Having problems with your Vacuums ?

My Kenmore model 116 33300300C smells like burning when we use it. The bag has been replaced


Answers :

If it is a burning rubber smell it may be the belt slipping. Make sure your brushes are clean and spin freely and then put the belt back on and see if that helps.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Kenmore model 116 33300300C smells like burning when we use it. The bag has been replaced


If it is a burning rubber smell it may be the belt slipping. Make sure your brushes are clean and spin freely and then put the belt back on and see if that helps. ... Vacuums

HOOVER VACUUMS MY MOTHER'S WORK, MERRY MAIDS, USES ALL HOOVER VACS. THEY ARE LIGHTWEIGHT-UPRIGHT-BAGGED VACS. I TRY TO FIX THEM WHEN THE MAIDS BREAK THEM; BUT, I'M HAVING PROBLEMS WITH A BURNING SMELL AND ONE MOTOR EVEN SMOKES. I'M NOT SURE THE MODEL. CAN YOU HELP? THANK YOU.....


Go to thehooverstore - this site lists a whole bunch of hoover machines, exploded diagrams and parts lists. ... Hoover Soft Light Supreme U4262-930 Bagged Upright Vacuum

My vaccuum has lost suction. I changed the bag and cleaned everything out. The vaccuum is only 6 years old. I even replaced the belt around the brush. When I turn the vaccuum on it smells like burning rubber. My vaccuum is an upright 12 amp model #33000300C serial #Y347012385


... Kenmore Vacuums

We replaced the belt after about 5 uses, and now every once in a while it smells like burning rubber, I checked to belt to make sure it was ok, and then last week it started smoking. Is there reported problems with this model?


If the belt is hot or burning during use, it could be due to a beater brush, which the belt drives, being bound up in some manner.\015\012The beater brush is removed during belt changes and should be cleaned of all debris as best you can.\015\012At e ... Dirt Devil Reaction Twin Cyclone Upright Vacuum

Burning smell coming out while using a Hoover's upright vaccum cleaner (model U6434900). Replaced both flat and v-belt. The problem appears to be coming from near the motor area. The manual does not provide any information on how to reach that area. Any help will be appreciated.


Took it to a manufacturer's repair center. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I just bought this vacuum at a second hand store. My girlfriend told me to grab it as it such a quailty product. How ever I can't find a model number or anything else. I need a manual please. Does it take bags? Do I need to replace the filter or just wash the one I have? It is black and silver, cannister. It also says big gary's vacuum system warehouse in surry British Columbia, Canada. It also says to use filter pow-r-nozzle 96. I have no idea of the year.


I suggest you google what you know. I dont think anyone here can suggest where you can get a manual for a machine you dont even know the name of.\015\012\015\012You ask about a bag ... I dont know ... is there one in it now? You ask abo ... Vacuums

I had a real heck of a time with the bag installation, because after the pop i zipped it up and started to use it and then the bag of the vac, not the replaceable bag fell off and i kept putting it back on but it kept falling off and when i looked inside the bag to reattach it to the vac cleaner i noticed that the dust was all inside. i haven't even used it that much as i keep it to do the upstairs bedroom only. i love that it is so lightweight and easy to use and i hope that someone can co


Mary, I have some wonderful news for you and your Oreck XL2600 Vacuum, I called 1 800 989 3535 customer service and inquired about your bag attach problem, it seems to be a docking station problem that "may" be warranteed, however if it is missing ... Oreck XL2600 Vacuum

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless


Get over it and buy a new one!!! ... Vacuums

My 4870 K Boss is 2 years old. I have replaced belts & filters in the specified intervals. This last time I replaced the belt after a year, it shredded 3 of them on the outside edge of the belt in about 5 minutes of use. I ordered a new brush roller & heavy duty belt which I installed. It began shredding the belt in less than 5 minutes of use. What is your suggestion? Is this a known problem with this model? Eureka says no and is not standing behind it.


The only reason why it would be shredding the belt is if the pulleys were not lined up correctly. Check the allignement of the belt to make sure there is nothing kepping the pulleys from being in line. The other thing that it could be is if the rolle ... Vacuums

We have a Kenmore Progressive Model 116 Upright bagged vacuum with Hepa filter. It's at least a couple years old. For quite some time now when ever we use the vacuum the vacuum motor will shut off nafter about 5 min. of use. We then need to let it sit for awhile and then we can run it again for another 5 min. The bag has been change. Any one have any ideas how to fix this?


I suspect that you have a restriction. The motor sounds like the thermal break is stopping the motor before damage, due to heat.\012You must witness that the entire suction and discharge side are clear. This is not always very easy, but necessa ... Kenmore 34612 Bagged Upright Vacuum

I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?


First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums

How to use the function of my use powerstick with edge wedge model#083700,plant, J Household type,mmfg code 699A to deflect my space plastic bags


... Dirt Devil Swift Stick with Edge Wedge Vacuum

I just bought a used euro pro steam shark model ep903, has all parts but when I turned it on to use it water and steam poured out of the handle grip area. Am I not doing something right? The manual says to attach the brush directly to the hand grip but I can't use it without getting burned. Any suggestions would be greatly appreciated! Thanks!


... Euro-Pro Ultra Steam SharkTM II Hard Surface Steam Cleaner Vacuum

I need to replace the bag for Panasonic Vacuum MC-V 9610. Please let me know the bag model and where I can buy the bag. My email is: [email protected] Thanks, Jolly


... Panasonic MC-V9610 Bagged Canister Vacuum

SEARS KENMORE CANISTER VACCUM, Model No. 107-23050, Volts 120AC, Type AV, Hertz 60, Amps 11: This is a small model vaccum with an on/off switch on the canister. The on/off switch has gone and the vaccum can only be used by plugging and unplugging it. I am looking for the replacement on/off switch part but Sears Kenmore has no listing for this vaccum or parts. I can't recall just how long ago it was purchased but could be 10 years (or more). As this model is perfect for the application neede


... Vacuums

Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest


I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum

Hoover Bagless Hello,      My Hoover bag less (Model U5280-900) is not picking up dirt like it should.  The brush roll is spinning fine, but the bristles on it are only about one quarter inch long.  I am wondering how long they should be.  The vacuum is quite a few years old.  Do you think it is time to replace the brush roll.  Could you email me at [email protected] about this topic.  The product bar below did not contain my model no.  The correct model no. is above in my message.  Thanks


If the belt is more than six months old then change it even if it is not broken. then replace your filters if that doesnt work than check the hoses for a clog drop a marble down them and make sure it comes out. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

I purchased a Pro Heat self propelled Bissell rug cleaner model 7950 from Target wherehouse on 4-26-06. I used it once and all was fine. The next time that I went to use it the smart mix for the cleaning formula would not dispense formula.I called Bissell consumer services and was told to take it to Starks Vaccumn in Sherwood, Or. That was on 10-30-06 They said that it was working so I tried it again and not a drop of formula was or has been used since.I took it back 2-13-07 and the replaced the


I assume that it is spraying water? Is the smart mix knob turning freely from one point to the end? If not then there is a problem with the smart mix asm. With liquid in the soap bottle, push the valve in to see if liquid comes out ok, couild be ... Vacuums

I own a self-propelled Hoover Wind Tunnel vacuum cleaner (Model U6425-920). I do now have an owner's manual and was wondering how to clean the Hepa filter on this model (*this model uses a vacuum cleaner bag also).


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=794479\015\012Generic problem for all Vacuums\015\012I own a self-propelled Hoover\015\012Posted by goh ... Vacuums

I replaced the belt in our Eureka Boss Smart Vac, it still seems loose, it uses a type R belt. The beater belt still doesn't seem to turn properly and seems that it doesn't pick up very well when I use it on my berber carpet. We have 2 dogs and I like to use it frequently. I have changed the bags and belt......


Check to see that the beater brush is not frozen up. Pull the brush and clean it, spraying some WD40 on each end piece that holds the brush in place.\015\012Also be sure the belt is properly installed so that the brush turns in the correct direction ... Eureka Vacuums

Belt slipping Belt slips off and rubs causing burning smell from the belt over heating. Of course this puts an indent into the belt and has to be replaced. How do I keep the belt from slipping off? I see no place for a belt adjustment. Which I know would eliminate the problem. Really aggravating to have to replace belt only after two uses.


On the roller/brush where the belt sits if that is scarred up or grooved out that will cause the belt to slip if you can fix roller try but i suggest new roller ... Hoover Company Wind Tunnel U53019 Upright Vacuum

Eureka model 7605 type A - 'the boss' lite. would not power on yesterday. working perfectly before. i replaced full bag with clean bag this morning. still won't power on. is there a reset button, or anything else i can try? Thank You!


... Eureka Vacuums

Bissell 6595 problems with roller brush. I've had this happen with two of the same model. Each one didn't last more than seven months! First, it became loud when vacuuming, then there was a burning smell. When you try to replace the belt, you see that won't do any good because the fitted end of the brush is melted. The housing part the roller brush fits into is melted too. There's no place for the roller brush to fit into. I tried to upload pics, because I don't see how replacing the roller brus


... Bissell 6595 Lift Off Bagless Upright Vacuum

No action Hi: My brush roll won't budge. After we cleaned out all the hoses and replaced a badly worn belt (burned?) when I turn it on the smell of burning rubber and smoke has continued. What hurts is that I don't think I've used the vacuum a total of 10 times ... and I had such high hopes. Ideas?


I had the same problem with the belt breaking and the roller not spinning. I read about giving the roller a couple of revolutions to seat the belt, so I put another new belt on. It still didn't spin. I realized it was the end cap that was not spinnin ... Eureka 2961AVZ Bagless Upright Vacuum

Vacuum Bags what type of bags do i use for this model and can i find them at walmart?


If you can provide the name make and model of the vacuum we could help with this issue. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1237 seconds