Having problems with your Vacuums ?

I have a cooks essentials stainless steel 12 in. part # T00099 and i need replacement handles for it. Can you help me out thank you james spaulding email address: [email protected]


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a cooks essentials stainless steel 12 in. part # T00099 and i need replacement handles for it. Can you help me out thank you james spaulding email address: [email protected]


... Vacuums

I had a house fire and lost most of my belongings. But I had just purchased a Shark Steam mop 3501. Loved it. Well it did not get destroyed in the fire but someone managed to break the handle off. Just the handle itself was broke off the rest of the handle rod is ok. I'm trying to see if I can replace the handle and not the whole shaft. Can you help me.


Yes you can replace jus the handle, the replacement part for the handle is available at the manufacturer's web site in the Parts and Accesories section. Enter M/N: S3501 to confirm it's the same as on your unit.\015\012\015\012 ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I have a Kirby Heritage Vacuum Cleaner. Recently the handle fell backwords. I took the pin to the handle out and replaced it. It helped some, but the handle does not stay upright.


... Kirby Ultimate G Bagged Upright Vacuum

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?


Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The solution stick inside the handle needs replaced and I would like a new face plate. I have the model numbers (38458-031 & 37275-011), but can not locate the replacement parts. This machine is more than 10 years old and works like brand new. I can not see throwing it out and want to fix it. Please help me locate these parts. Thank you!


... Hoover Steamvac F5860-900 Vacuum

I would like to replace the handle on the optima 431 dx. The handle will not release. Can you help?


Press down the gray lever ,hold down and pull handle out ... Electrolux 431DX Optima Upright Vacuum Green

We have a Starbucks Barista Aroma Grande Cat. #BA12 1200 W 120 Volts 60 HZ -- bought in about 2006. The lid to the coffee pot has a broken part -- little round plastic disc that when you press the little handle on the lid -- it allows the coffee to be poured. I would suspect we would need the whole lid to be replaced!! Can you help?


... Vacuums

The power head keeps shorting out during use. one of the connecting prongs from the handle to the power head is black instead of silver and is smaller in diameter like it has been arcing inside the connection. could this be the problem and if so can I replace it or will I have to take it to a repair facility. Thank you for your help, Jim Carey [email protected]


This is a problem with the connection in the wands and the powerhead. Because they are shorting out you may have to replace the neck on the power nozzle. (Leave that to a pro). But you will definatly have to purchase a new wand as replacement wires a ... Electrolux Lux 7000 Bagged Canister Vacuum

I am trying to replace the power cord for my 82 year old father-in-law's Oreck XL 2600HH. He already took it apart. I need to know where the semi U shaped spring steel piece is supposed to go inside the Helping Hand Handle? Any drawings or schematics available? Thank you for your time. Arthur


That justs lies on the inner handle whenb you put the spring back. There should be two holds where each end of the spring sits in. ... Oreck XL Ultra Bagged Upright Vacuum

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu


This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

The small button on the hose handle is missing, I need a replacement


... Euro-Pro EP923 Canister Steam Vacuum

Part terminology and replacement help


Call tti floorcare 1800-321-1134. have your model number and the plant number ready you will need it ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

Beam Soft Touch handle electric harness replacement


Set the bottom part of the handle down(not the part that the screws go in)the contact board will fit into slots on the left side of thehandle half, the switch will go where the cutout is for it on the top, the plug is notched to fit at the lower fron ... Beam Industries Wet/Dry Auto Central System Vacuum

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless


Get over it and buy a new one!!! ... Vacuums

No Water My Bissell rug shampooer does not eject water or saop whan I pull the saop trigger on the handle. I checked both filters and they are clean. Then, I removed the container that sucks up the water and pulled the saop trigger, water barely came out of the tubes. I tried to clean the rug in our family room and the rug was not wet when I finished, no water coming out to clean the rug. HELP HELP HELP!!! I live in Colorado is there a Bissell repair shop near Denver, HELP!!! Thanks Dominick ema


Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn't squirt, check for the seal at the bottom of the tank, it needs to be o ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I Have two questions concerning my AIRVAC AV2500 Red Series Vacuum System. How do you replace the light in the floor power head sweeper and can you replace the permanent fabric filter? We had the system installed in 2004 and the light in the sweeper head just went out and can not find any manual on line on how to replace it. The filter if not torn but avter 6 years it probably needs some kine of cleaning or replaced even though it says permanent. Any help would be appreciated. Jim McCluskey


... Vacuums

The extension has lost suction. If I remove the handle tube part, the suction is great to the bendy part, but as soon as I replace the handle part there is none at all and there is no blockage in the handle tube part.


... Dyson DCO3 Absolute Bagless Upright Cyclonic Vacuum

The handle release pedal wasn't allowing the handle to lower. I took off the pedal and saw the spring load part was broken. What is this part and how to replace it? Bissell 3760-3 handle release


Our vacuum recently had an issue with it's motor, we had to borrow a neighbors a couple times while we were trying to figure out what to do. We decided to take it to a place that specializes in cleaning supplies and cleaning tools to see if they had ... Vacuums

Our dustbuster (dont' have model number with me-sorry) won't turn off when I pull back on the switch handle. I disassembled the unit and realize that the tab on the switch handle that pulls back on the internal switch handle to turn it off is not strong enough for its simple task. Does B&D have a proper replacement part?


If you can provide a model number, I can check availability of the switch and can either order it for you, or supply the B&D part number and you can order it from most local vacuum shops in your area or from Black & Decker direct online: ... Black & Decker 15.6 Volt DustBuster Vacuum

I have a Kenmore vacuum cleaner model #116.34720. The problem I am having is that if you are rolling the vacuum around, the base will drop without pressing on the handle release pedal. This often results in a bunch of dirt being dumped back out. The manual doesn't show anything about adjusting the handle release pedal so it holds the handle and base in an upright position better. Any help is greatly appreciated! Thanks in advance!


... Vacuums

Handle broke handle of 2961avz somehow snapped in half. any ideas how to find a replacement handle?


Part # for the handle is 75765-3. You should be able to order thru a local service repair shop. ... Eureka 2971AV EZ Kleen Bagless Upright Vacuum

Bisell Healthy home vacuum stopped working. The troubleshooting guide said there could be a problem in the connection at the handle. None of the phillips screwdrivers we have seem to work in removing the screw that holds the handle to the vacuum. What size phillips screw driver should we be using? If the screw is stripped, how can we get it out to replace it since it is not easily accessible in the handle?


You should use a p2 size phillips. there is only one screw right in the center that holds the handle assy on. frequently that screw backs out and allows the handle to slide back and loose connection. make sure the handle is tightly pressed in and the ... Vacuums

My 8 yr old kenmore vacuum works well - however the hose has worn under the handle where there is a hole (resulting in decreased suction power). I'd like instructions on opening the handle and bypassing the worn piece of tubing rather than replacing it for $129. Some of the handle screws remove easily but the last one doesn't loosen easily.


Hi,Have you tried spraying the stubborn screw with WD40 and let it soaked for a while? Other than these screws holding the handle together, there would no other way of opening it up. Hope this be of initial help/idea. ... Kenmore Vacuums

I have a broken handle for kenmore vacum cleaner model 116.33921300(beltless). I ordered and already got a new handle. I'd like to know how I should deassemblel and put togetger old element to a new handle step by step. Could you help me?


First you have to get the headcover off. After that use a butter knife and/or flat head screwdriver and press forward on the four tabs that retain the pedal. Old Handle just prys off, a new one will press on. ... Vacuums

Need to replace lower handle and pivot as it broke off. I got replacement but no instructions how to replace.


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0596 seconds