors work fine, garage door is still fully functional, all operations, including safety sensors work properly, just the overhead lights flash. I suspect there was damage to the power board due ... Vacuums