Having problems with your Vacuums ?

How will i install a new lightbulb in my house? better if you will send me a diagram. thanks

Answers :

First off all make sure the light swicth is off if there is a light shade around it take is off then hold the light the white light fitting and get hold off the bulb then push up gently and turn the bulb antiy clockwise and it will pop out to replace new bulb off same watts do the same as taking it out but in reverse then put shade back on then try the swicth to see if it turns on if not the bulb is no good try a new on but be gentle with them they brake easy ok hope this helps you
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How will i install a new lightbulb in my house? better if you will send me a diagram. thanks

First off all make sure the light swicth is off if there is a light shade around it take is off then hold the light the white light fitting and get hold off the bulb then push up gently and turn the bulb antiy clockwise and it will pop out to replace ... Vacuums

Jun 24, 2010 - Jun 24, 2010 - Needle not bent/ new needle not answer. I finally conclude that the entire bobbin case is ROTATING in its seat, which jams the needle. The "projection" is against the "spring" when I install it, but I can rotate the bobbin case PAST the spring without trying very hard. Bobbin case MIGHT get held in place better if it were closer to me (front of machine). I feel it is still not out from under needle plate as shown in diagram, but can't keep it closer to f

Hi,Your problem dated 24th June 2010 was re-posted today. If it has been already resolved, kindly ignore this message.Thanks for using FixYa ... Vacuums

Have new oreck quest canister and having trouble figuring out how to change vacuum bag. I have the plastic piece that you attach bag to, but don't know where the piece fits into the vacuum. looking for a diagram or manual to see where to install the plastic piece

... Oreck Vacuums

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o

Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter

There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums

I have a dyson animal dc17 vacuum and it totally died. Now I can't figure out which wires go where when I install my new motor. (motor #: 160906G) Do you happen to know where the various color wires go or a place I can see a diagram of the motor with wires attached? I should have taken a photo of it before tearing out the old motor. I don't know where to connect the three coming out from the upright portion of the machine and the red seems to go to a switch (?) and there is a black (connected t

... Vacuums

Installed a used engine on a 1996 Toyota Avalon xls, and need a vacuum hose diagram so I can run new hoses properly.

Your dealer should have the schematic for your vacuum lines. If not , Auto Zone sells the manual for your car type. However, it is not uncommon to have hoses left over. The extra hoses could be for accessories your car is not equipped with. Hope t ... Vacuums

I am trying to install new belt. I got the bottom of the vacuum off, but now I need a diagram on how to put it back together.

... Eureka 431A Optima Bagless Upright Vacuum


\015\012\015\012Remove the lower plate \015\012\015\012Carefully lift up on the agitator assembly until it clears both sides of the nozzle housing. ... Panasonic MC-V5745 Bagged Upright Vacuum

Oreck xl 21 fan housing has new design. willit stillfit my older vac

It should. You can call Oreck and talk with them and give them the serial number off your vacuum and they can look it up and tell you for sure if it will fit or not. ... Oreck Great XL21 XL 21 8 Pound Upright Vacuum Cleaner

How do I install new hose on little green 1400-5


Putting back together correctly after installing new heat sensor

The hoover website does NOT give screw sizes,unfortunately!\015\012\015\012cut and paste following info\015\012 ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

We had to take the machine apart just to see that the belt had broken after only 5 use's . We can not see how we are ever going to put the new belt back on. do you have instructions on how to take the belt off and how to put a new one on? Please send me one.

I have a Panasonic MC-V5746 upright vacuum. According to the booklet, \015\012MAKE SURE UNIT IS UNPLUGGED.\015\0121. Place carpet-bare floor selector in "carpet" position.\015\0122. Remove lower plate (there are two screws in the m ... Vacuums

I have a Euro Pro Compact Performer model # EP 171 which I love. It is the best iron I have found for my quilting class. When I went to use it, I found my cats had chewed the cord to the point that it is unsafe. I took it to a repair shop to have a new cord put on it and they told me it had to go back to the factory. I do not want to purchase another iron because it is my understanding this model is no longer made and because I love it. May I send this iron back to the factory to have a new

Hi, you may already have found a solution, but I recently saw this same model iron on ebay! ... Euro-Pro Vacuums

How to install a new motor in a filterqueen canister vacuum the old motor was 5 wire and the new is 4 wire. Wire colors are not the same.. - No, I have not disconnected the old wires.

According to my parts house, there's a 4-wire motor for some of the filter queen models and a 5-wire model for other filter queen models.You can still purchase a 5 wire motor. Check out greatvacs dot com. They carry both 4 and 5 wire. ... Vacuums

How to install a new motor in a filterqueen canister vacuum the old motor was 5 wire and the new is 4 wire. Wire colors are not the same..

Have you disconnected old wires yet? ... Vacuums

Kenmore Elite 721.66463500 Microwave died. Didn't even notice until I went to use it. Changed fuse and screen asked to enter the time of day. Entered the time and hit start. The microwave buzzed for 0.5sec and it blew the new fuse I installed.. put in another fuse and the same thing happened.. I measured the resistance in the noise filter. Results: L1-L2 < 1ohm N1-N2 < 1ohm L1 or L2 - N1 or N2 = 0ohms I'm thinking I need a new filter but I also was unable to measure any resistance o

... Vacuums

The Neutral/drive pedal fell off our Kirby G5 vacuum cleaner. I opened up the area housing its connection to the transmission and a couple of the parts were just laying inside. I need a diagram for assembling it and see if I am missing any parts. It was a refurbished machine and a paperclip fell out of the housing when I opened it. Can you help me?

Hi,In the below links you have the parts diagram as you asked will this helps you?If not let me know i will help you more.http://www.fiorijanitorial.com/s-19-kirby-parts-and-bags-generation-3456.aspxhttp://www.vacu ... Kirby G5 Bagged Upright Vacuum

I have the new power on/off switch to replace the old one(Rainbow vacuum). However the new switch has 4 contacts & the old one has 6. Need wiring diagram.

Simply pair 1 each of the power head leads and motor leads on to one terminal and wire the cord as on previous switch. ... Rainbow E series Canister Wet/Dry Vacuum

I have shark vacuum model #V1700Z and doing my move to a new house I never found the charging chord. I don't know if I can buy one for it or should I just buy a new one for only $35.

... Vacuums


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=725726\015\012Generic problem for all Vacuums\015\012I GOT A NEW HOOVER\015\012Posted by junethome on J ... Vacuums

I bought new belts to replace the old ones (one had broken and the water would not feed) My cousin took it apart and now I need to put the new belts on and get it back together - do you have instructions or a diagram?

There are different variations with Bissell. They have the ProHeat series and a Power Turbo series. Below is a link with instructions and diagrams for the Belt Access Door. If this doesn't solve your problem or isn't the correct model, please post ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have a dyson dc07 with a malfuncitoning clutch diagnosed here on fixya. I've replaced the clutch and the grinding noise when the clutch is engaged for carpet and non rotating brush problem presists. This is after replacement of the clutch with a new part. Install of the new part went well and there are no otehr apparent problems with the unit. Ideas? The unit is only a couple years old and not used that much on carpet. For an expensive vacuum I'm not that impressed with it at this point.

Greetings from GoVacuum,\015\012\015\012If you have replaced the clutch already, then this can really only be one other problem, and that is the roller brush. If the roller brush's bearing have locked up, and the brush is no longer spinn ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I purchased a utilitech 7-day digital in-wall timer #0141224. My house wires are two black wires and a green ground wire. The new timer has a w,g, r, and b, wires. My question is what wires do I connect. I found the black power wire from the house. I have no white wire in the switch box. Where would the red wire go? Thank you

Hi!!\015\012\015\012\015\012\015\012The Green wire goes to ground, \015\012The White wire is the neutral. (in this case is used to supply power to the clock.) ... Vacuums

I have a Hoover Windtunnel U 6439-900. The agitator brush will not turn. I installed 2 new belts, # 38528034, and # 38528-035 There is so much slack in belt # 3852034 (brush drive) that it cannot grip the brush. There does not seem to be any adjustment to take up the slack. I've put in new belts twice now & cannot get brush to rotate or tighten the belt to the brush.

... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0575 seconds