Having problems with your Vacuums ?

Rear wheels are woobley, and misaligned - Vacuums


Answers :

From what you say, the wheels and axles are probably worn out or the wheels have collapsed. You do not mention the make of the machine, but go to an agent or any large appliance repair depot with the make and model number and they will be able to supply you with new wheels and axles, or be able to order them for you.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Rear wheels are woobley, and misaligned - Vacuums


From what you say, the wheels and axles are probably worn out or the wheels have collapsed. You do not mention the make of the machine, but go to an agent or any large appliance repair depot with the make and model number and they will be able to su ... Vacuums

I want to open a Hoover S3825 Elite Cyclonic Vacuum to see if I can repair or replace the cord reel assembly. Currently the reel slowly draws the cord back into the canister once it is pulled out. I found the mounting screws under the rear wheels once I removed the hub but I do not know how to remove the rear wheels, everything is plastic. The front screws are under the front caster wheels and I think I need to take a screwdriver and pry off the little cylinder wheel to get to them by rotating


... Vacuums

Eureka Rally 3977B vacuum cleaner rear wheel assembly


... Eureka 6983 Bagged Canister Vacuum

Can the Rear Vacuum Wheel hoover aura II be replaced


... Vacuums

The rear wheels won't stay on my Kenmore Progressive 359235 Upright with Inteli-Clean Vacuum


... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

I have a Kenmore Whispertone 4.8 where the left rear wheel has broken off. Is this repairable? FYI - Buying a new or used vacuum is not feasible at this time


... Kenmore 23313 Whispertone Bagged Canister Vacuum

Remove rear wheels - Dirt Devil Featherlight Bagless Upright Vacuum


... Dirt Devil Featherlight Bagless Upright Vacuum

How to replace rear wheel on bissell cleanview hilex vacuum


... Vacuums

Sears canister vacuum rear wheel won't stay on


1) test the power cord for open, defective, or break use the VOM 2) test the fuse for open, loose wire use the VOM3( tes the motor, for open, short, or defective, need repair.4)test the switch, for open, or loose wires, or short.see h ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Rear wheels keep coming off, - Electrolux Z2256A Bagged Upright Vacuum


... Electrolux Z2256A Bagged Upright Vacuum

Rear wheel assembly on a kirby g3 - Vacuums


You can replace the wheels, they are attached to the transmission. If a problem with the transmission, you may have to replace that. You did not say what the problem is!! ... Vacuums

How to replace rear wheel on bissell vacuum


... Bissell Vacuums

How replace rear wheel bissell 9400? - Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum


Hello,Hi There,Ok, so in order to get the wheel assembly back into the\012 machine, you're going to have to take apart the machine, or at least \012the housing underneath of the clean/dirty solution tank, as well as the \012ho ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I own a Eureka Optima 437 and one of the rear wheels are broken and cannot find parts for this. Where can I find parts for real wheel? I have a rear wheel that came off too. The wheel seems fine, but the plastic base that the wheel clicks onto on the underside of the vac seems to have cracked. I need a new plastic bottom. Any ideas?


Called Eureka Customer Service and ordered another part. They are mailing it to me free of charge!No more problem. ... Eureka 431A Optima Bagless Upright Vacuum

Unbeknownst to me, someone took the bag out of my Kenmore Progressive vacuum and failed to replace it. I have been vacuuming without a bag for months, and today the vacuum stopped sucking. When I opened up the front to replace the bag, tons of dirt and dust came pouring out. I thoroughly cleaned the vacuum, put in a new bag, but still no sucking power. Just dust coming from the rear vents where one of the filters is. Is the vacuum ruined, or is it a simple solution of buying a new filter?


Sounds like you need to buy a new motor. All that grit and dust will ruin a motor and I'm surprised it lasted as long as it did.\015\012This is where a vacuum that won't run without a bag would have been nice. (Aerus for one) ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Oreck XL How to remove rear wheel. Removed all viewable hair, thread, etc., but one wheel is still hard to turn. I think there's hair stuck inside the wheel core. Can I remove the wheel & take it off the metal post?


You can take a medium size flathead screwdriver and slide it in beside the wheel and under the pin. Then pry carefully on one side and then the other it will start to come out but work both sides alternately so you won't put too much pressure on the ... Oreck XL2000 Bagged Upright Vacuum

I have a Eureka Boss Power Plus and the beater bar is rolling, the belt is turning, but after vacuuming up around the litter box (not a lot of litter), when I turn the vacuum off, the litter, or even household dirt, falls out. When I hold the vacuum back to turn it off so that it doesn't fall on the floor, it's sitting in the cubby where the wheels are. The bag is empty, the hose is not plugged, the hose is securely fitted on both ends of the unit. This vacuum was purchased in July and is being


Even though the brush is spinning, you probably need to replace the belt because it is s ... Eureka Vacuums

How to wind cord onto spring loaded retractable cord reel for a Kenmore canister vacuum. There is a metal 'U' shaped, spring loaded, piece that fits over the outer aspect of the wheel. If cord needs to get wound on under this metal band I can't figure it out and the band is like factory sealed onto the wheel. Also. I don't know which direction to feed the cord onto the wheel


What is the exact model # please?Thanks!! ... Kenmore Vacuums

For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.


... Kirby Ultimate G Bagged Upright Vacuum

Hoover wheel assembly replace wheels - Hoover Fusion Vacuum Front Wheel Carriage 93001674


... Hoover Fusion Vacuum Front Wheel Carriage 93001674

My kenmore premalite vacuums wheels pop off - LG Electronics Premalite Vacuum Bagless Cyclonic Vacuum


... LG Electronics Premalite Vacuum Bagless Cyclonic Vacuum

Both of the wheels are wobbly and loose on my Kenmore upright vacuum model 721.37060. I don't see where I can remove them to analyze and fix the problem, which seems to be that the wheels are loose on their axels. How do I get the wheels off and what do you think I'll find inside?


Most if not all vacuums have an access panel on the bottom.It may be held on by a couple of big plastic clips,the kind you squeeze together and it releases a door.Some have plastic screws.There may also be a couple of phillips screws along with it or ... Kenmore Vacuums

How to attach the wheel on a Kenmore Premalite Vacuum Cleaner?


... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Wheels the wheels on my vacuum bunch up, have replaced them and still doing it, also it will not lock in an upright position, something fell off do not have part


The axle for the rear wheels have worn into the cut outs in the body that it goes through and they are rubbing on the wheel wells. This common for this vacuum model , the only real fix is to replace the body assembly. Sears will have to do this, this ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

My rear wheels keep poppping off. I've hammered and glued, but they won't stay on. Do I need new wheels or a new axle assembly?


Greetings,\015\012\015\012You may need to just purchase the the little c-clips that hold the wheels onto the axle. Kirby Vacuums actually have a hub cap on their rear wheels that can be removed to access the axle end with the c-clip. ... Kirby Ultimate G Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0953 seconds