Having problems with your Vacuums ?

My Panasonic MC-E3001 vacuum cleaner works for a few minutes & then cuts out. I changed the bag & it worked again for 2 minutes but then cut out again.The pipe that sticks out of the side has a clip on it but it doesn't seem to be holding anything.

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Panasonic MC-E3001 vacuum cleaner works for a few minutes & then cuts out. I changed the bag & it worked again for 2 minutes but then cut out again.The pipe that sticks out of the side has a clip on it but it doesn't seem to be holding anything.

... Vacuums

My Mom has a Dirt Devil Featherlite and the belt falls off all the time. I put it on three times today and it falls off within a few minutes. The belt post I put it on doesn't have anything to hold the belt on. Is there supposed to be something holding the belt?

It sounds like the belt is too worn and loose to stay on. Buy a new belt specified for that model of vacuum and install. Ensure that there is only a slight amount of give in the belt when you press the middle. ... Dirt Devil CE6100 Featherlite Upright Vacuum

Dust buster won't hold a charge, even if I let power run down to nothing and then charge it for a full day or two. This is the 2nd dust buster that has done the same thing. When I first take the item from the charger, it appears to have a very strong charge. Then within a minute, I cannot pick anything up. Thanks for your help.

... Black & Decker AV1200 DustBuster Handheld Vacuum

Roomba circles My Roomba circles for a few minutes, then beeps 9 times and stops. A red exclamation mark appears on the left hand side of the controls. If you persist in restarting it, eventually I have been asked to clear Roombas wheels. As far as I can see, there isn't anything blocking the wheels.

Yes, this is known issue and if your bumper moves freely, you might be facing a sensor fault caused by poor quality of components.Here is a guide to fix ithttp://www.schneordesign.com/Avi/irobot/roomba_mod2.htmHave fun ... iRobot Roomba 560 Robotic Vacuum

I have a Shark Euro Sweeper, and it doesn't hold it's charge. I only use it a matter of a few minutes and already the green light turns to orange. I was told it would hold a charge for 30 minutes. So what's the deal?

I assume you've had the cleaner for a while and your battery is dying. Batteries can only be recharged a finite number of times and they also suffer from "memory loss" due to not being fully discharged before recharging.\015\012\015\012Ba ... Vacuums

I have a Sleeptight Imetec Electric Blanket with timer and Dual Controls one for each side of the bed recently the timer was set for 45 minutes and when 45 mins elasped it went off and the control light began to flash which is normal however it is since stuck in this mode light flashing will not heat just keeps flashing is there any way of sorting this the other side of the blanket for the other side of the bed seems to be ok although it did the same thing but reset itself any ideas Regards

... Vacuums

Replacement parts... I've got a 3594 Bissell and the belt has come completely off. In the process of breaking, it bent the metal guide inside the motor housing and melted the plastic that holds the guide and keeps the belt inline with the roller. I've got it running again by using a screw I filed all the threads off of, but it only works for 10 minutes at a time before breaking another belt. This process is getting expensive, as it usually takes 30 minutes to completely vacuum the house. Is ther

Most likely it is the top cover that needs to be replaced, part #2031238 and is around $30. It would have that guide on it. ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

I have a dirt devil (ultra vision) it will not pick up anything i dont know what is wrong. It will not pick up dirt through the pipes no pressure in the pipes

Will try to help here.. first off.. regardless of the brand..upright vacs operate pretty much the same way.. I assume that when you plug it in and start it that the motor runs as well as the beater brush on the base.. from the sound of your symptoms ... Dirt Devil Vacuums

Loose wire ive got a loose wire inside my vax cyclonic 1700w and ive stripped it down but cant see anything and its still not working but it was working when i moved the wire from side to side. Please help

Sounds to me like you have a open wire. There is a break in the wire inside to the insulation and as you move it, it gains and loses connection. You can test it with a continuity tester as you move the wire or just replace it to see if that solves th ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

My Dyson DC25 got stuck and wouldn't return to the upright position, I figured out that one side had jumped the track and gotten stuck in the square hole below the track. I did not want to break the plastic to force it back, so I removed the screw on the right side that was holding the kick stand on and removed the kick stand, also a spring thing came out. Problem is, now I have no idea how to re-install the kickstand. Can't find a technical manual or video anywhere, it can't be very difficul

... Dyson DC25 All Floors Bagless Upright Vacuum

Progressive 38613890 The slot on the belt side of frame where the beater bar fits down into a U shaped area that holds it in place has worn and stretched out and does not hold the beater bar in place. Can this be repaired somehow?

... Kenmore Vacuums

Producing steam i just got the shark assembled the mv2010, then it is not doing anything, it vacuumed just fine, but when i put the steam pad on it wouldnt ever produce steam or do anything,it felt like the water was heating up but even after it sat for 20-30 minutes when i pull handle back towards me nothing happens, no lights no steam no nothing, so why wont it work

This link is for the manualhttp://www.sharkclean.com/manual/MV2010_11_IB_ENG_110103.pdf ... Shark MV2010 Vac-Then-Steam 2-in-1 Vacuum and Steam Mop Purple

Have a Centralux Aerus about 5 years old. Don't see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced

There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself ... Electrolux Centralux Vacuum

Electrolux 6985A wheel (the one on the cord side) is sticking. How do I remove it to clean out the hair or whatever is making it stick?

Most of these wheels have a push fit. the larger the diameter the tougher to reach the axle portion, but it generally has a flex cutout on at least one side which you can push in slighlty with a long flat screwdriver. Try spraying with WD 40 or silic ... Vacuums

Dirt devil kone won't hold a charge. Its constantly on the charger but yet won't hold a charge long enough to do anything

... Dirt Devil KONE Hand Vacuum MO213BLU Vacuum

I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge

... Vacuums

Not sucking from bottom into bag, but blows out the side filter,..yet it DOES **** FROM HOSE ATTACHMENT. How can this be?...the.belt is fine recently replace, the rollers clean..I can feel anything i

Here is a diagram ,it's probably the hose behind the brush bar thats blocked.http://www.vacsite.com/en/bissell-parts-1/bissell-parts/3522-powerf ... Bissell 3522 PowerForce Bagged Upright Vacuum

Won't hold charge more than 5 minutes

Dear Patkyle,\015\012\015\012Have you check your battery? Is it working?\015\012Mainly this type of problem arrives due to battery has stopped working. (In may cases it is a case of water clogging, It may happen due to exposure in humid conditi ... Roomba 3005 Pro Robotic Vacuum

The side hose is stuffed up and wont **** anything up

... Eureka Smartvac 4870 Bagged Upright Vacuum

Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn't seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right....can you help. I am v

I've successfully used a compatible belt - Royal 104425001 .It's still new, but for the time being at least - it works. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

My vacuum just stopped working, so I don't know what the problem is. I used it in the kitchen to vacuum the hard wood floor. I turned it off, and a few minutes later, turned it back on to finish vaccuuming the kitchen floor. It just would not turn on. I had not unplugged it or did anything to it. I then tried to see if it would work in another plug, and no luck. I'm trying to figure out if it can be fixed or if I need to look for a new vacuum.

When I get most Vacuums that have dies on people most of them the wire has been worn and cut one or more wires on the plug cord. Sometimes the cut can be over looked. Please unplug and check the wire carefully.Also please post the make model a ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

Oreck vaccum when i put a new belt on, the belt rubs the side of the wall of the vacuum gets real hot and busts. is there any type of washer fitting that goes on the vacuum to hold the belt in place? i dont know i need help thank you. you can reach me at [email protected]

The belt must not be running true to the pulley. You may need a brush roll, but also check the motor to make sure it isn't moving inward after the belt is put on. ... Oreck XL Ultra Bagged Upright Vacuum

How do i remove the front of the Proheat Clearview to clean it out? I removed the two obvious screws at the front sides of the clear plastic part but see anything to remove to take it off.

... Bissell 1699N ProHeat Clear View Force Upright Vacuum

When I took the base cover off the vacuum to clean the roller, a metal piece that is bent in half, as well as a white plastic stick piece came flying out. I think it might have to do with holding the vacuum in an upright position, but I don't know where it goes. Help!

They go in the slot beside the right wheel. Metal spring first, (the open ends facing away from front of vacuum base. The white nylon piece lays parallel and directly on top of the metal spring, round edge up, and aligned with the open ends of the me ... Eureka 411A Upright Vacuum

We have several victo lite vacuum.s with pipes that are unusable because the clips that hold both ends of the pip[e are broken and we have spoke to our suppliers who say that they don,t make them any suggestions

I have not solved the problem but i cannot subscribe to your site as i am not in a position to do so the only way to solve the problem is for someone to make and supply these clips easy ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0316 seconds