Having problems with your Vacuums ?

How can i fix my wahl cutek ceramic hair straightener


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How can i fix my wahl cutek ceramic hair straightener


... Vacuums

Everytime I turn my straightener on I get the burnt hair smell been using straightener for 1 month


... Vacuums

My vacuum is making a loud noise like I sucked up somehting I shouldn't have I have cleaned all the hair and made sure there was nothing else stuck in there but it continues to make that loud noise is there something else that will cause it to make this ugly noise, and how can I fix it


... Dyson DCO7 Upright Vacuum

The vacuum picks up dust, dog hair, etc. but then spits it back out when I turn it off. I have taken apart the cylinder in front to empty it and remove any clogs, but that hasn't fixed the problem. I am very frustrated.


The problem is in the hose. Take the hose off and take a broom handle and stick it down the hose. There is something caught in the hose I bet! ... Kenmore Quick Clean 30012 Vacuum

My hair blow dryer works but not blowing hot air...only cold, how can I fix this problem


... Vacuums

I was in the midst of vacuuming with my Dyson Animal when it stopped working. It smelled as though part of the motor burned up (there was hair and string wrapped around the brush so I stopped to remove it). Any ideas on an easy, quick, and inexpensive fix? Thank you!


Hi there,For guidance on clearing any remaining threads or hair from around the brushbar and resetting the machine, please follow the steps shown in the video below. Please note, the brushbar will never rotate when your machine is upright, so ... Vacuums

I can see the height adjuster under my Bissell pet hair eraser vacuum, but it doesn't adjust. The parts don't look like they're touching. It's been iffy since I took it out of the box. Now it doesn't adjust at all. Used only five times. Looks like I should be able to fix it myself. No local repair available. Could you help please?


Http://uk.bissell.com/images/UserGuides/3920E_508.pdf\015\012\015\012This is the pdf manual. If you look at page 12 you'll see that the bo ... Bissell Vacuums

No suction I just replaced the bag, and normally after this I have a lot of suction. Now that I have changed the bag I have less suction that I had before. Not even enough to picj up dog hair. I snaked he hose and checked all of the connections. It seems to have an air leak but no amount of tape will fix this. I cleaned the filer as well with warm water and dried it and re installed but still absolutely no suction. I am ready to throw it out! Any suggestions would be appreciated


1, Does the blower (discharge) side blow bunches of air??Yes: Something is clogged from the bag to the hose end. Try blowing out the hose from the discharge side.Or: The bag is not properly seated. Make sure that the plastic piece is ... Kenmore 23313 Whispertone Bagged Canister Vacuum

DC25 does not suction when in use? Any ideas as to how to fix it?I removed all hair that was in the rollers and still no suction.


You probably have a blockage in the machine. Call the Dyson helpline to troubleshoot a blockage. They now what they're doing, they'll find a solution for the problem. ... Dyson DC25 All Floors Bagless Upright Vacuum

Lately, my Kirby Ultimate G has been acting funny. When I push it forward, it's fine, but when I pull it backward on the carpet, the light on the front flickers and the power flutters off an on. I thought it might be the rollers, so tonight I turned the machine over and pulled out the hair that was wrapped around the roller. However, that did not fix the problem. I should probably backtrack a little bit. In the past, I have had problems with the vacuum running over its own power cord.


The cord will need to be replaced with a cord made for the machine, as it has a non-standard plug. The cord cover is held in place with a # 20 Torx screw. Remove the screw and push the cover gently from behind to unlatch it. The handle must also be r ... Kirby Ultimate G Bagged Upright Vacuum

I have 2 wahl hair clippers (homecut) I require size 6 comb and size 9 comb the model No is 441-3411 and 441/0359 has the base plate blade broken, Where can I source past and replacement base plate blade


... Vacuums

Is there a diagram/picture to help me visualize how to put cleaner belt back in vacuum? I was taking base of vacuum apart so I could get rid of hair that were wrapped on the roller. The cleaner belt came to loose and I could not figure how to fix it back. the model is eureka upright bagless series 430


Hi,Sorry to hear your belt fell out. Not good if you've never replaced a belt before...Here is a website where you can read a detailed description of how to change a belt: http://www.ehow.com/how_8034505_eureka-belt-replacemen ... Eureka 431A Optima Bagless Upright Vacuum

Remington Cordless Salon Hair Straightener I don't know if I should charge it when it is set 'ON' or set 'OFF' ? Lost the instructions but seem to remember it was a definite one or the other. Thanks ahead, Ann


Charge it after use ,, allow the battery to go down almost fully , then charge it . this will prolong the life of the battery ... Vacuums

Hoover windtunnel u6476-910. Brush does not roll. Flat belt and other belt are good. The other thicker belt (called V belt?) does not have tension with the brush roll. How do I make sure it is engaged? Is there a fix? Settings are in "Carpet", "Roll-on", etc. Cleand all hair and bags/filters already.


These machines had a defective switch and a bulletin was sent out to all service depots. If you contact any Hoover Warranty Depot, they will replace the switch, wiring harness and tool receiver under a no-charge warranty. It doesn't matter how old it ... Vacuums

Dog hair gets caught all the time in the belt drive spool, is there a fix for this other than having to pull it out all the time by hand? I have replaced the belt and the brush but this hasnt solved the problem and the belt moves so slowly and I get the loud whining/grinding noise too.


It could be either the clutch, the beater bar or the brush housing. I have included links to each parthttp://platinumvacuum.com/dyson-dc07-dc14-clutch-assembly-900252-04.htmlhttp://platinumvacuum.com/dyson-dc07-dc14-brushbar-assembly-9041 ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Stuck Roller Same problem here. I think in our case, the accumulation of hair and the increasing resistance the hair created over time caused the hair to start melting, and eventually the end cap was stuck to the roller, which prevented the roller from turning. I cleaned out the melted hair(?) as best I could, but I think I need to order a new roller and end caps.


Befrore you plunk your $ down ...\015\012\015\012I dont now that you melted the hair so much as you may have an accululation of gunk and hair. If there is a good (not 'fast food' type) auto parts store near you, go there and ask the cou ... Electrolux 1910 Bagless Upright Vacuum

I have dyson dc28 animal brush not turning how to fix


... Dyson DC28 Animal Bagless Upright Vacuum

Wanting to clean dog hair and dirt from my bissell proheat


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=608457\015\012Generic problem for all Vacuums\015\012Wanting to clean dog hair and dirt from my Bissell...\015\012 ... Vacuums

Have dyson dc17 and spindle that belt fits on keeps getting clogged with hair


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My new pet hair roomba works great except it leaves lines of pet hair along edges of furniture and circles of pet hair around table legs


... iRobot Roomba 560 Robotic Vacuum

My Bissell BS3920F upright (similar to the 10N6F) has been working wonderfully for the past 3 years but suddenly seems to not pick up dog hair as well as it used to. It has been pulled apart by my husband to ensure nothing is blocking the hoses etc and when running the suction seems to be there. It seems to grab the dog hair and leave it in a straight line directly under the unit without picking it up. I then disconnect the hose and use to hose to pick up the dog hair. This works well but obviou


Check to see if your brush is not worn down, they do wear with age - compare the length of the bristles with a new one. Replace the brush ir there is a significant difference in bristle lengths. Also check the flexible ben ... Bissell Vacuums

I have a Lift Off Pet Bagless upright and ever since I **** up a hair tie it hasn't been **** up the dog hair from my carpet. I have gotten the hair tie out of the vacuum but it is still not **** up.


Check the rotating blades. If they are bent or out of synch, then you have to replace the blades, even the motor. ... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

My wind tunnel had a lot of dog hair at the intake hole from my renter that used it. I was able to remove it, but is it possible there is hair up inside beyond the hole & how would I remove it? it is not picking up dog hair .


I have an upright Dyson Cyclonic.  Because I have dogs, I also have a Miele Pull-along.  I use the cyclonic for fine dust after picking up the hairs with the Miele.  Much quicker in the long run.  Otherwise ... Hoover U5453-900 WindTunnel Supreme Bagged Upright Vacuum

Lift-Off Pet Hair vacuum doesn't lift off pet hair!


Very light "stuff" like dog hair will get stuck to the filter since that is where the suction goes. it's primary purpose was to keep dust out of the motor. This is a problem with many "bagless" cleaners. A bagged cleaner keeps all dirt and hair away ... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

My Hoover vacuum is not vacuuming the carpets or floors. When I release the tube to use the smaller end the suction works perfect. So i believe the problem is in the rods on the floor or in the part that vacuums the floor! Can you tell me how to fix it , or where can I take it to get it fixed? thanks


Ive just had the exact same problem. In the very back lower portion of the vacuum You will need to take it apart. I guarantee there is a clog. You might also check your belts to make sure they are still on track. ... Hoover Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0293 seconds