Having problems with your Vacuums ?

How do I tension an elna 614de? - Vacuums

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I tension an elna 614de? - Vacuums

... Vacuums

I have an elna 3007 machine. Our service man died and I need help with the tension. I can't get the top tension number to change off zero. when I free motion, all I get are loops top and bottom. I have adjusted the machine the best I can but still have the problem. I'm in the middle of a quilt and could use some help.

... Elna Vacuums

The brushes will not rotate on my hoover vacuum. the belts are in good shape, the motor is turning the vacuum motor, but the belt on the brushes seems loose. I ordered a replacement belt but still nothing. Their is a small "idler" but their dosent seem to be enough tension on the belt. Any ideas?

Did you order the correct size of belt? These are the belts you should have:Hoover Windtunnel Belts ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.

... Hoover U6485900 Bagged Upright Vacuum

How do i change a tension bar on an oreck vacuum

... Oreck XL Ultra Bagged Upright Vacuum

I'm after Elna Diva manuals - Vacuums

You should be careful to check where the error occurred ispandora charms ... Vacuums


... Vacuums

I have an elna 614DE overlocker and although there is power (light on) when I press the foot pedal, nothing happens. Is this a fixed unit which can't be repaired? If so, where can I get a replacement?

I have the same machine same problem did you get it working and if yes what did you do. ... Vacuums

Repair manual for an Elna SU sewing machine - Vacuums

... Vacuums

Elna TX electronic manual avaliable on line? - Vacuums

... Vacuums

I cannot find my manual for my Elna serger and I need to have the tension # settings to make a flat seam that will be on the exterior of the garment. Any chance you could help me? Sue

... Vacuums

User manual for elna 2005 sewing machine - Vacuums

... Vacuums

Manual for elna diva sewing machine - Vacuums

You can find a free download of the manual for the Elna 9000 which is almost exactly the same as the Diva.\015\012http://pdfdatabase.com/search/ma ... Vacuums

Elna 2007 sewing machine manual - Vacuums

... Vacuums

Elna sewing machine type Top 300 manual - Vacuums

Http://www.sewingpartsdirect.com/elna-model-300-instruction-manual.aspx ... Vacuums

How do i replace my DC28 vacuum tension belt?

... Dyson DC28 Animal Bagless Upright Vacuum

Put on a new beater brush belt that I bought from Sears as detailed on the plate on the vacuum. It immediately snapped. Is there a diagram for the routing for the belt (there is a drive spindle and a tensioner)? Thanks.

I would first check to see if the beater brush is turning freely. You should be able to turn it by hand. If you can not, remove it from the vacuum and clean any debris on the brush and especially on the ends that hold it in place.\015\012Some WD40 ... Kenmore Whispertone 29512 Vacuum

My bobbin thread forms massive amounts of loops and a knoty mess. I have tried adjusting the tension and changing the needle. What can I do?elna 3005

Hi\012you just have to open up the bobbin part with a screw driver, take out the bobbin and bobbin case, use a small lint brush clean the whole area.insert the bobbin back once you have finish. There must be a lot of lint in the area it can cause the ... Vacuums

I have a Miele S1721 Powerhouse upright vacuum. When the belt broke I took it into the shop (because when i tried to replace the belt, the tension was so tight I couldn't get it back together!!). When I got it home I DISCOVERED THAT THE HEIGHT ADJUSTMENT DIDN'T WORK anymore. It seems like it's set really hight, because it no longer contacts and brushes the carpet. So it's now useless. I went back to the shop and the tech denied that there was anything wrong. (I didn't have the vac with me). No

Hi\015\012The Miele uprights (S170 and upwards) with the Powerhouse title are ALL Panasonic uprights which have been at one time sold in the UK. Therefore the upright may use TWO drive belts which need to be looked at: Take off the sole plate a ... Vacuums

Elna pro 4de users manual - Vacuums

Hi,You can purchase it from your dealer. You can locate a dealer in your area on this site.The availability of free ... Vacuums

Pro 5 dc elna lock serger manual - Vacuums

I need instruction how to do roll hem on my pro 5 thread Elna serger 9000. ... Vacuums

Looking for elna 3007 instruction manual - Vacuums

... Vacuums

Dc07 problem I have a dc07 cyclonic vaccum and like this model,however, for some reason,it has been very dificult to push and pull for the past month or so. i have completely cleaned the brush assembly,cleared any obstructions in the hoses,and, cleaned the filter.I also checked the belt tension,wich i thought was fine but to no avail.Be advised that the brush assembly is spinning and suction is excellent. It just feels like the brush drags along the carpeting. this is a great vacuum cleaner and

The dyson uses two belts, one from the motor to a clutch and then from the clutch to the brush roller, the belts that they use are not much better then any other belt ( those you should change yearly ) but you cant just change the belts you have to c ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Have a elna 792d but cant seem to get the tensions right since changing thread

... Vacuums

I'm replacing part # 8175156 cord reel on my Kenmore canister vacuum. How do I tension the spring? Do I do that before winding the cord onto the reel?

... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0601 seconds