Having problems with your Vacuums ?

Bissell 7700 series, pro heat all rounder. Won't spray water. Have checked the line from the unit to the spray nozzel and all seems clear. Water doesn't seem to be flowing from the tank to the end of the unit where the hose connects into. What could be the problem? Any assistance would be greatly appreciated. Thank You. Steve


Answers :

Hello

Grasp the cleaning solution tank, and remove it from the machine. Reinsert the tank into the machine, making sure it fits snugly in the machine. If the tank is even slightly dislodged, water cannot get into the machine. Visually inspect the siphon tube located on the tank to make sure it is not being pressed between the wall of the carpet cleaner and the tank.


Tilt the handle of the carpet cleaner downward until it rests on the floor. Examine the bottom of the machine. Remove any visible carpet fibers or hair clogs that are stuck in the water nozzles.

Push the nozzle cover downward toward the machine wheels to remove it. Then, pull up on the spray tip itself to remove it from the machine.

Soak the spray tip in a sink full of warm water for five to 10 minutes to clean any clogs from the nozzle holes. Dry off the nozzle tip with a towel. Reattach it and the nozzle cover back onto the vacuum.

Fill the water tank with water until it reaches the fill line. Fill the dirty water tank with clean water until it reaches the maximum water line. Plug the machine in, and turn it on. Press in on the trigger, located in the handle, for 60 seconds to try to force water through the system.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bissell 7700 series, pro heat all rounder. Won't spray water. Have checked the line from the unit to the spray nozzel and all seems clear. Water doesn't seem to be flowing from the tank to the end of the unit where the hose connects into. What could be the problem? Any assistance would be greatly appreciated. Thank You. Steve


HelloGrasp the cleaning solution tank, and remove it from the machine. Reinsert the tank into the machine, making sure it fits snugly in the machine. If the tank is even slightly dislodged, water cannot get into the machine. Visually insp ... Vacuums

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Search for bissell pro heat pump. bissell.com will not have it ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Pump part number is 2107181, the diverter valve # 2136988. You can Bissell and they can tell you who may have parts near you, or you maybe able to order thru Bissell.com. Before you took it apart, were you getting water to spray out of the hose. I ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we've taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can't seem to figure out how to get in there to replace that hose....any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Bissell Pro Heat Pet will spray water but not pick it up when cleaning the carpet. Is there anything I can do to fix it? The furniture attachment hose picks up water well. It seems like it could be a bit more powerful of a draw on water. I don't know it that has something to do with why the floor cleaning sucktion doesn't work. Thank you for your time. Jenn


Normal\012 0\012 \012 \012 \012 \012 \012 \012 MicrosoftInternetExplorer4\012 \012\012\012\012\012\012 /* Style Definitions */\012 table.MsoNormalTable\012\011{mso-style-name:"Table Normal";\012\011mso-tstyle-rowband-size:0;\012\011mso-ts ... Bissell Vacuums

It will empty the cleaner but will not spray water filter is clean spray heads were taken off & i could blow threw them is it a case of no prime in pump if so should i fill pump i had this thing all apart and i now know evry inch of this matchine when i pull the triger it sometimes will spray for a sec.but thats it i also took the switch out and air goes threw when i press the switch if it is the prime in the pump how can i fill the pump . what hose on the pump will prime i thankx for your advic


The problem is most likely that your pump belt is worn, stretched or broken. Here you can get the belts you need and view the manual:htt ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

New 50 pint frigidaire dehumidifier won't drain via attached hose , only collects water in bucket and this is a pain! How is the hose supposed to be connected? Seems strange to just screw it into the back of the unit; am I missing something?


... Vacuums

We have inherited a Filter Queen Majestic Triple Crown Model 99C vaccum and have no owners manual stating the year it was purchased and parts available. Our power hose electic wire connection (about 6 inches long) which plugs into the main unit is split in the hose attachment end. The motor sound went instantly quieter and I wondered if this was why when I found this frayed electical wire. It has not been used since this problem was found. How much is this single replacement part? I live


... Vacuums

I have a Bissell Proheat model 7901. When I pull the trigger on the handle, there is no water flow. The brushe revolves and the unit vacuums any water spilled on the floor. Could it be a failed pump or kink hose or ? Thanks Zap


Take the handle apart and put spring back into place. ... Bissell Vacuums

I have used my Steam Vac for carpeting, but until today, had never tried cleaning upholstery with the spin-scrub brush. I spent a miserable afternoon trying to control the spray, which seemed to go everywhere AROUND the furniture, but not ON the furniture! Additionally, I never did get the water into the recovery tank, despite many attempts to connect and re-connect the hoses and recovery tank/lid.


I can sympathize. My vac came with two handheld attachments. I have better luck with the handheld attachment that doesn't have the spin-scrub pads. To keep the water from going all over the place, you need to keep the part the you hold only about 1 ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a tear in the hose of my old model # F6030-900 unit which doesn.t allow water from the attachment to **** back into dirty water bucket. The model #F6039-900 is the same model # but different year I understand. The tear is at the bottom where set the recovery tank in the lay down position and can look in the unit at the bend of the hose.


You will have to replace the hose asm. You can order online at: \015\012http://vacuumsuperstore.com/F6019.html\015\012\015\012H-90001334 (43 ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

The hose on my Samsung 9048R is torn partly from the swivel base. The main problem is that the carpet attachment with the beater bar will not operate now. My brother checked the connectivity at both ends of the hose and there is juice at the bottom swivel part but at the other end of the hose where the carpet wand plugs in it is dead. is there any way to fix this? How does the wire go up through the hose? I have looked around on the internet and it would seem that the entire hose assembly is


... Samsung Quiet Storm 9048R Bagged Canister Vacuum

Have a canister model Lux5500-ser#F35365B and power nozzle number N115Q-problem: The power nozzel does not stay completely connected to the hose-there seems to be some slipage where the hose connects to the nozzel-preventing a solid connection and the unit from working properly. I tried to tighten the connections on the nozzel, but this has not helped


... Electrolux Guardian Bagged Canister Vacuum

DC07 DYSON REPLACEMENT HOSE. HOW DO YOU REMOVE IT FROM THE HANDLE. I have a kenmore whispertone 8540 canister vaccum. The electrical wires (3) to power the beater are embedded in the hose, in a spiral fashion. The yokes that hold the hose on both ends (and attach to the beater on one end and the unit on the other) have no screws or pressure latches; i don't want to use brute force as i may damage the attachment device inside the yoke. If someone can tell me the trick to get these yokes off each


Should be a pry off dot on the underside revealing a screw ... Vacuums

ShopVac pump The waterhose connection is up high. The only way to get the water up to the level of the hose is to continually hold down the on button due to the automatic shut off after it fills to a certain level. On the bottom of the filter there is a hole. I am thinking there should be a small hose of some sort to put into that hole that would then lead up to the level of the water hose. Concept makes sense to me. But in the meantime, good old duct tape seems to have done the trick. Not exact


Hey thats great whatever works its what makes america great ... Shop Vac 584-06-00 Canister Wet/Dry Vacuum

The unit (9400-3) is not spraying water from the lower deck but will spray from the hand held wand. Checked water levels and water/soap dispenser valves which seem to be working fine. Spray nozzles are not blocked. Where do you look now.


Same problem i have got, spent one day on the bloody thing but of no use, the only solution is to spray water from bucket and use the cleaner to **** it up. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The unit sprays for the first few seconds after I turn the unit on and then stops spraying any water or solution. I turn it off, wait a few minutes and the same thing happens. What is going on and how can I get it to work properly?


This sounds as though the pump belt is slipping. This may be caused because the pump belt has stretched slightly or the pump is seized and will not turn. Remove the pump belt and turn the pump rotor with your fingers to see it turns freely. If ... Bissell 7901-R Clearview Proheat Plus Upright Vacuum

Little green machine pro heat pet the collection tank wasn't collection and dirty water was coming out of the bottom. i took it apart, cleaned it up and put a new "duckbill" gasket in. then it quit spraying, but i think i got that working again. now after i spray and get a good foam on the carpet, i switch to suction and it seems very weak. i can see the water moving (trickling) from the head into the hose but it is not reaching the collection tank -- actually, i am not sure where its goin


... Bissell THE BISSELL LITTLE GREEN MACHINE Vacuum

My Bissell carpet cleaner will not spray water out the bottom but will spray water out of the hand held thing. What could be the problem and how do I fix it


Hey here is a guide on how to fix your problem.\015\012http://newzealand.bissell.com/images/In ... Vacuums

The tool attachment for the hose on my Bissell ProHeat 2X CleanShot won't spray soap or water. The bristles on the tool rotate without a problem and the suction is working fine, it just won't spray water when I pull the little gray trigger on the tool.


Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a kenmore vacuum cleaner model # 116.23612. When the hose is attached to the canister it runs, but if you remove the head to just use the hose the unit stops working. Is the motor dead or is there some type of reset or fuse. Could you please tell me how to test this. If so could you please send me instructions on how to replace the motor. Thank you in advance for your help, Tony


... Kenmore Vacuums

My Bissel ProHeat carpet shampooer is not spraying to the floor. I have checked the hoses best I can and they appear to be clear, no clogs. The nozzles don't looked clogged either. The above floor hose does spray water. I definitely have not gotten my money's worth from this machine. Any solutions?


... Bissell 9200 Upright Vacuum

Unit does not spray water for deep cleaning. One can hear the motor running of the ''spray'' action, but no water comes out. I have followed the DVD instructions exactly. Please advise Thanks Anne


Sounds like you have an air lock in line before motor. turn unit upside down and disconect hoses. reconnect and try again with plain water. good luck ... Vacuums

Bissell proheat pet 8910 series won't spray any water from the base but it sprays water from the hose


... Bissell Vacuums

I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet


Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn't blocked as well. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1052 seconds