Having problems with your Vacuums ?

Getting an H97 error code on a Panasonic micro wave, I believe I am having an inverter problem


Answers :

Troubleshooting of Inverter Circuit (U) and Magnetron
This oven is programmed with a self diagnostics failure code system which will help for troubleshooting, H97, H98 and H99 are the provided failure magnetron and inverter circuit problem areas. This section explains failure codes of H97, H98 and H99. H97, H98 and H99 appears in display window a short time after start key is pressed and there is no microwave oscillation.

zjlimited_1131.jpg

NOTE: DO NOT try to REPAIR this Inverter Power Supply (U) and also DO NOT RE-ADJUST PRESET VOLUME on the board. It is very dangerous to repair or adjust without sufficient test equipment because this circuit handles very high voltage and very large current. Off alignment or inverter board operation is dangerous. Operating a misaligned inverter circuit is dangerous due to the very high voltage and current that is produced by this board. Defective boards must be replaced with a new one.
- Check magnetron filament for open or short to casing before proceeding to determine a good magnetron.

Alternative way to troubleshoot oven with AC Ampere meter used. H97, H98 and H99 appears in display window a short time alter start key is pressed and no microwave oscillation with AC Ampere meter used for troubleshooting.

zjlimited_1132.jpg

NOTE: DO NOT try to REPAIR this Inverter Power Supply (U) and also DO NOT RE-ADJUST PRESET VOLUME on the board. It is very dangerous to repair or adjust without sufficient test equipment because this circuit handles very high voltage and very large current. Off alignment or inverter board operation is dangerous. Operating a misaligned inverter circuit is dangerous due to the very high voltage and current that is produced by this board. Defective boards must be replaced with a new one.
- Check magnetron filament for open or short to casing before proceeding to determine a good magnetron.

Hope this helps.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Getting an H97 error code on a Panasonic micro wave, I believe I am having an inverter problem


Troubleshooting of Inverter Circuit (U) and MagnetronThis oven is programmed with a self diagnostics failure code system which will help for troubleshooting, H97, H98 and H99 are the provided failure magnetron and inverter circuit problem areas ... Vacuums

Pfaff 2140 Getting an error code that reads: error in read parameters, and if this error occurs several times contact your dealer. -then you have to hold a crosshair on the screen push the scissor trim button and reverse button to get back to the main menu. I just had it in for service a month or so ago...?so there should not be any major issues, what does this error code refer to?


... Vacuums

Hi, I have a Xenon 600 VA sinewave inverter. My inverter starts working even when the main power is ON.So the battery gets dried up even when power is there.Can I know why this is happening? Is this due to main power line problem or a inverter problem.


... Vacuums

My Roomba 770 will not start. When I push "clean," "spot," or "dock," I get one beep. There is no voice error code like with other errors. I am still able to drive it around manually with the remote c


The beep code means that it cannot verify all of its wheels are on the floor. Turn the unit upside down and make sure there is nothing stuck to the wheels or sticking between the wheels and chassis ... Vacuums

Codes getting an er4 error code, dont know how to fix


... Dri-Eaz Drizair 1200 Dehumidifier

I am trying to install a train air horn. i bought a viair compressor for it. the horns themselves have a 12 volt hookup going to what i believe is acting like a solenoid. when charged, you complete the circuit and walah, the horn blasts. the problem im having is when the compressor is building pressure, the air horn is automatically putting out a dull sound, getting louder as the pressure gets more and more. it sounds like its out of one horn however. it is doing that without the 12 v hookup. is


Hi! just a tip regarding the sound that comes up when building pressure. Is there a gasket or rubber seal on the horn? You may need to replace this for it may be worn. The air may be coming out of the worn seals resulting to sound even when not trigg ... Vacuums

I have had my RCA microwave model # RMW1108 for about 8 months now. It was working fine until yesturday evening. I went to warm up some food for 2 minutes, the microwave itself was on and everything appeared to be working except my food did not get warmed up. I plugged it out and checked all over it for any damage but i could not find anything wrong. What would cause it to just stop heating up the food? Is this type of problem covered in the 1 year manufacturer's warranty.


... Vacuums

I have an error code of E42 on my Samsung Cm1929 1850 W microwave


Sorry to read about your problem, I hope this helps you out.The code means you have a defective relay on a control board, Hence you need to have a board replaced. You do have a expensive unit, I suggest you contact a service company. ... Vacuums

RE: Goldstar dehumidifier: Model #DH404EY6, S/N 602TAQP05412 My unit is ~4 yr. old, has worked w/o problems until now. It will no longer auto. turn on. When I manually turn it on, the motor turns on, and then immediately shuts off, and "01" appears on the LED screen for humidity level setpoint. Is this an error code, and what does it mean? Can the unit be repaired? Thanks, Wolfgang


... Vacuums

F-4 error code on microwave - Vacuums


What kind of microwave is it? ... Vacuums

I have a Wertheim 4808 Barrel vacuum cleaner that has suddenly stopped working. I believe that there is a problem with the electrical cord connection inside. I have tried unsuccessfully to open the compartment that leads to that area. One side unscrewed with a phillips head screwdriver but the other side seems to have a different type of fixing screw that I am unable to undo. It is awkward to get at and in a deep slot and the head of the fixing screw? is not visible.


... Vacuums

My polti steam cleaner is leaking steam when it reaches its ready stage. i believe that the threads on the safety cap may be worn . can i get a replacment part for this problem


... Polti Vaporetto 2400 Canister Steam Vacuum

My roomba 550 is having an error code 3. I change the power supply and the problem still. I will appreciate your answer


Your error code is a charging fault code\015\012By clicking ojn the link below is a chart of fault codes. Save this useful chart for further use later\015\012\015\012\015\012\015\012\015\012 ... iRobot Roomba 550 Vacuum

Surpresso S75 Error code 8 is on display. Switching off for 10 seconds or more as suggested in the manual does note solve the problem


... Vacuums

I want to get my XL-5000 singer sewing machine to work. It does not sew. The top thread will not pick up the bobbin thread for one thing and the other problem is that it gives me a error message saying incomplete threading.


Check if there is any thread in the bottom bobbin and next remove it and give it a good clean in its surrounding area.Oil surrounding mechanism carefully and manually push the top needle in and watch the bobbin spinning a see if it tried to pick the ... Vacuums

Wine cooler has error code on bottom half "E4". What are the possible problems?


Sound like a problem with the fan unit; the connectors to the fans get moisture in them and corrode. Just stripping the wires and hard \015\012connecting them, only tool needed is a phillips screwdriver. There are\015\012 3 conne ... Vacuums

My Hoover vacuum is not vacuuming the carpets or floors. When I release the tube to use the smaller end the suction works perfect. So i believe the problem is in the rods on the floor or in the part that vacuums the floor! Can you tell me how to fix it , or where can I take it to get it fixed? thanks


Ive just had the exact same problem. In the very back lower portion of the vacuum You will need to take it apart. I guarantee there is a clog. You might also check your belts to make sure they are still on track. ... Hoover Vacuums

My Janome Harmony 8100 will occasionally stop and give me a System Error #1 - I cannot find anything about this error. It is a computerized machine with 70 stiches and attachable embroidery hoop. I first started getting this error with the hoop and now get it when I am just sewing. As soon as the needle goes down to the bobbin, I get the error. The machine freezes and the only way to get rid of the error is to turn the machine off. Sometimes I can get the machine going again, but now it wil


... Vacuums

Error code #7 and error code #4 and error code #2 shifting mostly code 7 error bumber but nothing is wrong with that...


... Electrolux Trilobite Vacuum

Suction problem I have a Hoover Widepath Fold Away, 12 amp motor vacuum cleaner and the problem I am having is every time I vacuum, the vacuum gets clogged up with carpet. I am probably only able to do one stroke then it gets clogged and I have to stop and unclog it or it spits it out on the carpet. This is very frustrating and I don't get much vacuuming done. Please can you help me. Thank you. Gwen email is [email protected]


Get rid of the carpet its shredding and falling apart.no sence in vacuuming old rotten carpet.or try using a vacuum without a brush roller and just suction ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

List of Error codes


Try this linkhttp://www.singerco.com/uploads/download/4d21c05afe30ff8016e7eadbb35790dc0bf839b4.pdf ... Singer Futura CE-250

I have a Chamberlain Liftmaster Professional 1/3 hp garage door opener. I'm unable to find the model number, but it was made in April 2004 and has an orange learn button. It has been working fine since it was new, but now will not open or close when the code is entered on the touch pad. When the problem first started the door would close, but not open. I have tried to reprogram a new digital code, but it does not work at all. There are no problems when opening or closing the door with the re


... Vacuums

SubBrand name 'Exmork', 5 Kw Sine wave inverter Intermittently, breaks into a spurious mode which causes it to draw excessive current while the output waveform becomes seriously corrupted with severe transient spikes close to the crossover point. We have available oscilloscope images showing the problem graphically. We have four of these inverters out in the field, and they all exhibit the problem from time to time. The fault has precipitated failures in the Power-board module in two units


Had similar problems with my inverters a while back tried to sort it out myself all to no avail. Eventually found out it was a problem from the manufacturers and all that were produced had the same fault. Had to change my brand to Su-Kam inverters. I ... Vacuums

I am located in Trivandrum. I have a britelite " Impact Halogen" torch bought from Dubai two years ago. Recently, have problem in recharging. When I recharge it - not getting recharged. Immediately it gets down the light.Then I have changed the Cell and it worked for sometime and agin the same problem arise. Could you help me on this.


... Vacuums

Hi i hae a star product whipper sniper and i cant get it to go i hae spark i hae fuel but it seems as if there is no fuel getting to cylinder i think it is a problem with my carby the serial no is fcb12071 please help rectify my problem cheers


One thing that you can try is to remove the carb from the unit and spray it down with carb cleaner -- maybe it is blocked (?),,, one more thing to try would be to see if it will fire using ether. there could also be something wrong with the fuel dia ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0587 seconds