Having problems with your Vacuums ?
Kenmore sensor sew 70 thread ie bunching on bobbin.
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Kenmore sensor sew 70 thread ie bunching on bobbin.
My Kenmore sewing machine timing has gotten off. I am sewing a big upholstery project and it starting bunching thread from the bobbin. The thread is so heavy that I had to put some pressure just to get it undone. This happen a few times and then I found it wasn't sewing at all. When I evaluated without the materials in place I could see the needle would catch on the white plastic piece under the bobbin and the thread would not catch on the metal arm. It appears to be off by 1/4 - 3/8 inch.
HelloDisassemble your bobbin case which is realy quite easy, clean\015\012thoroughly with a brush and air, paying particular attention to any\015\012rust that may have formed, and any thread that may have weazeled it's\015\012way into sma ... Kenmore Vacuums
I have the brother Ls-2000 sewing machine i threaded the top as well as the bobbin but when i try to sew the thread gets stuck and it bunches up and tangles in the bobbin. also the little bit that did sew was tight stitches on one side of the fabric but very loose on the other side I followed the instruction and it keeps happening i need help i dont know how to fix it please help me
Adjust your tension.You probably did not wind your bobbin properly as well.Make sure you oil your machine every month or so and make sure your bobbin is seated properly before you sew.\012\012Go slower with the pressure foot speed and use the r ... Vacuums
I have a Singer Model #4562 sewing machine. I am having trouble adjusting the tension. Everytime I try and turn the knob to adjust the bobbin just gets looser. Right now it just snags and gets caught underneath the material and bunches up into a big ball. There is a lot of thread inside the bobbin case that came out of the bobbin and has to be cut out to free the material. How do I fix this mess. I am a novice at this. I have not sewn in several years and would like to sew a few quilts
My kenmore sewing machine (Model #385.11803) isn't picking up the bobbin thread. Bobbin thread case isn't turning. HELP!
Brand new Kenmore Sewing Machine model 385, 16782 It was sewing fine. But I changed to the zipper foot and now the bottom thread just makes a mess, even when I use the regular thread. Can't think what else has changed - I didnot rethread or touch the bobbin.
I have the kenmore 385- 81508. wen im sewing it seems that the thread is not properly hooking with the bobbin. it sews properly for a few stitches then skips
... Kenmore Vacuums
My kenmore sewing machine model 385.15212, 15616 the bobbin will not go all the way down so I can thread a new bobbin?
I have an Emerald 203/183 sewing machine and am having trouble changing the bobbin. I have tried to follow the instructions but to no avail. The lower thread keeps bunching up.
Kenmore YM-40-35 R Sewing Machine Manual (or copy) wanted. If a manual is not available, I'd be OK with instructions for threading the needle and bobbin and any additional details that an expert may have. I think the machine may be a Canadian model number, it looks old, made of metal with screwed in presser foot. Thanks v. much. Elizabeth, [email protected]
Hello,please kindly visit the site below to see the comprehensive instruction with video on how to thread and bobbin your sewing machine.http://www.wonderhowto.com/how-to-thread-mechanical-singer-sewing-machine-224245/wish you ... Vacuums
I was given this Kenmore Model# 385. 17324990, sewing machine, no manual came with it. I cannot figure out how to remove the bobbin to re-wind it, and how to thread it to re-wind.
I have a Continental Electric portable sewing machine and I can't get the bobbin to thread into the machine to start sewing. How do I place the bobbin and where does the thread need to go for the need to catch it?
... Continental Vacuums
Borrowed Brother XR7700 Sewing Machine 1st: Sewed one inch OK; moved fabric and it stopped sewing, motor made thudding noise. When push-button (NOT pedal) is used, gives error E6, consistent with motor noise. 2d: In order to check threading had to manually PULL bobbin case toward me or it was UNDER needle plate. Cleaned a fair amount of dust out. Reinstalled bobbin, etc., per manual, rethreaded. 3rd: Will sew 2-3 stitches, then packs up again just like in 1st instance above. Have st
Have you checked your needle. it could probably be bent somehow. you should replace it first because that also can confuse the sensor causing that error.regards ... Vacuums
My jenome 4119 will not sew after I took out thread twisted around the inside of the thread takeup mechanism. It but will not pick up bobbin thread and if it does the stitches r inches apart or none a
I have had 226R 20 years. Don't use it much. I have learned to pull slack out of top thread to start so I do that. However, sometimes, as today, it will wind the thread around the bobbin holder and I have to take time to ge it all out clean it up. Is something out of adjustment or what. Sometimes it will sew OK then all of a suden it will start to wind the thread around the bobbin holder again. So I'm confused. Do you have any ideas. Thanks
Hi wwilson63,What make is that 226R?The problem is that the thread is not threaded correctly. You must be very careful and follow directions explicitly.Once you think you have it threaded correctly, sew a few stitches and see ... Vacuums
Bobbin not threading through, spool thread is gathering in bobbin catch and not sewing - just clumps of thread
It would appear to be threaded wrongly. Pull all the threads out, check the visible upper tension discs for broken threads then re-thread top and bobbin, making sure the pressure foot is up when you re-thread. Bobbins should normally turn clockwise ... Vacuums
While using the pin stitch , the machine has started skipping stitches, knocking loudly, the top thread is breaking, sometimes thread knots up on the underneath side. I have cleaned bobbin area, changed needle and bobbin, using quality thread, the last time I used machine worked fine, yesterday when I started sewing I had this mess HELP!
Hi,Please go through the link given bellow to have the resolution to your problem...\015\012http://sewing.about. ... Vacuums
I want to get my XL-5000 singer sewing machine to work. It does not sew. The top thread will not pick up the bobbin thread for one thing and the other problem is that it gives me a error message saying incomplete threading.
Check if there is any thread in the bottom bobbin and next remove it and give it a good clean in its surrounding area.Oil surrounding mechanism carefully and manually push the top needle in and watch the bobbin spinning a see if it tried to pick the ... Vacuums
I have a Pfaff Classic Style 2025. After clearing a thread jam in the bobbin area, the machine will not sew. It works without thread, but I think the bobbin case is crooked. The bobbin opening is off to the right, not up, as it needs to be.
Our beautiful Bernina 730 sewing machine has been stored in the garage in its original case, and that wrapped in plastic, for a few years now. Temperatures have been both hot and cold in the garage, but the environment was dust-free. We have brought the Bernina in, set it up, oiled it as specified in the manual, with the original sewing machine oil. We have correctly threaded the machine and the bobbin thread is up. When we press on the pedal to sew, the machine gets electricity and buzzes
Hello and thank you for using Fixya ....From what you describe there can be only 2 causes...Either the machine is still stuck ..and the motor buzzes cause it can not spin it ..and in this case it needs to be oiled more..and be spun by hand unt ... Vacuums
We have a vogue stitch janome model 539 115v sewing machine. we were trying to sew but, the thread is not picking up from the bobbin. the thread keeps breaking and we are unsure what tension setting should be used for cotton cloting. please help. thanks! tom staron
I have a brother project runway limited edition sewing machine and there is a constant jam with the bobbin threading and I have cleaned it,removed the sewing plate and everything I can possibly think of. If the bobbin case is scratched would it cause the jam?
Hi The usual cause is that there is a problem with the upper \015\012threads, often it is not caught in the tension discs. When you thread \015\012the machine, make sure that the presser foot is raised - this causes the\015\012 te ... Vacuums
Cant figure out how to thread elna 1000 lotus sewing machine. also the bobbin keeps getting tangled. if you could send me a diagram on how to thread and bobbin i would appreciate it
Sewing machine won't pick up bobbin thread
Open the bobbin case and see if the hook is turning, if it is it is just a timing problem with the hook and needle, if it isn't tuning you may have a broken gear or timing belt.....It eill need to be looked at or adj by someone who repairs them....Da ... Vacuums
Singer 327 lower bobbin thread is wild and loopy after I sew...top stitch fine. Just changed to a large thread spool with the heavy remote base and crook to carry thread to machine and wonder if this changed tension (set at 4 and correctly threaded)? It had been working fine in zigzag but I also went back to reg foot and set stitch width at 0, center needle set. Thanks for your input and help. Deanna
... Singer Vacuums