Having problems with your Vacuums ?

I have a clarke bench grinder model 1002. I have a light that I would like to attach into the wiring though the grinder wiring in it's base. The light has two wires, and the grinder has a ground that is grounded to the base, a black that goes to a switch then to the motor. The white goes directly to the motor. where would I have to splice in the two wires from the light? I have a switch that I would like to put in for the light on off also.


Answers :

Attach the white wire on your lamp to the white wire on the grinder.
\012Attache the black wire on your lamp to the black wire on the motor side of the switch.
\012This will give the lamp power any time the grinder is turned on.
\012You can put a switch inline of the black wire to the lampp and it will allow you to turn it off when not needed
\012
\012OR
\012
\012 You can attach the white wires together and the black ones before the switch.
\012If you choose this way you will need a switch as the lamp will be power all the time.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a clarke bench grinder model 1002. I have a light that I would like to attach into the wiring though the grinder wiring in it's base. The light has two wires, and the grinder has a ground that is grounded to the base, a black that goes to a switch then to the motor. The white goes directly to the motor. where would I have to splice in the two wires from the light? I have a switch that I would like to put in for the light on off also.


Attach the white wire on your lamp to the white wire on the grinder.\012Attache the black wire on your lamp to the black wire on the motor side of the switch.\012This will give the lamp power any time the grinder is turned on.\012Yo ... Vacuums

Motor wiring My Vax VS19TL motor died and I have managed to get hold of a new Vax 006 Turboforce motor which is the same size . My problem is that the original motor had two wires (black and white) which ran to the PCB switch. The new motor has three wires (black, white and yellow). I have ordered the PCB wiring loom for the 006 motor but I can't find any documentation that tells me where each wire goes. Can anyone help?


... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

Wiring diagram took wires off motor and do not know which goes where.There are two main from plug in one whit one black then two of same coming from light in front.On the motor ther are more terminals than wires.On diagonal corners there are black dots.Can you please help this cost 800$ and do not want to burn the motor due to crossing pos and neg.Do you have a picture or know where I can find?


... Oreck XL21 Bagged Upright Vacuum

Hvr motor -four way switch ,two white ,and blue and brown wires -what goes where


Try this linkhttp://www.youtube.com/watch?v=97ZNEjKtu-gor this link one mite help you ... Henry Numatic "" Canister Vacuum

I replaced a Intermatic light timer with a GE 15086 timer. I have read several solution, but none fit my wire sceme. This is hooked up as a 3-way switch so the second switch can turn outside lights on manually. Here is what I have; Four timer wires: R B W G Wall outlet: B, B & R (Two), G, W bundle What ties in together to make it all work?


1) GE 15086 is not a 3-way timer.GE programmable timers are for single-pole switch replacement only. I have tested this timer, and own several GE timers, and many other brands.2) Open following link to identify timers that work for ... Vacuums

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?


Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum

I purchased a utilitech 7-day digital in-wall timer #0141224. My house wires are two black wires and a green ground wire. The new timer has a w,g, r, and b, wires. My question is what wires do I connect. I found the black power wire from the house. I have no white wire in the switch box. Where would the red wire go? Thank you


Hi!!\015\012\015\012\015\012\015\012The Green wire goes to ground, \015\012The White wire is the neutral. (in this case is used to supply power to the clock.) ... Vacuums

Wiring diagram I have a replacement main switch for my vacuum cleaner. Two blue and two brown but no diagram or markings on terminals to show which wire goes to which terminal


How to Repair a VacuumCleanerhttp://home.howstuffworks.com/how-to-repair-small-appl ... VAX Appliances 2000 Canister Vacuum

My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa


... Electrolux Vacuums

Model # 5770 the brush motor runs and shuts down after a few seconds...Turn unit off and the brush again will run for a second or two...If I don't turn unit off brush will not start up..Could it be the printed board..the motor brushes..or the wiring that goes from the printed board to the main motor...Thank you


Seems like your unit goes into failsafe because it detects something wrong. Well you should check the brushes and replace them if they are worn out. Also check the wiring for shorts etc, becaue the unit maybe tripping due to an overload. The printed ... Bissell Vacuums

I have a philips FC9222 vacuum cleaner. When i switched it on today all the lights came on but the motor did not start. all the lights are on and you cant adjust the power up or dow n using the button on the top. the whole thing just looks like it has frozen on. i would be grateful if anyone can help. thank you.


... Vacuums

On my Kenmore whispertone 5.1 the bearings are bad on the motor there are two bearings they are listed as 608 BRS I see bearings all over ebay 6082RS 608SS but none BRS can I use any 608 Bearing or does it have to be a 608 BRS Bearing are these dry bearings or greased bearings I cant get any real information on the bearings I dont want to go to sears when I can get bearing much cheaper off ebay can some one shed some light on the bearings I would use the motor is made by Lamb Ametek went to ther


... Kenmore Vacuums

We have a series e rainbow cleaner. my wife had been using it i turned off and turned the canister up sie down to get the serial number. it would not turn back on.we need a new hose and thats why i was looking for the serial num. it has a rocker switch and the motor will work on low but will not run on the suction side. i have checked the wiring harnesses out as best i could without taken it all apart. im wondering if it may be the switch. it started once and then stopped.


There is one way to verify if it is the switch.It's kind of dangerous though,but not too bad.You need an extra piece of wire,fairly thick.I would use 4 guage myself.Hold it with pliers,just in case it gets hot.Turn the switch on and hold the wire to ... Rainbow Vacuums

No motor when switched on two red lights flash,cleaned hoover, put back together motor started,then cut out after a few seconds


I would double check your wiring, Make sure all wiring is tight. No cracks, no pinched wires. If needed, bypass the switch and see if it will stay running. If so, switch would be bad. If it's the same, then you have a wiring problem or a worn motor a ... Sebo Automatic X1 Bagged Upright Vacuum

I have a motor for the Bissell 3750 power head with a black and brown wire, which wire is connected to what?? The old motor just had 2 black wires. There is a blue wire coming from the vacuum and blue wire coming from the light that are together, and a blue wire coming from the light and a black wire that are together. What does the blue and brown wire coming from the motor connect too? Thanks


... Bissell 3750 Lift Off Bagless Upright Vacuum

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums

Local vacuum repair shop replaced motor in Oreck XL 2600HH and now the lights blow out immediately upon powering up the machine. I believe the wires for the lights were mis-wired to the terminal blades on the motor housing. is there a wiring diagram available to properly connect the wires to the motor housing?


Hello. if this repair just occurred return this vacuum to that repair shop as they owe you a valid repair. I agree that they caused the lights blowing out problem. They must repair this for no charge. If you work on it yourself they will blame yo ... Oreck XL2600 Vacuum

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i


At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

My Dyson Root 6 made a loud banging sound, and now its motor emits a strong burning smell every time it's switched on. It runs for a second or two, making a lot of noise, and then stops. (Just bought a new battery for it, too - what a drag...) It's off warranty, and Dyson wants almost as much to fix it as a new one would cost. Is my Root 6 e-waste, or is there anything that can be done for it?


... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula


There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby's are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,


You can get better prices from Goodvac.com ... Kirby Generation 3 Bagged Upright Vacuum

I was changing a light bulb with one of those metal extension rods that unscrew and screw back in the replacement bulbs. It evidently didn't seat correctly and pulled off the bulb and created a quick "poof" type electrical short. I have switched out that bad bulb with a new one and can't get either the fan or lights to work. There doesn't appear to be a reset switch. I also swirched out the wall switch to see if that would make a difference and it does not. Any thoughts or ideas would be appreci


If you have not already done so, I would check at the fuse or circuit breaker panel to see if you have blown a fuse or tripped a breaker. ... Vacuums

Can the two inlet pipes be connected to one line? The central vacuum I have is probably from 1993/4. It has one exhaust pipe and two inlet pipes. It was initially under my stairs. I would like to move it and have in fact moved it to the garage but am now fitting the pipes. I would like to join the two pipes that were previously going to the two inlets into one pipe. Can I do it? Also would I then join the wires? Would I put a plate on the other inlet? THANKS. It is a SMART president's choice vac


There is no real reason why not...As long as you have enough "****" then that should be fine, you will need to "Y" join and NOT a "****" joint. ... Vacuums

We have a dyson dc 07 animal the machine was working fine then switched off after returning to the machine minutes later it wouldnt switch on, i removed on off switch cover and used a short piece of wire across the brown wires flicked the wall switch and it worked, aha i thought faulty switch aquired a new one to no avail and now even the short piece of wire trick doesnt work, has the motor died do you think, it wasnt over heating or making strange noises prior to refusing to work


It could be the motor. I'm having to replace the brushes on my DC 05. It appears that you can only get brushes for the YDK motors in the DYSON, not the Panasonic motor. Which might be saying something about the YDK motors. What happens is that the ca ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Confusion and embarrasement have caused me to appeal for expert advice. I need to add a second flourescent light fitting in the loft. I recently added one from the existing wiring circuit via junction box and pull chord switch and it works fine. I have wired in the second light and now neither of them work. I have replaced the starter (as I had a faulty one in the first light. But i annot get them to work. I have installed a second junction box for the second light and wired all like terminals


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0981 seconds