Having problems with your Vacuums ?

I have a roomba 551. Have cleaned and removed every bit of dirt and hair off it bu the brush cage won't close when the larger bush is put in. The cage will only click locked on one side, and the other side keeps hitting the brush and won't close. It's almost as if the bursh itself is not even, but this doesn't seem to be the case either. I've even tried removing the yellow rings, but makes no difference. Occasionally it runs fine, but most of the time the roomba just hobbles and clacks as i


Answers :

Hi, had the same problem, it was like the main brush no longer fit into it's slot, so the brush cage would not latch. I discovered that the yellow bearing tip on the main brush twists off, and inside I found a lot of hair twisted around the pin. There was so much hair that it had forced the bearing tip to unscrew, making the brush too long to fit in the slot. After I pulled out the hair, the bearing screwed back on perfectly, and it works great now.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a roomba 551. Have cleaned and removed every bit of dirt and hair off it bu the brush cage won't close when the larger bush is put in. The cage will only click locked on one side, and the other side keeps hitting the brush and won't close. It's almost as if the bursh itself is not even, but this doesn't seem to be the case either. I've even tried removing the yellow rings, but makes no difference. Occasionally it runs fine, but most of the time the roomba just hobbles and clacks as i


Hi, had the same problem, it was like the main brush no longer fit into it's slot, so the brush cage would not latch. I discovered that the yellow bearing tip on the main brush twists off, and inside I found a lot of hair twisted around the pin. Th ... Vacuums

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.


... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

My roomba wont work. Pushing the power button doesnt do anything. It charges seemingly normal, going to green in a few hours. ive tried the reset trick, holding the power button down with the battery removed. Now what? thanks


... iRobot Remanufactured Roomba Vacuum Cleaning Robot with Scheduler, Case/Color May Vary Robotic Vacuum

Trying to set up my new dc24 dyson ball but brush wont come on and ball doesnt move whats up?


... Dyson Ball DC24 Bagless Upright Vacuum

We are trying to replace the belt on the bissell 89q9 model. We purchased belt 8 and got in onto the brush however the brush doesn't spin anymore. Even trying to turn it by hand doesn't work. One end of the brush has a round end to slide in (clear end piece); however the other has a rectangular end to slide in (black end) so we don't even know how it ever turned. Any suggestions?


Remove the beater brush assy & remove the\015\012shaft & brgs that go through it 7 clean out the \015\012hair,fuss ect,so it will turn\015\012\015\012You need to take your vacuum apart once a year or more\015\012to clean ... Vacuums

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a


... Bissell ProHeat Deep Cleaner Upright Vacuum

In the undercarriage where the green cage that is to open when the yellow tabs are pressed will not open. the right side will unlatch but the left one wont unlatch.


... iRobot Roomba 530 Robotic Vacuum

Kenmore vacuum- no suction, brush wont turn


Sounds to me like you have a plugged vacuum. Check all the way through. ... Kenmore 22812 Bagged Canister Vacuum

Kenmore vacuum - no suction, brush wont turn


Sounds like the vacuum is clogged and putting too much stain on the agitator, so I would clean out the entire passage way for the vacuum and replace the agitator belt, you must clean out all the hoses it is clogged somewhere ... Kenmore Vacuums

Roomba 4106 new battery charged but wont start


See the diodes, resistor, capacitor inside for test. since the battery is new, the power charger is faulty, power regulator IC is bad.God bless you ... Roomba 3005 Pro Robotic Vacuum

Roomba Stops I've had a Roomba for about 2 months. Lately, it runs for about 45 secs, then stops, makes a two-tone (descending) sound, and flashes the CLEAN button while the STATUS button is red. I've emptied the dustbin on it. Can you help? I am seeing the same problem on my roomba today. I cleaned all that I could., the brushes, the pins on the sides and all that and it still gives the same problem..Any other fix?


Run your roomba through a self diagnostic test. I have posted the link below. Tell me your findings.\015\012\015\012\015\012http://mysite.verizon.net/gsplews/Diagnositic-Tests_Proc.v.0.5.htm ... iRobot Roomba 4210 Bagless Robotic Vacuum

Keep getting message 'please remove and clean Roomba's brushes'. Have removed and cleaned brushes and even fitted new one's but still getting message. Also brushes sometimes rotate, sometimes not and not picking up very well at all. Help!


Must be your inbox is full, Delete old / unwanted messages. It should resolve the problem ... iRobot Roomba 500 Series Virtual Wall Lighthouse 80201 Robotic Vacuum

Last time I used by Hoover it worked fine, took brushes out to clean them and now when I try to put them back in they won't snap into place and lock. Looks like all tabs on both sides of the brush piece are there and I spin the brushes for the center spindle to line up but it won't snap into place.


Just slightly turn the brush wheel, The tabs look square, but are just a little different in one direction ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Agitator brushes wont turn even after cleaning


The brushes will not turn even wen the switch is turned on ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My roomba 550's side brush cannot move


... iRobot Roomba 550 Vacuum

Brush not spinning even after you press the little button on the side of the brush


Hi there,I'm sorry to hear you're having difficulty resetting your DC24. You might want to take a look at the video below, to make sure you've followed all the steps as we recommend. You may also want to use something like the eraser end of a ... Dyson Ball DC24 Bagless Upright Vacuum

I'm trying to get my S7000 Miele to stand upright an lock in this position. It wont , i tried to see if foot release was jammed but cant tell it doesnt seem to release to let it move upright an lock in again..help


There is a rear dust cover that sometimes gets stuck, this will make it almost impossible to lock the handle up. First locate the cover which is at the rear right above the wheels. It's about 2"x8" and ribbed vertically and slides up behind the rear ... Miele S7210 Bagged Upright Vacuum

No suction I have new belts. Everything is clean. No clogs. When I turn it on it smells like rubber , the brush doesnt spin. Everything seems to be free flowing.. Roller brush isnt stuck on the ends. Took off hose to make sure no clogs anywhere. There is not even suction thru the hose with the handle in upright position.


Generally, the problem is that the belt is not running the brushes.  This is caused by one of the following:\015\012\015\012\015\012beater brush is jammed.  This is either an object stuck in the brush or im ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Roomba is not picking up dirt but does pick up dust. That is, the dust chamber has dust in it but the dirt chamber is empty. The brushes don't have any fluff on them either which is not normal. The fan is blowing out plenty of air, the filter has been cleaned but we suspect the brushes aren't turning. an you help?


... Roomba Vacuums

Our Roomba 530 stops after few minutes saying clean the brush ,even after brushes are cleaned.


FIrst, remove the dust bin part and the brushes. Then, there are four\015\012screws on the bottom gray panel which have to be removed first in order\015\012to get to the gears which hold the brushes. I did not remove the little\015\012sweeper brush o ... iRobot Roomba 530 Robotic Vacuum

My westclox model #22687 was flashing this morning when i got up then it went to steady 12:00 - when i tried to set it - i could not get it to do anything - it's like it's frozen on 12:00 - i even tried to change the battery - but that didn't free it either - what do i do?


... Vacuums

Roomba give message to clean brushes even when I have cleaned brushes, wheels, and anything else I can find. It will only clean about 3 minutes.


Pull 2 roller brushes off.remove funny lookin yellow ends clean hair ect. also pop out front wheel and clean ... iRobot Roomba 560 Robotic Vacuum

Why does our Roomba says there is a problem with the brushes even after they have been thoroughly cleaned? It will run a minute maybe then tell us there is a problem, check brushes.


You need a new battery if you have done the battery reset,and then leave the unit on the charger for 16 hours straight if the problem continues after the charge you need to get a new battery ... Vacuums

Liquid dispense i pulled the brushes out of the bottom to clean by using the releases on each side. NOW i can't get the fluids hose on while trying to put the brushes back in.


Try putting the fluid hoses in first then the brush \015\012"you can only put one pant leg on at a time" ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

My roombas side spinning brush won't spin what do i do and I have already replaced it with a new brush


... iRobot Roomba 560 Robotic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0675 seconds