Having problems with your Vacuums ?

Malfunction 8 franke flair. I have removed the brewing unit o rings to free up the drive. Drive motor keeps over running the top and bottom limits hence gears grinding. Could it be the sensor on the back of the motor? What is it measuring? Any help appreciated

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Malfunction 8 franke flair. I have removed the brewing unit o rings to free up the drive. Drive motor keeps over running the top and bottom limits hence gears grinding. Could it be the sensor on the back of the motor? What is it measuring? Any help appreciated

... Vacuums

I noticed the Roomba's brushes were not sweeping, or turning so they could sweep. There was a new sound coming from the machine, the sound of grinding nylon! Upon inspection, I determined the problem to be a heat melted gear support hole. The hole was no longer round but oblong. You could see a ridge of plastic around this hole. So melting I believe was the culprit. The gear that uses that hole was then able to tilt to one side, thereby allowing the gear to disengage from the drive train. I

Be sure to keep your brush bearings clean. If they get clogged, the brushes don't turn and the drive sockets can get damaged. ... Vacuums

Bad Motor I have purchased two of the Kenmore direct drive beltless systems with Progressive systems. The first died after a year, the vacuum motor start making a grinding noies. I pulled the side HEPA filter and could see a fine coating of graphite like dust. Took it to a vacuum repair shop. They said the brushes were going and thus the motor was shot. I liked the vacuum and bought a second, 1 year later the motor is making a slight noise that and removing the HEPA filter I find a slight metall

That dust is from the carbon brushes on the motor. You may need to check them, and also clean out the motor compartment. A slight noise could be a motor bearing starting to go. Does the smell like rubber or electrical. If rubber, then the belt h ... Vacuums

Roomba My Scheduler started making a "grinding" noise every now and then until one day it just started grinding and then stopped (I could restart the unit, however it repeated the grinding and stopping). I have checked the wheels and all of the gears appear to be in good order. I have a hunch the brush motor may be stripped. Any opinions? Thanks: RAnderson

Hi!\015\012\015\012Further investigation (running diagnostics mode) revealed the impeller (in the dust bin) was out of whack. I got another dust bin from EBAY and replaced the impeller and motor. Unit works fine. ... iRobot Roomba 4210 Bagless Robotic Vacuum

We have a hoover porta vac. that at first it would sometimes come on and sometimes not. It did completely stop coming on, so I have changed the switch and the cord but with no luck. Could you offer any suggestions or is this a motor situation. To my knowledge the motor was not making any noise. Your help would be greatly appreciated. Thank You, Molly Maid of NW Fla.

If this has had heavy use, the carbons in the motor may be worn. ... Hoover CH30000 Bagged Canister Vacuum

Hi., If anyone could help it would be greatly appreciated, I have a Flair 3055 ventalation system in my house and over the last five years two fan motors have gone bad. it has been mickey moused together by a local repair man, and as of last week, it has died again. At 4-5 hundred a pop I would like to fix it myself, can anyone suggest a good replacement motor that will fit and work. My honey has breading problems and at this time of year, every penny is allocated, so time is of the essence. t

Hello George, Sorry about your predicament. Various fans are available for your unit but since you say the unit has been mickey moused together adjustments must have been made to the fan seating and system therefore if you order any particular fan th ... Vacuums

Dyson DC04 is making a grinding sound & smells of burning. Hi. I have been told that the above is due to the carbon motor brushes burning out. The brush at the bottom still turns ok. I have bought 2 new carbon brushes & wondered how I would go about replacing them. Any help would be much apprecieated!

Hi there SmartAlec from NelsonVacuums.com.au here, this is not a repair for the faint hearted. First i am assuming you are not using a clutch model - with a selector for ca ... Vacuums

Hi, I appreciate your wiring diagram for the Oreck XL motor --but it is too small to read. Could you send me a readable copy. Thanks very much for your help! Nels Klyver

Print out the diagram u have, then scan it and blow it up to a larger size (all scanner allow u to enlarge the image), this is what I do with hard to read electrical diagrams. ... Vacuums

Bissell proheat 2x 9200 series carpet cleaner. I need to remove the Brush Drive motor. However, this series has the gear end of the motor shaft poking out a hole on the left hand side. I removed the retaining washer and pin from the gear shaft. I need to get the gear off of the shaft in order to remove the motor. It's not budging. How do I remove the gear so I can pull the motor out of the unit? Thanks .

Chap, I wish someone had answered this. I'm having the exact same issue. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Motor whined loudly. Vacuum failure. Suspect motor failure. Hoover.com doesn't list a replacement motor. Drive also failed - could be secondary belt HOOVER U6323- Power Drive Bagged Upright Regards, Jeffrey

Hello, funI was trying to help you out here. Maybe this will help some? I was going back to some customers that asked questions in the recent past and even farther back. It appeared that no one answered some of them, So, I thought I ... Hoover U6311-930 Power Drive Bagged Upright Vacuum

I have a kenmore vacuum cleaner model # 116.23612. When the hose is attached to the canister it runs, but if you remove the head to just use the hose the unit stops working. Is the motor dead or is there some type of reset or fuse. Could you please tell me how to test this. If so could you please send me instructions on how to replace the motor. Thank you in advance for your help, Tony

... Kenmore Vacuums

SEBO Sensors Where are the SEBO X4 sensors, I have taken this apart and not too sure where the sensors are. In particular I get Replace Roller coming up, but roller seems fine and it goes round ok if I disconnect the PCB. My unit turns on spins for 10 seconds and then brings on light C. Just replaced the motor on it about 4 months ago so not too keen to get a new one. Any help welcome.

... Sebo X4 Bagged Upright Vacuum

Motor started making a grinding sound and has a burn order. I found a site that sells parts such as motor assembly but I can not find a repair manual to provide disassembly instructions. It does look like this is a direct drive unit, that is no belts, at least none that a user can relace.Know of any repair manual sites? It is a Hoover F5899-900 SteamVac

... Hoover F5899-910 SteamVac Vacuum

Belt drive Not only do I need a PN for the drive belt on the Panasonic MC-V7395 Vacuum Cleaner, I've noticed that there are problems with the belt breaking. Can someone also explain the proper way to install the belt over and around the motor spindles and any other information that may help. Thank you.

Http://www.partstore.com/Model/Matsushita/Panasonic/MCV7395.aspx?SearchTerm=True ... Panasonic MC-V7395 Vacuum

Hi, I have Fisher & Paykel dishwasher # DD603-BK-USA. When it start to work, it becomes too noisy with a sound HUMMMMMM... I found water desn't spray from the blade. I am possitive that it could have some rust around there. I tried to reach the motor, and I cannot. May you help me how to reach the motor so I can check it.?

There is an access panel by the floor,some are just clipped on,some are fastened with screws,the motor is inside this lower area,but is is quite cramped for working space so you may need to remove the motor from the unit for testing ... Vacuums

Could any1 help me with a nokia 3390, need an unlock code for it, any help much appreciated it is locked to the t-mobile network uk

... Vacuums

I have a NUTONE central vac, when I turn on the power, It sounds like its grinding glass and doesnt suction. Could it be that broken glass got caught in the motor and all I need to do is clean it, or is this the sound of a failed motor?

More likely it's something in the fan. However, I suggest taking it to a vacuum repair shop to make sure. Something could have got into the fan system and is making a racket, but the motor itself won't crunch up glass. ... Electrolux Central Vacuum

I'm trying to find a part number for the motor on a 113296200c, craftsman wet/dry vacuum. Sears could only provide part number 09 113826404 for the model number 113296250c. I have found motors with the model number 826404 on ebay, however no one can confirm if this is compatible. Can anyone help me out here?

... Craftsman 17026 Wet/Dry Vacuum

Low suction Have a Powr-Flite PF 18, suction is good at motor, but low at where hose comes out of top of vacuum. Could new lid seals help the problem? Where can I get new seals for this model. Also my zip is 98801 and my shop is not listed, could you add it please? Sew Creative 1139 N. Princeton Wenatchee, Wa 98801 509-663-5516 Thanks, Lauren-Sew Creative

Replacing the motor cover solved the problem, it must have been warped and was letting suction out thru it. ... Vacuums

Good evening, I have a Xio Z1010 electrolux vaacum cleaner and I hope you'll be able to give me some advice. The vacuum cannot be started. Last time it started for a few seconds and stopped suddenly. Something similar happened long time ago but that was due to overheating. Once cooled down in few hours it would start again. It is not the case now after 24 hours. Could you give me any idea what could be the reason? Your help would be much appreciated. Adorian

... Electrolux Vacuums

Riccar 600FA hook drive gear

... Riccar 8955 Upright Vacuum

Kenmore 116.23513301 Motor runs, but the brush will not rotate. Every time I hit the overload reset button, it will rotate for about a second then stop. I replaced the belt and cleaned around the brush, but the brush still will not rotate. Any help you can give me would be greatly appreciated.

If the motor on the power brush is running the belt is bad, if the motor on the power brush only runs when you push the overload, the overload is bad. ... Kenmore 22812 Bagged Canister Vacuum

I have an older model Bissell rug shampoo machine, model # 1631. I have several bottles of Bissell 5 One carpet formula to use in this machine, however I have lost the measuring bottle that tells me the amount of soap solution to use per 64 oz. bottle of water. I sure would appreciate if you could help me.

I have a older mod. Bissell carpet machine plus mod. 1630-5 and need a floor nozzle part num.013-6194 and grip tube w/button part num.014-4181 and trigger part num.010-9406 and tube ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

I have an old oil lamp. this motor/pump pumps mineral oil up a tubing and then the oil drips down the fishing line for lack of better word. and the pump does not work. On the motor itself it reads UPPCO, Inc. Chicago Model 50 Impedance Protected 120v-60 hz .30 amps P-8365-1 Use sonneborn mineral oil only do NOT use water. Any help would be greatly appreciated. Thanks Shelley

... Vacuums

Burning smell coming out while using a Hoover's upright vaccum cleaner (model U6434900). Replaced both flat and v-belt. The problem appears to be coming from near the motor area. The manual does not provide any information on how to reach that area. Any help will be appreciated.

Took it to a manufacturer's repair center. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1053 seconds