Having problems with your Vacuums ?

My electrolux2100 every time i turn it on it stays on for about 1 min then the proctection button come on then the machine turns off i wait a second and then it turns back on and does it again what can i do


Answers :

First, turn dial on top of vacuum counter-clockwise so the smallest dot lines up with the arrow. See if it stays on. If not, detach hose and turn vacuum on. Place palm of hand over intake. If it turns off, it's possible that the tubes connecting to the CVA are clogged and simply need cleaned. This is most often caused by using "made to fit" Electrolux bags. Dust is sucked through the bags and into the motor compartment of the machine. All interior parts get covered in dust and need to be cleaned. If this is the cause, the vacuum is best cleaned and repaired at an authorized Aerus Electrolux store. If the vacuum shuts off, or won't turn on before placing hand over the intake, it's probable the control valve assembly is bad and needs replaced.

Another cause is an overheated motor due to clogged screen at back of bag well, full or clogged bag, dirty afterfilter, bad wiring/connections, clogged hose, clogged power head, or bad motor. It depends largely on the type and model of cleaner. Clogged wands are also a possibility, but unlikely.

Check and clean screen at back of bag well.

Replace bag. Make sure it's a genuine Electrolux bag made by Home Solutions.

Check and replace afterfilter if necessary. These should be replaced after every six bags.

Broken and worn wiring connections are often found in the hose ends due to abuse and normal wear and tear. You can check the continuity of the hose using a continuity tester or multi-tester. If a multi-tester, turn dial to one of the Ohm settings. Place one probe into one of the terminals on the end of the hose. This will be referred to as T1. Touch the other probe to each of the terminals/connections on the other end of the hose. These will be T3 and T4. One of them should read zero, the other should read infinity. Repeat this with the other terminal, which will be T2.

Drop a marble in one end of hose and let it roll through. If it doesn't roll through, the hose is clogged and needs to be cleared. Plug hose into the exhaust port of the vacuum, place other end in the in port. Turn vacuum on. This provides a blowing and sucking action which should clear the hose.
Detach hose from power nozzle (PN). Drop a marble into the wand end of PN. If it rolls through, it's clear. If not, there's probably a clog behind the brush where the intake opening is. You may be able to reach this through wand end with needle nose pliers, or either end with a knitting/crochet needle or a bent coat hanger.

If none of these "fixes" provide the answer to the problem, it should be taken to the nearest Aerus Electrolux store for diagnosis. Repairs or checks involving disassembly of the vacuum should always be done by an authorized Aerus Electrolux service technician.

The store nearest you can be found by following the instructions at the below listed link:
http://www.aerushome.com/storelocator/

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My electrolux2100 every time i turn it on it stays on for about 1 min then the proctection button come on then the machine turns off i wait a second and then it turns back on and does it again what can i do


First, turn dial on top of vacuum counter-clockwise so the smallest dot lines up with the arrow. See if it stays on. If not, detach hose and turn vacuum on. Place palm of hand over intake. If it turns off, it's possible that the tubes connecting to t ... Vacuums

Hi. I have Dyson dc08 hepq+. Thet problem is its not having suction .I checked inside the pipe and foot , ery thing is fine. And if i take the whole dirtbin out ...machine workes fine. when i put ery thing back ....as soon as i start it , after 2 second machine change its voice...and loos suction. I think its just happen because ...the saftey yellow valve inside the machine turns up because the dirt drum is blocked inside some where. Any suggstion ...what can i do with it. I m tahnkful in avance


Hi its Darran at Dyson.From your description of the problem, it sounds as though the bin inner is missing. To confirm this, if you remove the cyclone and bin from the machine, then separate the 2 pieces as if you were going to empty it, w ... Dyson DC08 Hepa Allergy Bagless Canister Cyclonic Vacuum

The vacuum won't start. I used it for about an hour and then turned it off and when I went to turn it back on ..there was no response. I cleaned every compartment on the machine and it's still not working. I also tried using a different outlet in the house. I've waited 24 hours thinking maybe it might have been just the vacuum over heating, but it's still not working.


I had the same problem and after removing the large round filter and cleaning it, (waiting 12 hrs to dry) it started.... ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Mr Coffee EMCP 50 Espresso maker. I tried to brew espresso but the coffee wasn't coming out because it was ground too fine. Now, there are 2 flashing lights one red and green-I have tried turning it off and turning it back on after waiting about 20 seconds so it will reset the pump but it is not working. Any suggestions?


... Vacuums

Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would "heave" (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won't turn. Any suggestio


Carpet brush won't turn when vac on ... Euro-Pro NV31 Infinity Vacuum

Brushes won't turn on the bissell proheat 2X steam cleaner-I don't have the manual to see if there is a button I am not pushing to turn on the brushes. Also, do you put the clean water in the "bladder" in the tank? Sorry I am so dumb-this cleaner was given to me with no manual and I can't figure it out. There is a small tank on the bottom at the back of the machine, that says "formula here" and I don't know if that is where the cleaner goes or what that is for. The machine turns on just fine


... Bissell 8910 ProHeat Clear View Upright Vacuum

The machine backs out of the dock, then proceeds to turn in circles, stop and then start turning in circles again. I have cleaned all of the sensor areas and made sure the bumpers were not stuck against the machine. Any ideas


... iRobot Roomba 560 Robotic Vacuum

Hi. I borrowed my friend's Hoover VC340 to clean my house. I was vacuuming when i noticed the cannister was full, so I turned the vacuum off, pulled out the barrell, and followed the instructions on the barrell to empty it. I put it back into the machine, but it wont turn back on. I tried different power outlets, but to no avail. any thoughts?


... Vacuums

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

My Eureka Altima vacuum the brush is not spinning. I took it apart and the belt is Not broke, but when I turn the vacuum on I can smell the motor overheating. I turned the machine off and unplugged it and then took it apart so I could see the underneath and plugged it back in and the belt still won't turn..can you help?


Hi, since you have detected the the smell of the overheating motor, then the motor is faulty which is why the belt is not turning. You should change th motor ASAP........... ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I have a bissell proheat complete 2x. When I press the trigger to spray the water, it sprays for a couple of seconds and then the pressure drops and stops spraying. I turn turn it off for about a minute, turn it back on and does the same thing again. Jose Cortez


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

CUTTING OFF Our Dco7 cuts off after a few minutes of use. If we wait a few minutes and power it back on it will turn on but turn off again by itself.


Ok What is probably causing the problem is an internal error inside the vacuum. What I recomend you to do is take it back where you bought it and tell them what ever is wrong with it.PLEASE RATE MY ANSWER AS SOON AS POSSIBLE! ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hello, I have a Viking Topaz sewing machine, the top thread is visible on the underside of fabric, indicating a tension problem. I have cleaned the machine, turned it off and back on, rethread it numberous times and tried to manually correct the tension. but nothing helps. What am i missing? Thanks


Thread, Tension, Needle. Make sure your needle matches your application. example: heavy denim needs a heavy needle (90-100) instead of the "universal" needle that usually comes with a machine. Also make sure that when you ... Vacuums

I removed the filter from the motor in the ball. After I cleaned it and let it dry, I put it back in. From then on, it makes a moaning noise when I turn it off after I vacuum. I followed directions to clean it and put it back (it's pretty straight forward and fool proof). I've since cleaned the filter a second time, doing the same steps and it seems to have made it worse.


... Dyson DC25 All Floors Bagless Upright Vacuum

VACUUM ONLY WORKS FOR 45 SECONDS THEN TURN OFF ITSELF. I HAVE TO WAIT FOR 10-15 MINUTES TO START AGAIN USING IT, STOP WORKING AGAIN AFTER 45 SECONDS. VACUUM IS NEW, I COULDN'T RETURN IT TO THE STORE I BOUGHT IT. PLEASE HELP ME TO RESOLVE THIS PROBLEM. THANKS


Sounds like it overheats quickly. But why are you not able to return it? ... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

My dyson hand held shuts down after about 30 seconds, It turns back on again, but it does this over and over again, even after being fully charged with caontainer emptied. Its almost like an overheating thing, but different since it starts right back. It is annoying.


... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

I have an electrolux twin clean cyclonic vacuum cleaner (blue) that turned itself off. I've waited over half an hour an turned it back on. All that happens is the red filter light and the power flash. I have cleaned all filters and replaced them. The vacuum is only 5 months old.


... Electrolux Vacuums

The wand does not have much suction and then when trying to use the wand the machine just shuts off, when I turn it back on the brushes will not turn for a while. Please HELP.


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Pasquini Livia 90 S/E will not stop heating water. This builds up too much pressure. I have unplugged the machine and let it cool off and turned it back on and got the same result. I can relieve the pressure by opening the steam valve, but since the heating element does not turn off it builds up too much pressure very quickly


Your thermostat is failing. Given the initial price tag, look at your warranty options first. If you are out of warranty, then lets proceed.Since there is not a parts / assembly diagram to be found, you will need to disassemble your esp ... Vacuums

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

On/off switch we have two of these vacuums at work, and both of there on/off switches dont work too well. its hard to explain, but when u normally turn it on or off theres a little resistance in the switch and you hear a click, with both of ours the switch moves freely back and forth from on to off, no resisntace, no click, and the machine doesnt stay on, or off for that matter. the switch just moves back and forth.


... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

The unit sprays for the first few seconds after I turn the unit on and then stops spraying any water or solution. I turn it off, wait a few minutes and the same thing happens. What is going on and how can I get it to work properly?


This sounds as though the pump belt is slipping. This may be caused because the pump belt has stretched slightly or the pump is seized and will not turn. Remove the pump belt and turn the pump rotor with your fingers to see it turns freely. If ... Bissell 7901-R Clearview Proheat Plus Upright Vacuum

The Shark steam cleaner wont turn on when plugged in. Is there somewhere on the machine where maybe a fuse was blown or shorted out and needs to have a switch turned back on?


... Euro-Pro Ultra Steam SharkTM II Hard Surface Steam Cleaner Vacuum

My Jacuzzi Tracker 4x just "stopped"..there is a nice strong flow of water going into it, but the wheels just aren't turning. I've tried the following to no avail: 1. blocked suction for a few seconds underwater with my hand (this has worked in past) 2. try to move front wheels back and forth (but they won't budge...back wheels do move on track though) Should I start taking it apart?


... Vacuums

My bissell aroma pro had a horrible burning smell then stoped sucking up water. the motor was still working and water was being feed out just not back up. the machine was hot as i had already cleaned 3 rooms in the house. i let it cool down but the burning prob returned as soon as i turned it back on. any help would be great thanks


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0647 seconds