Having problems with your Vacuums ?
I have hoover steamvac models f5889-900 and f7222-900.
The brush motor is broken in model f7222-900 and I replace with working motor in f5889-900? I am using f5889-900 just as parts
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
I have hoover steamvac models f5889-900 and f7222-900. The brush motor is broken in model f7222-900 and I replace with working motor in f5889-900? I am using f5889-900 just as parts
Have a Centralux Aerus about 5 years old. Don't see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced
There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself ... Electrolux Centralux Vacuum
Model, 116.c85pbpk0v022 Power-Mate Jr. attachment stopped working, could it be a part within the unit (i.e. the electrical component) or do I need to replace the unit? How do I troubleshoot the electrical connection? No known drop or abuse. Worked last time I used it.
This model frequently stops because, lint, hair, etc. gets caught between the two end pieces of the brush cylinder. Do the following to fix it:1) Remove the two Philips screws from the underside of the unit. 2) The side with the tag will ... Kenmore Vacuums
I have a kenmore vacuum cleaner model # 116.23612. When the hose is attached to the canister it runs, but if you remove the head to just use the hose the unit stops working. Is the motor dead or is there some type of reset or fuse. Could you please tell me how to test this. If so could you please send me instructions on how to replace the motor. Thank you in advance for your help, Tony
... Kenmore Vacuums
My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc
... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
We have inherited a Filter Queen Majestic Triple Crown Model 99C vaccum and have no owners manual stating the year it was purchased and parts available. Our power hose electic wire connection (about 6 inches long) which plugs into the main unit is split in the hose attachment end. The motor sound went instantly quieter and I wondered if this was why when I found this frayed electical wire. It has not been used since this problem was found. How much is this single replacement part? I live
My QSP Contractor Wet/Dry Vac stopped working without any signs of a burned motor. My vac is steel tank, 6.5 hp, model #86776 24. Where can I find replacement parts?
... Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum
Replacement parts... I've got a 3594 Bissell and the belt has come completely off. In the process of breaking, it bent the metal guide inside the motor housing and melted the plastic that holds the guide and keeps the belt inline with the roller. I've got it running again by using a screw I filed all the threads off of, but it only works for 10 minutes at a time before breaking another belt. This process is getting expensive, as it usually takes 30 minutes to completely vacuum the house. Is ther
Most likely it is the top cover that needs to be replaced, part #2031238 and is around $30. It would have that guide on it. ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum
Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless
Get over it and buy a new one!!! ... Vacuums
SEARS KENMORE CANISTER VACCUM, Model No. 107-23050, Volts 120AC, Type AV, Hertz 60, Amps 11: This is a small model vaccum with an on/off switch on the canister. The on/off switch has gone and the vaccum can only be used by plugging and unplugging it. I am looking for the replacement on/off switch part but Sears Kenmore has no listing for this vaccum or parts. I can't recall just how long ago it was purchased but could be 10 years (or more). As this model is perfect for the application neede
Power nozzle of my S3670 does not work (vacuum itself does work), the headlight bulb in the nozzle is broken. This happened in the past several times - we would bring the vacuum to service center - I don't know what they did other than replacing the bulb. I decided to go to ACE and buy replacement bulb myself, replaced the one in the nozzle - this did not fix the problem. I don't see any fuzes or anything in the nozzle. However, the manuals says to "Use only HOOVER part no. 27317307, which is a
... Hoover S3670 Bagged Canister Vacuum
My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?
Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
The solution stick inside the handle needs replaced and I would like a new face plate. I have the model numbers (38458-031 & 37275-011), but can not locate the replacement parts. This machine is more than 10 years old and works like brand new. I can not see throwing it out and want to fix it. Please help me locate these parts. Thank you!
... Hoover Steamvac F5860-900 Vacuum
Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest
I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum
Where can I order the following parts for my 1952 KENMORE SEWING MACHINE MODEL #117583, SERIAL #48054: : #5107 carbon motor brush (2) #5110 motor brush spring (2) #5111 motor brush spring cap (2) String for starter control lever Pulleys, screw and nut washer to attach string control Best sewing machine ever and still working like new, and I want to keep it that way. Thanks.
After using switch to go from floor to carpet, noticed the roller brush not working, and therefore the self-propelled feature also not working. Replaced what I thought was the problem, a loose belt, but still does not work. Motor runs and there is suction...???
... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum
I purchased a Pro Heat self propelled Bissell rug cleaner model 7950 from Target wherehouse on 4-26-06. I used it once and all was fine. The next time that I went to use it the smart mix for the cleaning formula would not dispense formula.I called Bissell consumer services and was told to take it to Starks Vaccumn in Sherwood, Or. That was on 10-30-06 They said that it was working so I tried it again and not a drop of formula was or has been used since.I took it back 2-13-07 and the replaced the
I assume that it is spraying water? Is the smart mix knob turning freely from one point to the end? If not then there is a problem with the smart mix asm. With liquid in the soap bottle, push the valve in to see if liquid comes out ok, couild be ... Vacuums
My filter queen majestic quit working. I opened up the unit to see what was wrong and I did not immediately notice anything wrong. Upon furter examination I noticed one of the traces on the printed circuit card was burnt. I used a soldering iron to "bridge the trace and it appeared to fix the problem for a while. Now it has stopped working again, and when I jumper the trace to run the motor it seems to work. Should I just replace the card? Or is there a more serious problem with too much current
I recommend replacing the card. Soldering involves the risk of further damaging the card, so it would be useless anyway. Why waste valuable time?\015\012There is a possibility of the motor overheating, generally due to a blockage in the airfl ... Filter Queen Majestic Canister Vacuum
My 20" Patton electric fan has stopped working. I use it for animal cooling and it operates in dusty conditions. I suspect that the motor is shot. Is it worthwhile to replace the motor and are motors even available?
You could just try to clean the motor out by taking it apart, and shining the shaft up. then put some motor oil/engine oil on the shaft. That will work 99% of the time. ... Vacuums
I have an eureka deep steam extractor 2590 series and everything is working fine except for the motor it isn't moving is there a replacement part for the motor?? we think iit is the motor but could be wrong ??
Repairing unit wouldnt be cost effective . parts/labor $75.00 /$100.00 .if parts even available . ... Eureka Atlantis 2590A Wet/Dry Vacuum
I can't find replacement belt for little lux (original model bought in 1991). Stamped on back "Model 1673BA". Motor works fine but belt doesn't turn roller any more.
... Electrolux Little Lux Bagged Handheld Vacuum
I have a Gemmy light show strand of bulbs, model 19611. I bought 4 strands last year the day after Christmas and used them for the first time this year. After two days use one of the strands went out. I have replaced the fuses in the strand and it is still not working. Any ideas?
I have a Philips vacuum Cleaner model FC9104. The on/off switch does not work (it appears to be part 11a and/or 11 on this the parts list document). Is it easy to replace?
... Philips FC9104 Bagged Canister Vacuum
Replacement parts where can i find replacement steam pocket towels online for the shark ultra steam blaster hard surface cleaner? I went online to www.sharkcompany.com & www.sharkvac.com and when I enter my model number S3325 search comes back with 0. Thanks
You can found them on amazon, take a look here: Amazon com Euro Pro S3325. I hope this was helpful. Cheers ... Euro-Pro S3325 Handheld Steam Vacuum
Our kenmore progressive model #11634922 was working fine today. And then - it's not. Plugged in - nothing is working on it. We let it cool down (though it didn't seem hot). Still nothing - no light, no motor. Tried it in some other plugs that we know are functioning well - and still nothing. Any idea what might be wrong with it? It's six years old but doesn't get heavy use. Thanks so much ~ Susan Golden
Hi, it could be a number of things, cord may be bad as well as a problem with the motor. There also is a fuse that could have blown. If you go to sears.com, click on parts, put in your model number, when the page loads, click on the first link ... Kenmore Vacuums