Having problems with your Vacuums ?
How much water should I put in warmer
to keep warm for 4-5 hours what temperature setting should I use. Food is already hot.
- I would use temperature of 160 degrees. As for the water I would use about a cup. This will keep the food good and hot and the temp of the water is below boiling so it will last quite a while.
There is no harm in completely filling the water well in the warmer. I don't know what size you have, but a full size food warmer accommodates 3.5 quarts. About half or a little more than half of the well's capacity should suffice for 4-5 hours. I also have to assume your warmer is thermostatically controlled because a lot of them are, but I don't know if the setting choices are in degrees or what. Assuming that they are in degrees a low setting like 250 should suffice.
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
How much water should I put in warmer to keep warm for 4-5 hours what temperature setting should I use. Food is already hot.
\015\012I would use temperature of 160 degrees. As for the water I would use about a cup. This will keep the food good and hot and the temp of the water is below boiling so it will last quite a while.\015\0 ... Vacuums
Hi, I own a GE 4.8 litre slow cooker. It is very basic. No timer. Therefore, I just turn it off when I get home? It won't count down the time from the highest point of low to the off setting by itself? Also, I am making ribs and have already prepared the sauce. It will be refrigerated over night. Will putting the cold sauce in the warm slow cooker break the ceramic?
DZ9080 IRON IS NOT VERY OLD, BUT HAS HEATING AND STEAMING PROBLEMS. IT MAY BE ALL HEATING RELATED! MY WIFE WILL SOMETIMES JUST LEAVE IT "ON" FOR TWO HOURS AND THEN IT WILL START STEAMING AGAIN. I CANNOT MAKE SENSE OF THE HEATING INDICATORS; SOMETIMES IT WILL STAY GREEN NO MATTER WHERE YOU SET THE DIAL ---- AND IT DOES NOT FEEL HOT! WHEN I TRIED IT AGAIN TODAY, THE SHOT-OF-STEAM WORKED FOR A WHILE (AND THE SPRAY WORKED), BUT THEN ALL IT WOULD DO IS DRIP WATER AT THE TIP WHEN TIPPED DOWNWARD.
I couldn't find any warranty information on this iron, but I suspect that the heating element either has a faulty connection or part of it has cracked, making contact at time, but poor contact at other times. The unit will have to be taken apart an ... Rowenta Vacuums
Bissell will spray water when set to water rinse, but as soon as it is set to light, normal, or heavy cleaning, there is no spray. I have tried priming but to no avail. I put plain water in the solution tank to test without ay success. It is like it loses it's prime whenever you try to use a solution mix. Once you set it back to water rinse only and go through the priming steps, it is OK. Any help would be appreciated. Thanks.
Please check the following with liquid in both tanks.\012 \012- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.\012- Check for ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
My sunbeam water cooler model #YLR2-5-67H3 has been sitting unplugged for 3 years. I moved, plugged it in and put a water bottle on top and water went all over the floor. I unplugged it, (read the instructions on the front, duh) and it still leaks on the floor. What should I do? I put it over the sink, emptied it, checked the drain plug, tried running a glass full of tap water through each tap. Only the room temperature one would work.
One of the rubber connecting hoses inside it has dried and aged so the pressure of the water from the bottle made it burst.\012\012\012You will need to open it, find the defective hose and replace it - a 2 hour relatively easy job. The hardest ... Sunbeam Vacuums
I have a hamilton beach water cooler. What is the temp. setting fot the cold / hot water? why is the water holding compartment get hot?
The cold water - 60F/15C. Hot water - 190F/90C. Both temperatures are set in the factory and should not be changed by the customer or the manufacturer can't guarantee that the unit will work as expected.\012\012\012If by water holding compartme ... Vacuums
My Oregon Scientific BAR888 has 5 windows, 1. temperature, 2. humidity, 3. mb/hPa or inHg (switch at the back), 4. bars showing pressure changes over 24 hours, and 5. time/date. Window 3 gives an option to set something between 0 and 2500. Oregon say they only have one set of instructions for the BAR888 but they do not match my instrument as there is nothing included for my window 3. Trouble is I don't know what the 0 to 2500 relates to and therefore don't know what to set it at.(My model does n
Envirosteamer 300 leaking water. Older yellow model. I put water in it and as soon as it heats up, all the water leaks out the bottom, and it barely gets warm! It worked fine before. Could it be seals need replacing or something? Thanks!!
... Eureka Enviro Steamer 370 Upright Vacuum
The steam do not get hot it get warm athe water
Hi,Sarah, the unit is no good...Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
Do you put hot water in the tank
It would depend on whether you machine preheats the water or not,and what kind of machine,Bissell,GE,etc..If your machine doesn't heat the water,then I would use hot water.Do not boil water,tap is fine. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o
Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
I have a steamvac v i was wondering if i fill the container of water to the top and does the water need to be cold or hot? I heard I could use tide liquid if so how much do i put in the detergent holder
Hi there SmartAlec from NelsonVacuums.com.au here. I have looked at literally hundreds of steamvacs over the years and you can use warm but not hot water in the tank. You c ... Hoover Vacuums
I HAVE A BISSELL PROHEAT 2X HEALTY HOME, IT WORKED JUST FINE THE LAST TIME I PUT IT UP. YESTERDAY, I NOTICED THE FLOW GAUGE WAS NOT SPINNING, SO I CHECKED AND SURE ENOUGH NO WATER WAS COME OUT. I CHECKED AND ALL THE TUBS AND EVERYTHING ARE IN THE RIGHT PLACE AND HAVE LIQUID IN THEM. HAVE TRIED PRIMING CLEANING THE BRUSHES RUNNING HOT WATER THROUGH IT... HELP
Have you made sure that the tanks are seated properly and the red \012(or black) auto-load gaskets are in place. \012Check the bottom of the Water Tank and the Formula Bottle to make \012sure each has a red auto-load gasket attache ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
My brand new bissel little green proheat pet series is spraying solution however it's not hot when it comes out. I put hot water in the tank & turned the heater on. Isn't this the whole point?
Have you checked the user manual? Can be found at http://www.bissell.com/searchresults.aspx?searchtext=little green&mode=userguides\015\012\015\012If there is no element then the water will cool down naturally. ... Bissell 1425 Little Green ProHeat Handheld Steam Vacuum
My enviro steamer was going OK then suddenly just put out water. Then the handle got hot and boiling water started leaking out of the body.
That's a major hardware failure in the unit, there is no simple fix for that. How old is this unit?Tim ... Electrolux Envirosteamer 370A Canister Vacuum
Warm Mist Humidifier EE-LAC50 : the water becomes hot but is not released as a warm mist. Can I fix this myself, or does it need to be sent for repairs?
What country are you in?I have found the parts available for your humidifier and it appears that the part it would most likely be is the lid set.It is a Zojirushi I assume.The cost is $31.70 USD plus S&H probably.I would guess probably $7-$10.If that ... Vacuums
Water leaking When I fill the canister portion with hot water and put it in my machine it immediately begins to leak out the bottom. It has just started doing this. Do I need to take it in for repair?
The water tanks on this unit have had a very bad history of leaks. Most of the repair people had never heard of this unit, but one did, and had a spare set of tanks. If the unit is still under warranty, it is worth your while to get a replacement u ... Eureka Atlantis 2595A Upright Wet/Dry Vacuum
Rowenta Press and Sew Iron w/Teflon soleplate: Dial to set temperature hard to turn for steam. Iron gets too hot when set for steam, fabric burns.
My bissell aroma pro had a horrible burning smell then stoped sucking up water. the motor was still working and water was being feed out just not back up. the machine was hot as i had already cleaned 3 rooms in the house. i let it cool down but the burning prob returned as soon as i turned it back on. any help would be great thanks
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum
I got my bissell for $7.50 from a thrift store, if you can believe THAT. Used it for the first time today after reading the manual online first. After filling the clean water bladder full of hot water and setting everything up the way I wanted, proceeded to turn things on and go for it. Well, the water/solution just kept coming and coming, without my finger on the trigger. Obviously something is jammed in the open position but where? The trigger moves freely.
This is the answer I got from Bissell:Please\015\012check the gasket at the bottom of the tank to ensure it is attached and\015\012not lodged in the reservoir of the machine. If this is not the problem,\015\012take the machine for i ... Bissell 8910 ProHeat Clear View Upright Vacuum
Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the
... Dirt Devil M088905 Vision Bagless Upright Vacuum
After two years, my Euro-Pro Shark Steam Mop, Model S3101, no longer ejects steam. I have used tap water. I think the line is clogged with mineral deposits. The light is on when plugged in, and the unit heats up. I even put in vinegar for about an hour to break up the calcium deposits, but it did not correct the problem. How do I fix it, or, where can I take it locally to be fixed (Orange County, CA)?
Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
I posted my problem earlier today that I was having with my Bissell Little Green Machine not dispensing solution, but sucked up no problem. Someone said that the most common problem was a blockage. We put hot water in the reservoir for 15 minutes as advised and it still will not dispense. The fluid is now ''dribbling''so it is better. It is just not spraying. We are able to blow from the end and make bubbles in the reservoir which shows us it is not blocked. Any other suggestions?
Okay. I fixed this on mine. Undo the screws on the handle, right by the trigger. You pull the tubes off the little valve. Push on the button and see if you can blow through the valve. If not, push a pin around in the valve (with it pushed into the ... Bissell 1720-1 Little Green Wet/Dry Vacuum
My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old
Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
My Eureka Deluxe Enviro Steamer doesn't steam, I had no directions with it so I'm not sure how much water to put in it. It comes out the bottom before it heats up sometimes.It never seems to get hot enough. Hope you can help
You will need to pour two measures of water using the measuring cup or 12 oz of water. The reason why water comes out of the bottom is because the floor cloth is too wet or you had too much water in the tank\015\012\015\012Cl ... Eureka Deluxe Enviro Steamer Vacuum