Having problems with your Vacuums ?

We have a Dixie Narco DNCB 240M/138-6 PE2299 Soda Vending Machine How do we increase the amount per soda?

Answers :

Check behind the coin mechanism. When you open your machine, pull out the coin mechanism. You will see a set of dip switches there. Go to this page for more help. http://www.vendingadvantage.com/troubleshooting.htm
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We have a Dixie Narco DNCB 240M/138-6 PE2299 Soda Vending Machine How do we increase the amount per soda?

Check behind the coin mechanism. When you open your machine, pull out the coin mechanism. You will see a set of dip switches there. Go to this page for more help. http://www.vendingadvantage.com/troubleshooting.htm ... Vacuums

I have an older model Bissell rug shampoo machine, model # 1631. I have several bottles of Bissell 5 One carpet formula to use in this machine, however I have lost the measuring bottle that tells me the amount of soap solution to use per 64 oz. bottle of water. I sure would appreciate if you could help me.

I have a older mod. Bissell carpet machine plus mod. 1630-5 and need a floor nozzle part num.013-6194 and grip tube w/button part num.014-4181 and trigger part num.010-9406 and tube ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Borrowed Brother XR7700 Sewing Machine 1st: Sewed one inch OK; moved fabric and it stopped sewing, motor made thudding noise. When push-button (NOT pedal) is used, gives error E6, consistent with motor noise. 2d: In order to check threading had to manually PULL bobbin case toward me or it was UNDER needle plate. Cleaned a fair amount of dust out. Reinstalled bobbin, etc., per manual, rethreaded. 3rd: Will sew 2-3 stitches, then packs up again just like in 1st instance above. Have st

Have you checked your needle. it could probably be bent somehow. you should replace it first because that also can confuse the sensor causing that error.regards ... Vacuums

After charging overnight, Roomba only runs about 25 minutes before shutting down with a red light.At this point the battery measures 15.13 volts ( about 1.26 volts per cell ) My hobby experience is that a ni/cad or ni/mh battery nominal charged voltage is about 1.2 volts per cell, and that the recommended end point voltage should be about 1.0 volts per cell. Seems like the battery is ok, butsome kind of voltage regulator is shutting things down prematurely. Is this happening, and , if so, how ca

Reset the Roomba by removing it from the charger, then holding "spot" and "dock" for about twelve seconds. When you let go, the unit will play an ascending series of notes. Then recharge it overnight. If the run time is still short, give Customer Sup ... iRobot Roomba 560 Robotic Vacuum

When pluged, in the unit turns on ( green light illuminates ) and feels warm. Yes, I filled the water container. The unit does not generate any steam. For some reason, I do not have an "operation manual" --- but it doesn't seem to be all that complicated! Have left it plugged in for 25 minutes. A small amount of water came out while just sitting. Then another small amount of water comes out when I push the handle in. I will assume that steam should come out when I push the handle in. Well, it do

Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Shop Vac 90PN575A shuts off by itself when suction increases.

... Shop Vac 401-04-62 Original Wet/Dry Vacuum

Vacuum turns off after short amount of use

Check the vacuum for a clog somewhere, check any filters to see if they are dirty (i understand filters are going to be dirty after use, but i mean extreme dirty in this case), these are common things to look for when you have this problem ... Electrolux Guardian Bagged Canister Vacuum

Machine does not spray fluid on rug when trigger is depressed. have tried repriming pump per trouble shooting manual. No help.

Hi\015\012Either soap deposits or dirt was clogging the spray endings. Here is what to do to clean up the spray endings:1. Remove the water container from the bottom unit2. Look up for two red plastic endings on the bottom uni ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum


Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem. ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Amounts of Solutions

From the manual:\015\012\015\0121. Remove the Clean/Solution Tank by lifting it\015\012straight up, then away from the Lower Body.\015\0122. Unscrew the black cap at the bottom of the\015\012Clean/Solution Tank.\01 ... Bissell 1770 QuickSteamer Upright Vacuum

My panasonic vacuum cleaner is not working to its full amount .so i need it repaired.i am at present in bahrain.could you please tell us any service centre so that i can get it repaired.

Country:\015\012Bahrain \015\012\015\012Agent Name:\015\012Al-Futtaim Sons Co. WLL \015\012\015\012Address:\015\012P.O.Box 2722, Manama, Kingdom of Bahrain \015\012\015\012Tel1:\015\01200973 17564776 ... Panasonic Vacuums

Suction hose I can't get the suction hose to work...and I have cleaned it out to make sure it isn't plugged. There is a small amount of suction just not enought to pick anything up.....the floor part works great...what could be the problem

I would first double check the hose, remove it and drop a marble through it to be sure. make sure the bag is new and also check the filter underneath the bag if it is clogged it could cut the suction. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My Bissell Proheat has stopped suctioning the water solution. It has worked well in the past, but the last time I used it the recovery bladder had just a small amount in it. Could it be stopped up?

I have this machine too. IF the soap dispenser does not have anything (even water) in it the water sprayer will not spray. Sometimes the water valve from the tank has an air bubble in it. Remove the tank and push up the valve. A little water will fal ... Vacuums

The vaccum won't pick up the water and there is large amount of air blowing out the bottom like it is bypassing

... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Hoover carpet cleaner F7458-900 issue The detergent is not dispensing? Tried cleaning the valve cap (per Hoover manual) yet the issue persits. Any advise?

The pointed valve that is in the tank may need replacing. The two valves are a set. I just ordered some from www.usavacuum.com ... Hoover F7458-900 Upright Vacuum

I bought a Hoover Wind Tunnel in January 2008. At first it worked great though very noisy. Now it will not pick up small fuzz on medium shag carpeting. I have checked the bag, the filter, the belt, and obstructions and there are none. Plus the noise level has increased. What is wrong? I am very dissatisfied.

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=563001 Generic problem for all Vacuums I bought a Hoover Wind posted by smithcarolj1 on May 01, 2008 I bought a Hoover Wind Tunnel in January 2008. At first it wo ... Vacuums

HOOVER Cleaner F5857-011 BRUSH'N'WASH Problem: Brushes not turning under load. Will turn slowly when raised from floor/carpet but can be held still by light hand pressure. Checked listed possible causes as per handbook but still not working.

... Hoover Vacuums

I have a Harmony vacuum that's a couple years old. I recently sucked a fair amount of dog hair into it and was unaware something was amiss since the things so quiet. It just shut down and wouldn't come back on. 10 minutes or so later it came back on but now it's got no sucking power. I figure I torched the motor. Good guess? What are my options--I'm out in the middle of no where but can get it to a repair shop 250 miles away. Is it worth trying to salvage or am I going to pay as much to get it f

I cleaned the whole thing out, changed out all the filters again and cleaned out the motor compartment. Then I discovered a huge clog in the line. Once I got that all done--it's now working like a charm. Moral of the story: spend more time looking fo ... Electrolux Vacuums

Hi The band snapped the other day on my Vax Swift Turbo upright hoover and i got a new band from a Hoover repair centre. (Im assuming the bloke sold me the correct band). Was tight to go on. And it seemed ok. However, after switching on the band snapped immediately. Kinda burnt as well (at the point it snapped). Any ideas as to what the problem is here? The hoover is roughly 2 years old and used around 3 times per week. thanks Mike

Sounds like the brush roll is bad. Did you check the ends to make sure they turn freely? If not, replace it. ... Vacuums

I just bought a westinghouse unplugged vacuum cleaner.( It is new) The design is awesome, and when it works it works great . But it has very short battery life. 1 battery lasts only about 5 minutes, and the other is even less. I did all the instructions told me as far as conditioning and charge yet I still do not get a very solid amount of vacuuming time. Is there any thing I can do?

Usually a short battery life means bad battries that aren't holding its charge. Being new I would think it would have a year's warranty on it. Find out who is the closest warranty shop and have them fix it. ... Vacuums

Hoover SteamVac F7222-900 steamvac Brushes do not spin. Looked at filter as per manual instructions but it was free of lint. Need to fix it, help please? Vacuum was used less than 10/12 times

Solution for Hoover SteamVac (F7452-900) brushes not spinning\015\012Uses the turbine model and same solution would be similar. Root cause is simply the main gear attached to turbine becomes stuck. This problem shoul ... Hoover Vacuums

I have a nearly 9 year old Electrolux Excellio Z5228 vacuum cleaner. It has recently started cutting out during operation. I cleaned the micro filter (between bag & motor) via brush & hitting against wall & seems / looks quite clean. I washed the gore filter (output from motor to clean the exhaust air) as per instructions, then let to dry. It was very clogged but now very clean. The vacuum clearner still cuts out often. Even after a long rest (say overnight) it still won't start, then ano

... Electrolux Vacuums

How can I increase the vacuum setting on my food packaging machine? Which way do I turn the adjustment screw?

As the screw turns into two directions try the other direction and test to see if it increased or decreased, then adjust to the other direction if the result wasn't what you wanted.\015\012 ... Vacuums

Not charging After being on the charger for a long time, 24 hours, it barely starts to run, then increases spead some but not enough to pick up. Can I get a new battery or is it just a goner?

There could be reasons for this. \015\012\015\012Firstly check the air waves of the hand held unit by inspecting the slide out built in crevice part - if its clogged - remove it.\015\012\015\012Secondly, check the brush roll a ... Electrolux EL1000A2 Pronto Bagless Stick Cyclonic Vacuum

No suction I just replaced the bag, and normally after this I have a lot of suction. Now that I have changed the bag I have less suction that I had before. Not even enough to picj up dog hair. I snaked he hose and checked all of the connections. It seems to have an air leak but no amount of tape will fix this. I cleaned the filer as well with warm water and dried it and re installed but still absolutely no suction. I am ready to throw it out! Any suggestions would be appreciated

1, Does the blower (discharge) side blow bunches of air??Yes: Something is clogged from the bag to the hose end. Try blowing out the hose from the discharge side.Or: The bag is not properly seated. Make sure that the plastic piece is ... Kenmore 23313 Whispertone Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0209 seconds