Having problems with your Vacuums ?

Hi. I bought a delonghi iron stirella. i did all what was wrtitten in the instruction but the button "lack of water" is still on and i have no idea what i have done wrong and what i should do to fix this problem. thanks you in advance, Paulina Rybak

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi. I bought a delonghi iron stirella. i did all what was wrtitten in the instruction but the button "lack of water" is still on and i have no idea what i have done wrong and what i should do to fix this problem. thanks you in advance, Paulina Rybak

... Vacuums

Hello. My scooba 5800 had a check tank light on. I used a straw on the valve and that fixed the problem. Now the scooba runs like nothing is wrong, but there is no actual cleaning going on! It goes the full cycle, but no liquid comes out. The vac part seems to be working b/c there is fluff in the vac when it's done. Please help!

Hello, Take the battery out and hold the switch down for 30 seconds, to reset the curcuit board, then charge back up for 12 hours. this should take care of it. If I can help future please call @ 1561-848-3387 Thank you, Teresa. Clean Sweep Vacuums ... iRobot 5800 Scooba Vacuum

Roaring vacuum My vacuum begins to roar shortly after I turn it on. The sound seems to be coming from the middle of the canister. When I take the recoil cord off, there is a plate just under it still on the canister that is extremely hot. Any idea what could be wrong and how to fix it?

Good day,your problem seem that it is plug if you have no suckiong ,place the hose on the exaust that should un plug the hose,or the motor has had some dirt et it and plug the intake ,that is why it roars try this,later ... Electrolux UltraLux 2000 Bagged Canister Vacuum

My filter queen majestic quit working. I opened up the unit to see what was wrong and I did not immediately notice anything wrong. Upon furter examination I noticed one of the traces on the printed circuit card was burnt. I used a soldering iron to "bridge the trace and it appeared to fix the problem for a while. Now it has stopped working again, and when I jumper the trace to run the motor it seems to work. Should I just replace the card? Or is there a more serious problem with too much current

I recommend replacing the card. Soldering involves the risk of further damaging the card, so it would be useless anyway. Why waste valuable time?\015\012There is a possibility of the motor overheating, generally due to a blockage in the airfl ... Filter Queen Majestic Canister Vacuum

I bought the Eureka 4703D model vacuum and my very first time powering it on, it was extremely loud - abnormally loud, and I don't know if it is loud like that because I possibly put it together wrong, or there is something wrong with it or it was previously damaged and I would like to know if this is something I can fix myself or do I have to take it back apart and return it to Walmart where I purchased it from. When it makes the loud noise, it does vacuum fine but the noise is just unbearable

... Eureka Power Plus 4703D Bagless Upright Vacuum

Continued problem At this point I have hopelessly disassembled the unit and I have no idea how to put it back together I need a diagram or a source to have it done for my. Any ideas?

Remove the rubber strip from each side. Open to access the bag. Slip a thin srcewdriver between the case and the small strip (that runs the lenght of the case) about 3/8 of an inch in. You should then be able to slip the strip out. Be careful whe ... Electrolux Epic 6500 Vacuum

I bought one of these units last year and it worked great for about 9 months and then it stopped brewing coffee. Not sure what is wrong. It will not heat the water to make the coffee. Any idea as to what could be wrong?? Thank you. Pierre

Hi,Either the heating element is completely corroded with mineral from the water or the heating element has gone bad...If it is not heating at all there is some kind of electrical problem or the element is gone bad... ... Vacuums

NO SUCTION My Electrolux Z2274 upright vacuum cleaner has lost it's suction and is very noisy. Have checked and rechecked there is no blockage. Have cleaned the filters. In fact done everything I can think of. Any one know why and how to fix this??

If you have no suction, there are only a couple of things that could cause it. As you have checked for blockage, and changed your filters, you may have a vacuum motor with bad bearings, or broken fan blades (inside/on the vacuum motor). Either sympto ... Electrolux Central Vacuum

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...

The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum


When the vaccum is upright, the beater bar is not engaged. When you tilt the handle back, the clutch engages and the beater bar begins to turn.\015\012\015\012There are two likely possibilities for the "screaming noise". First, and most l ... Dyson Vacuums

When I turned on the sweeper it would not start. I put a different power cord on it and it worked fine. now it won't start but the light on the brush and the bag full will flash when i turn it on and off but it wont start. i have 2 of these doing the same thing. do you have any idea what could be wrong. I have checked for clogs but have found none. Bob

Its sounds to me like the computer board inside the machine has gone bad. Keep in mind that the filters in these machine do need to be replaced regularly to keep the vacuum working correctly. Any good vacuum shop should be able to fix your problem. R ... Windsor SR12 Sensor Bagged Upright Vacuum

Hi,My agitator brush won't run on my hoover S3590, I changed the belt, that didn't work. I don't see a possible cause in my book except replacing the belt. I think there could be a short, the brush will come on sometimes when pulling back and slightly lifting. Any ideas would be great and can I fix it myself? Thank you for any help, Bobbie

Hi Bobbie\015\012Take apart the electro floor head if you can and inspect inside - it may well be that there's clogged dust preventing the brush from turning and also check both sides of the actual beater bar as thread and tangled hair can often lead ... Hoover S3590 Bagged Canister Vacuum

I have a kirby sentria and after I shampoo'd the carpets I put it back together to be a regular vacuum and now it wont turn on. Any ideas what could be wrong?

The only thing I can think of is the brush head is not on properly.If the head is not aligned right,then the saftey switch wont be activated.Otherwise,I'd say the saftey switch or power switch.Did you make sure not to run over the cord? ... Vacuums

I have a Dirt Devil Vision and when I put a clean canister back in place the suction at the bottom of the filter clogs up and very rarely go into the canister. Also where the air blows out of the motor, I will get particals that will blow out. I have checked where the belt is and also the suction tube. Do you have any ideas how to fix this problem?

Yes your intake hose is clogged thats the clear hose you can see it on the bottom from the back.disconnect the upper hose from your intake hose and try to push a coat hanger through with the end of the coat hangers end bent till its rounded so you do ... Dirt Devil M086700 Vision Bagless Upright Vacuum

I have a vax cylinder model V-094. Working fine then started to play up. Switch it on and the motor seems to struggle to power up. Kind of wurrs up and down. Was thinking it could be the brushes have worn. Tokk to bits and cleaned her up, took a look at motot and brushes, cleaned them too, back together and still them same problem. Help please, hoover is not old but has done some work really don't want to through away something that can be fixed.

Hi.\015\012\015\012after all you have done I would be pretty confident its the motor thats faulty they are expensive to buy so machine is going to be scrap,\015\012\015\012Sorry.\015\012\015\012 ... Vacuums

I have the Eureka Whirlwind upright vacuum. All of a sudden there is no suction- the hose has suction but not main part. I have no idea- but the brush part is not turning??? should I get a new vacuum or is this an easy fix? thanks!!!!!

If the belt isn't turning then it has snapped. Check the top of the hood for two or three crosshead screws; two at the front and one under neath by the left hand side if looking at the upright from the front. Its easy to fix if you take your ti ... Eureka WhirlWind Litespeed 5844 Upright Vacuum

I've been using a small shop vac in the seller to vacuum up dust, sawdust etc. I have emptied the inside and the filter looks laden with dust. It does not "****" any longer. What is wrong and what do I do to fix it?

You have to clean the filter too. Use an air hose to clean it or brush it off with a stiff brush or you can wash it if it isn't paper. As a last resort you can get a new one. ... Shop Vac 925-13 Canister Wet/Dry Vacuum

I sucked up the fringe on a carpet, it didn't actually get sucked up but it did disconnect the drive mechanism in some way. Any idea how to fix this?

This vac doesn't have a reset button. You probably have a broken belt. ... Eureka 2971AV EZ Kleen Bagless Upright Vacuum

Motor grind Loud sound and smell on occasion. Started as just short sound as turned off, +/- 2 seconds. Now does it on star up unless I tilt the unit back. Ideas? Is it worth fixing? ns

Try checking the belt, that is probably the smell, might need replacing ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Water Leakage We have a Bissell Proheat (Pro Tech). I don't think it is the 2X model. When releasing the water with the knob on the handle, water comes out the side of the housing at the lower part of the unit. Is their a seal that my be worn out or broken. Can you give us some ideas before we take it to an expensive repair man to fix

Check the water bottle. Ours has been doing the same but putting a bit of j cloth between what they call the o ring and the cap fixed it. Really you need a new bottle assembly ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

I have a self propelled Royal Dirt Devil vacuum model number 087900 and it goes backward fine but forward has to be pushed so hard it's impossible. Is this a switch? Do you know about how much the part would cost and can it be done by a beginner. We fix a lot of things ourselves but we aren't mechanics by no means. We put a brand new belt on it. I don't think it can be put on backwards and brush turns fine. Where is the switch? Use layman's terms.

You might try a new belt and/or brush roll. The brush roll is what helps pull a vacuum forward, the power drive helps, but if the brush isn't turning like it should, then it will hinder forward motion. The belt may look ok, but they stretch to the ... Vacuums

I have a dirt devil easy steamer deep cleaner that is a few years old but only used once or twice. I am currently trying to use it and when the unit is suctioning I hear a popping sound and then I lose suction. What could be wrong and how do I fix it?

I have always bought dirt devils and this last on that I got is bad it dose not clean by the base boards like the others it dose not pickup stuff from the floor like the others, when you add one of the attachments to it that takes away from the sucki ... Dirt Devil Vacuums

Extension arm The extension arm will not pull all the way up from the holder and I cannot use it - is there a way to take this apart - or something that can be done to fix it?

Hi,\015\012\015\012Try pulling wand up from hose with machine turned off.\015\012\015\012Or are you saying that the wand & handle wont uclip from the body of the machine ?\015\012\015\012 ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

DC25 does not suction when in use? Any ideas as to how to fix it?I removed all hair that was in the rollers and still no suction.

You probably have a blockage in the machine. Call the Dyson helpline to troubleshoot a blockage. They now what they're doing, they'll find a solution for the problem. ... Dyson DC25 All Floors Bagless Upright Vacuum

Bissell Proheat I have a Bissell ProHeat 12 amp 6 cleaning brush upright and it won't turn on anymore. We have done the basics like making sure the outlets work, etc. Changed it around to different outlets. It is not turning on. Any idea?

Things to check are the cord, switch, and the motor. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0599 seconds