Having problems with your Vacuums ?

I have lost my sewing machine bobbin case - Vacuums


Answers :

Hi, little ducke,

Can't do much sewing without a bobbin case!

I've had a difficult time finding information on your particular model. The best website I could find has pictures of the few different styles of bobbin case in Janome machines. I think if you look at the pics, you'ld be able to pick out the one for you.  Here's the website: http://sewingstyle.com/Janome-Sewing-Bobbin-Cases.html

I hope this helps. If it does, please place a vote or comment for me. Thanks,

Handie Andie
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have lost my sewing machine bobbin case - Vacuums


Hi, little ducke,Can't do much sewing without a bobbin case!I've had a difficult time finding information on your particular model. The best website I could find has pictures of the few different styles of bobbin case in Janome machin ... Vacuums

Our beautiful Bernina 730 sewing machine has been stored in the garage in its original case, and that wrapped in plastic, for a few years now. Temperatures have been both hot and cold in the garage, but the environment was dust-free. We have brought the Bernina in, set it up, oiled it as specified in the manual, with the original sewing machine oil. We have correctly threaded the machine and the bobbin thread is up. When we press on the pedal to sew, the machine gets electricity and buzzes


Hello and thank you for using Fixya ....From what you describe there can be only 2 causes...Either the machine is still stuck ..and the motor buzzes cause it can not spin it ..and in this case it needs to be oiled more..and be spun by hand unt ... Vacuums

Borrowed Brother XR7700 Sewing Machine 1st: Sewed one inch OK; moved fabric and it stopped sewing, motor made thudding noise. When push-button (NOT pedal) is used, gives error E6, consistent with motor noise. 2d: In order to check threading had to manually PULL bobbin case toward me or it was UNDER needle plate. Cleaned a fair amount of dust out. Reinstalled bobbin, etc., per manual, rethreaded. 3rd: Will sew 2-3 stitches, then packs up again just like in 1st instance above. Have st


Have you checked your needle. it could probably be bent somehow. you should replace it first because that also can confuse the sensor causing that error.regards ... Vacuums

I have a Singer Model #4562 sewing machine. I am having trouble adjusting the tension. Everytime I try and turn the knob to adjust the bobbin just gets looser. Right now it just snags and gets caught underneath the material and bunches up into a big ball. There is a lot of thread inside the bobbin case that came out of the bobbin and has to be cut out to free the material. How do I fix this mess. I am a novice at this. I have not sewn in several years and would like to sew a few quilts


... Vacuums

How do I install the bobbin case and bobbin case body in a model #9420 singer sewing machine


... Singer Instruction Manual - 9420

The case for the bobbin is not locked in and the machine will now sew White Stylemaker 3100 (sewing machine)


... Vacuums

I have a brother project runway limited edition sewing machine and there is a constant jam with the bobbin threading and I have cleaned it,removed the sewing plate and everything I can possibly think of. If the bobbin case is scratched would it cause the jam?


Hi The usual cause is that there is a problem with the upper \015\012threads, often it is not caught in the tension discs. When you thread \015\012the machine, make sure that the presser foot is raised - this causes the\015\012 te ... Vacuums

I have a Pfaff Classic Style 2025. After clearing a thread jam in the bobbin area, the machine will not sew. It works without thread, but I think the bobbin case is crooked. The bobbin opening is off to the right, not up, as it needs to be.


... Vacuums

How to solve a bobbin case popping out of my singer 6233 sewing machine


... SewShop.com Singer Model 6233 Instruction Manual

My kenmore sewing machine (Model #385.11803) isn't picking up the bobbin thread. Bobbin thread case isn't turning. HELP!


... Vacuums

Hi I am looking for Lervia 564 sewing machine manual I was rethreading the bobbin and the casing fell out now It won't pick up the thread from the bobbin


... Vacuums

Elna Corina Sewing Machine: the bobbin thread does not pick up. Someone took out the booin case from the machine, and it was never re-installed correctly. Now the thread will not pick up.


... Vacuums

I have an Eureka Express canister vacuum - I believe it's model 8284 - that just stopped working. Plug it in, turn it on, and absolutely nothing happens. I took it to the local sew and vac place and they say it's a circuit board that is no longer available. I've looked at all the parts lists and diagrams for that vacuum and I would swear there isn't a circuit board there. (I wouldn't have even thought that in 1989 they would have used circuits.) In any case, I absolutely love this machine a


Given the age of the machine weighed against you fondness for it, unless you can find a fault with either the switch or the cord, there is little else that can be done. With time the electrical lead can break down and one o ... Electrolux Vacuums

I have a 144w305 long arm industrial sewing machine i am looking for a bobbin case to replace old one. i am getting alot of skips and was told i need to replace this. any suggestions. thank you


... Singer Vacuums

I have an old Montgomery Ward sewing machine model number UHT J 1964 and it is missing the bobbin case. Where can I find a replacement?


... Montgomery Ward Vacuums

I need to know how to thread a 385 15551 sewing machine. I have lost the manual and can't find a bobbin or a place to put it if i had one.


... Vacuums

My sewing machine is otherwise perfect..but the stitches hv a tiny dot from the thread in the bobbin case...wat to do??


Tighten the bottom thread or loosen the top thread a little. There should be a little screw on the bobbin holder where you can adjust bottom thread tension.lp ... Vacuums

I have a Continental Electric portable sewing machine and I can't get the bobbin to thread into the machine to start sewing. How do I place the bobbin and where does the thread need to go for the need to catch it?


... Continental Vacuums

Jun 24, 2010 - Jun 24, 2010 - Needle not bent/ new needle not answer. I finally conclude that the entire bobbin case is ROTATING in its seat, which jams the needle. The "projection" is against the "spring" when I install it, but I can rotate the bobbin case PAST the spring without trying very hard. Bobbin case MIGHT get held in place better if it were closer to me (front of machine). I feel it is still not out from under needle plate as shown in diagram, but can't keep it closer to f


Hi,Your problem dated 24th June 2010 was re-posted today. If it has been already resolved, kindly ignore this message.Thanks for using FixYa ... Vacuums

So, I was sewing along and heard a thump...kind of sounded like a louder version of what you hear when the needle hits a pin...but I wasn't using pins. This, of course, lead to the thread jamming so I had to clear that. When rethreading I pulled out the bobbin case to make sure it was seated correctly and found a kind of "v" shaped piece of wire (about the width of a paper clip I guess) sitting loose under the bobbin case. I took it out and threw it away. Still can't pull up the bobbin threa


That part was the hook end of the spring that was supposed to put tension on the bobbin - it will have to be replaced. This is a special flat spring that unfortunately only a repair shop of a dealer has it - you will have to take your machine to one. ... Vacuums

I have the brother Ls-2000 sewing machine i threaded the top as well as the bobbin but when i try to sew the thread gets stuck and it bunches up and tangles in the bobbin. also the little bit that did sew was tight stitches on one side of the fabric but very loose on the other side I followed the instruction and it keeps happening i need help i dont know how to fix it please help me


Adjust your tension.You probably did not wind your bobbin properly as well.Make sure you oil your machine every month or so and make sure your bobbin is seated properly before you sew.\012\012Go slower with the pressure foot speed and use the r ... Vacuums

My Kenmore sewing machine timing has gotten off. I am sewing a big upholstery project and it starting bunching thread from the bobbin. The thread is so heavy that I had to put some pressure just to get it undone. This happen a few times and then I found it wasn't sewing at all. When I evaluated without the materials in place I could see the needle would catch on the white plastic piece under the bobbin and the thread would not catch on the metal arm. It appears to be off by 1/4 - 3/8 inch.


HelloDisassemble your bobbin case which is realy quite easy, clean\015\012thoroughly with a brush and air, paying particular attention to any\015\012rust that may have formed, and any thread that may have weazeled it's\015\012way into sma ... Kenmore Vacuums

Janome 6600 sewing machine. bobbin thread is gumming up underneath on a swimsuit knit type material (4 layers). Brand new machine had 1 1/2 weeks. Sometimes material goes down into the bobbin area jammed by needle. What am I doing wrong?


Make sure you're using a polyester thread (I use maxilock serger thread) then a stretch needle, and hold the tails of your thread until you get started into the seam so the fabric cannot push down into the opening on the throat plate.\015\012 ... Vacuums

I have recently got my sewing machine out after several years of it lying unused after moving house. I cannot find the manual. Where can I get a copy of this manual.The second request is that i need to put different cotton onto the bobbin and can't work out how to remove it from the machine. there is a clear "plate" over the bobbin , but I can't seem to remove that.


You posted in the wrong category and there is no mention of make/ model in your question so sadly it is impossible to help you.If it is any consolation this is in part due to the very poor way that the fixya question posting process works. ... Vacuums

While using the pin stitch , the machine has started skipping stitches, knocking loudly, the top thread is breaking, sometimes thread knots up on the underneath side. I have cleaned bobbin area, changed needle and bobbin, using quality thread, the last time I used machine worked fine, yesterday when I started sewing I had this mess HELP!


Hi,Please go through the link given bellow to have the resolution to your problem...\015\012http://sewing.about. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0918 seconds