Having problems with your Vacuums ?

Pentax water pump 1/2 hp when pump starts works well but pump does not cut out when all taps in the house are closed


Answers :

It sounds like the switch is faulty take it back to the shop and tell them ok
Check your toilet tank. Turn off the water going to the tank and see if the pump stops working. If not then the pump is recycling water through the water line.
Gibbs.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Pentax water pump 1/2 hp when pump starts works well but pump does not cut out when all taps in the house are closed


It sounds like the switch is faulty take it back to the shop and tell them ok ... Vacuums

Dyson DC07 My DC07 cuts out after 5 mins and I want to replace the thermal cutout. I have cleaned it thoroughly, including the cyclones but it still cuts out. How does the plastic moulding around the motor dismantle? I have started by removing the 4 torx screws but the upper grey housing does not want to detach and I am worried about breaking the plastic. Appreciate any advice.


Try this page: -http://www.fixya.com/support/t192124-overheating_dyson_dc07Regards Gualo ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My electrolux oxygen canister cuts on and off. I have to open and close the vacuum, or take the base of the hose off and then re-insert. I have to do all these things before it will start up again. I sometimes shake the hose around, then it will come back on. If I try to dust with the dust brush (like a lamp shade or shelf) and the suction pulls against the object, the vacuum goes off for awhile. Sometimes I'll have to reset the vacuum by unplugging the electric cord. I never get to finis


Maybe you should have taken it back to that shop, it appartently isn't fixed. I would have replace that board, don't believe in modifing, you usually end up with other problems, like you have. One thing to check is maybe you have a partial clog in ... Vacuums

I have a modelF5914-900 steamvac cleaner.serial #0704 0011 4711 I cleaned the carpets in my house and then started to do the stairs with the stair attachment. I got down to the last four stairs and the solution would no longer come out. I checked the tank and hose connection and tried priming the pump per the instruction manual. nothing worked. Could you make a suggestion as to what the problem could be? Thank You


Check fuses goin to the pump, is the pump working? if so you may have an air pocket or a air leak in the intake. ... Vacuums

WST 1600A I purchased this vaccum about four months ago from Heartland America. Up to this point it's worked fine. After cleaning it this time when I went to start vaccuming again it runa for about 10 seconds and cuts off. I've changed the battery, taken everything that can be removed out checked it and replaced it. THe motor sounds like it's straining. I have not taken the housing off the motor to see what's going on with that. I misplaced my manual.


It sounds like there is a clog. If there is no air flow it could be overheating. ... Westinghouse WST1600 Upright Vacuum

GE Spacemaker Microwave PVM1870 fan keeps running after door closed and won't shut off. Have to open door or unplug. As soon as door is closed and plug is back in, fan starts up. If door handle is pressed downward, microwave starts! If door handle is raised, fan shuts off but light stays on.


... Vacuums

Alto force 5000 pressure washer Q:- The motor cuts out and will not start again, I try changing fuses etc. Eventually it starts again? but for a short while before it cuts out again.


... Alto Vacuums

Fantom vpw46h,house pressure washer.the motor runs,it was setting for sometime started,using it,but never had any pressure besides the house hose pressure, with the motor running,then the pressure startes to work great,while using it the wand hose came out of the pressure washer,i put it back in,now the motor will only run when i try to adjust the wand head but will not produce any pressure and will shut the motor off,it seem like as soon as the wand hose came out of the presure washer and after


... Vacuums

I have a nearly 9 year old Electrolux Excellio Z5228 vacuum cleaner. It has recently started cutting out during operation. I cleaned the micro filter (between bag & motor) via brush & hitting against wall & seems / looks quite clean. I washed the gore filter (output from motor to clean the exhaust air) as per instructions, then let to dry. It was very clogged but now very clean. The vacuum clearner still cuts out often. Even after a long rest (say overnight) it still won't start, then ano


... Electrolux Vacuums

My garage door opener will start to close then stop and go back to the open position. If I put pressure on the door as it is closing sometimes it will close all the way and sometimes it will return to the open position. Can you help me. Thanks


Sounds like the pressure sensor is being tripped - this is a safety feature on most makes in the last 10 years.Find the make/model of your device and it probably has some knobs on the main unit to adjust. For example, on the ... Vacuums

I have a Chamberlain Liftmaster Professional 1/3 hp garage door opener. I'm unable to find the model number, but it was made in April 2004 and has an orange learn button. It has been working fine since it was new, but now will not open or close when the code is entered on the touch pad. When the problem first started the door would close, but not open. I have tried to reprogram a new digital code, but it does not work at all. There are no problems when opening or closing the door with the re


... Vacuums

Lid won't close. I started to put in a new bag but accidentally took out the plastic insert section the bag should attach to--so when I closed the lid over that, I must have pushed a little too hard. Now it won't com[pletely close! The plastic clasp is intact. Is there anything I can do before having to haul or send it for repair?


Your supposed to take out the plastic part that holds the bag but the way this unit is designed the lid will not close unless everything is inthere correctly so just make sure evverything in inserted correctly and keep trying! DO you still have your ... Electrolux Harmony Canister Vacuum - EL6985 Vacuum

I have a Saeco Armonia Espresso Machine. The water pump was running when the tank ran out of water and when I refilled the tank, it wouldn't start again. I unpugged it and turned everything off overnight. The pump is very loud and won't pump any water.


Common on Armonia...There is no water in the system, so the pump is pumping air!!you have to push on the usual button but make sure the hot water button (for tea for ex) on the right side (same as steam opening valve) of the machine is op ... Saeco Vacuums

Cutting out when the vacuum is upright it is cutting out with what seems like close conection. any thoughts?


Greetings from Govacuum,You may want to check the handle position. On the base of the handle there is a little tab (see picture below) that has open one side, closed on the other. If for some reason the handle is not completely down, th ... Sebo X4 Bagged Upright Vacuum

After a brief power outage my Marantec 4700 garage door opener has problems opening/closing. When opening it stops at the fully open position and the lights blink, when closing it automatically reverses just as it fully closes and then the lights start to blink again. I checked for obstructions and tried to reset the limits of travel per the manual, it still does the same thing. Any ideas on what to try next?


This is not a sensor issue, I have a similar problem, sensors work fine, garage door is still fully functional, all operations, including safety sensors work properly, just the overhead lights flash. I suspect there was damage to the power board due ... Vacuums

My shark steamer has stopped working after a year of having it (I have already replaced one, I'm a idiot!). My problem; however, is that it will steam, but the steam stops traveling through the actual "mop" part. I plugged it in, wait seconds and start pumping, but the steam builds up until it's hard to pump. I had to press the button really hard for the bottom to come off and it shot off like a rocket! I tried to stick something through the tubing, but it did nothing. What am I doing wrong? I


\012\012\012Hi,Here\012is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it\012may not be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I have a 5 yr old Ariens snowblower ( model # 924124). I am having a problem with the deflector cable freezing. I had the deflector cable replaced a yr or 2 ago. I took the cable off and brought it in the house to thaw. When I reinstalled the cable, it worked ine except the shute does not operate in its full range of motion. I have the cable EXACTLY in its original position and routing. The shute only closes about half way. I cannot get the shute to close any lower. Any suggestions?


... Vacuums

Simplicity vacuum My vacuum just cut off and now it wont start. I pressed there restart button but nothing happens I have 2 fairly old Industrial hitachi dry vacuum in my workshop both 110v and both wont start. Both i was told were manufactured in Italy and both have a manual and auto switch. It has a black top, takes an orange paper filter inside and its bin is dark blue. Sorry i've forgotton the model number. I've inspected the wiring but it's fine, could it be the motor and how do i gain acc


Just take it in to your vacuum store. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Won't start. My son was using the vacuum & Didn't change the bag. The vacuum was making the full bag smell, but the light was't on & it didn't stop. I stopped him, changed the bag, checked the filter, closed the compartments & turned on the vacuum. Nothing happened. I checked to be sure that it was plugged in, that wasn't the problem. I've let the vacuum "rest" for several days, It still won't start. Any suggestions?


There is a reset button at the back of the powerhead. The user manual can be downloaded from the electrolux website, although I didn't find it very useful. There was some info on how to change the powerhead drive belt. ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Where can I find a part for my BV2000 in house vac? It is the smallest unit made by M S & S Systems in Dallas TX. The suction impeller is grinding in it's housing, so I need a motor/suction pump. I have removed this combination from inside the vac assembly


You will have to replace the whole motor as these motors where never made to be serviceable. if you take the motor to a local vacuum shop than can order you a new one. though i would recomend replacing the whole tank unit with a Nutone or Hayden they ... M&S Systems BV-2000 Bagged Canister Vacuum

I've replaced the pump and belts. The problem is that I need a drawing or schematic on the routing of the plastic tubing in particular the tubing that comes off the pump and the tubing connection on the suction tube that attaches to the fan housing.


Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Everytime i start my vaccum cleaner it cuts out and than start back a few miutes later


You have a lose wire inside . It may be a bad switch, one or the other. DFD ... Vacuums

My wife and I own 6 IRobots: 1 Scuba 1 Dirt Dog 4 House cleaning vacume models All of them are not working, so I decided to try and solve the problems with two of them: One is a dirt dog and the other a house cleaning vacume Rumba. Given: Battery is fully charged Reaction: I start both of them. They run for about 2 to 3 seconds They come to an abrupt stop as if there is a rock in the gears. Help


Both of them have identical issues? Can you please provide the actual part number of them? It should be on the bottom or inside the battery area somewhere.ThanksTim ... iRobot 1100 Dirt Dog Bagless Robotic Vacuum

My Kirby 2HD has started making an odd roaring noise but still works fine. I have taken the front assembly off and cleaned and adjusted the roller and checked the belt. The noise seems to come from the motor housing. I have tried to wiggle the main shaft at the front (bearings?) and it seems tight. Can't seem to get the other housings apart. Any ideas? Thanks, John


It is quite possible, it just needs lubed. The motor comes in direct contact with dirt so, you have to make sure the front bearing has a drop of oil on it from time to time. If it starts to scream at you within one month, after oiling, the bearing ... Kirby Heritage II Vacuum

The power head of my DC 21 keeps cutting off as soon as I start moving the hose around. The only way to get it going again is to step on the main switch on the canister, then the whole cycle of off and on starts again. I have replaced the entire power head and tested the continuity of all the wires in the hose and they are good. The repair shop says the PCB is bad but can not get one. What can I do ?


Not much. my only suggestion is to dig through the internet and try and find that pcb it may take awhile but it would be worth a shot. if you dont think you can make the repair take it to repair shop with new pcb and let them do it. ... Dyson Genuine DC-21 "Stowaway" Spare HEPA Filter, Dyson
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0366 seconds