Having problems with your Vacuums ?
Leg messager 'Leg Beautician' SL-c11 stopped working. Any instructions how to fix or open it
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Leg messager 'Leg Beautician' SL-c11 stopped working. Any instructions how to fix or open it
My filter queen majestic quit working. I opened up the unit to see what was wrong and I did not immediately notice anything wrong. Upon furter examination I noticed one of the traces on the printed circuit card was burnt. I used a soldering iron to "bridge the trace and it appeared to fix the problem for a while. Now it has stopped working again, and when I jumper the trace to run the motor it seems to work. Should I just replace the card? Or is there a more serious problem with too much current
I recommend replacing the card. Soldering involves the risk of further damaging the card, so it would be useless anyway. Why waste valuable time?\015\012There is a possibility of the motor overheating, generally due to a blockage in the airfl ... Filter Queen Majestic Canister Vacuum
I have a Wertheim 4808 Barrel vacuum cleaner that has suddenly stopped working. I believe that there is a problem with the electrical cord connection inside. I have tried unsuccessfully to open the compartment that leads to that area. One side unscrewed with a phillips head screwdriver but the other side seems to have a different type of fixing screw that I am unable to undo. It is awkward to get at and in a deep slot and the head of the fixing screw? is not visible.
The steam mop was only used 3 times.stopped working. It has now stopped working altogether. I have only had it for a month. I did not save the receipt because after the third time working I thought it was okay. I am very disappointed and have a hand shop vac of Sharks which has been working for a year. I have been discouraged from buying another one of your products now that the steam mop has quit working after 3 times. I followed the exact instructions how to use it. Model S3101/ 120V 60HZ
Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
I cant detect where the damage but it dosn't work or even the light indicator didn't open, no heat even in maximum level, i plug in for almost an hour but the iron is not responding or not really working and still cold.... how can we fix to make this appliances work again? tanx,
If it's an old iron, then maybe there is some loose wire inside, which could be fixed with proper tools and some knowledge of electricity, but if you are not familiar with taking apart electric appliances - you should just replace it, because it is p ... Vacuums
We have a Eurolab XR210 Robotic Vacuum, it has stopped working. The fan will run, but the wheels do not drive, the UV light does not work, however, it will work in Docking mode. Can it be fixed?
I have a craftsman garage door opener remote control model TX2028 139.18191. The remote stopped opening or closing the garage door. I replaced the battery and tried to re-program it through the LEARN button as per the manual of the Garage 1/2 HP opener. The process has failed after several trials and the remote is still not working. Is there anything else that I can try or should I get a new remote. Thank you
The KP1010 was at rest all winter long. It has worked beautifully before this. It is now working but we can't stop it from brewing. It works but it delivers the water at the rapid cycle. We have water all over the place. Is there a way to fix this?
Sounds like the flow meter is stuck open, letting water keep running. Go to www.krupsusa.com. Then to parts, then pick your model number, this will give you all parts for you machine. Also click on schematics and it will give you a breakdown for your ... Vacuums
Bissell 6900 stopped working how do I open the thing?
Bissell 6900 Digipro ON OFF Power Switch failed. I found the wire connectors for the power switch were corroded. I fixed this by soldering the wires directly to the terminals leading to the motor. To access the circuit board and the on.off power s ... Bissell 6900 DigiPro Bagged Canister Vacuum
My Hoover spin/scrub floor cleaner has stopped scrubbing- the brushes spin for a few seconds right after turning it on, then stop until I turn it off and then on again. How can I fix this? I do not have a lot of money. I have taken off and cleaned the brushes and bottom vacuum opening.
Hi giacoma11,The common cause for this problem is the belt of your vacuum. It could be that the belt came loose or already worn out and needs replacement. To check if the belt is loose all you need to do is unscrew the bottom of the vacuu ... Hoover H3060 FloorMate SpinScrub 800 Upright Wet/Dry Vacuum
Need technical help for my miele s2180 momentum canister vacuum .Bought a display open box at fure shop..Came with a filter bag..there are no tears in the bag...Perhaps they put the wrong bag..Anyway after 30 minutes of use..The motor stopped working ..so I opened up the unit only to see,.the dirt was everywhere inside the vacuum...only a little was in the bag itself..can you hepl..Dave
Hi, I have a Miele s247i vacuume cleaner- My electric coard does not roll back, How do I open the vacuume lid / housing to fix or replace the spring? do you have instruction manual on how to open the cover?
I was in the midst of vacuuming with my Dyson Animal when it stopped working. It smelled as though part of the motor burned up (there was hair and string wrapped around the brush so I stopped to remove it). Any ideas on an easy, quick, and inexpensive fix? Thank you!
Hi there,For guidance on clearing any remaining threads or hair from around the brushbar and resetting the machine, please follow the steps shown in the video below. Please note, the brushbar will never rotate when your machine is upright, so ... Vacuums
Hello, my Kenmore 27514 canister vacuum only works on the hard floor...the carpet suction stopped working while I was using it. Is there anything I can do to fix it or is it necessary to take it in for repair? The vacuum is only 1.5 years old. Thanks. Susan 702.340.8015
You need to replace the belt that drives the beater bar. You can do this yourself very easily. If you need help, let me knowJim ... Kenmore 27514 Bagged Canister Vacuum
I just purchased a westclox tech model 70014 yesterday. I read the instructions and set the time. About an hour later, the time reverted back two hours. I read the instructions again and repeated setting the correct time. I assumed it was working. However, I woke up by myself today at 5:30am, but the clock read 1:14. Is there any way I can fix this or is it a manufacturing defect?
I just purchased this product and used the Turbobrush on 1 chair and it stopped working already. I have gone through my instructions very closely and I cannot figure out why it now will not work. Help!
It seems to be time to take the machine back to where it was purchased for warranty repair or replacement. Good luck! ... Bissell 1425 Little Green ProHeat Handheld Steam Vacuum
The suction on my eureka optima stopped working but the roller still works, what might i do to fix it?
Hi there. Most suction problems are due to a blockage. Start with the base and look carefully for debris that is stopping air flow. You may have to remove the base plate to get to the problem. I am including a link to the manual for your machine. ... Eureka 431A Optima Bagless Upright Vacuum
My vacuum just stopped working, so I don't know what the problem is. I used it in the kitchen to vacuum the hard wood floor. I turned it off, and a few minutes later, turned it back on to finish vaccuuming the kitchen floor. It just would not turn on. I had not unplugged it or did anything to it. I then tried to see if it would work in another plug, and no luck. I'm trying to figure out if it can be fixed or if I need to look for a new vacuum.
When I get most Vacuums that have dies on people most of them the wire has been worn and cut one or more wires on the plug cord. Sometimes the cut can be over looked. Please unplug and check the wire carefully.Also please post the make model a ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum
No Suction My two year old Kenmore Progressive stopped working in January. The guy at the Sears service center convinced me that buying a new one would be cheaper than getting it fixed. So I bought the exact same model and now this one has given out in the exact same way! I'm so confused. When I press on, it lights up and makes the whirring noise. Everything seems to be working but there is no suction anywhere. Not in the main part or the hose and there's no "cyclone effect" in the chamber. All
Try looking within the vacuum to see where the suction is getting stuck at. You may have to do some disasselbmeing but this is a manufacturers problem. You should also try to speak to the manager at the support and make a big dispute until you get yo ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum
Hi we have a model 31075 which i did not find in the list im hoping it's similar to the 31079 The problem is that the agitator has stopped working and i can not open it to find the problem is there a manual available or a site i can go to. Can you suggest what i can do to open it to look around I am very handy with most things but this thing has got me frustrated at this point. thanks for your help. Regards Chuck
... Kenmore 31079 Upright Vacuum
My wife has a Revlon Rv051 curling iron .. has worked fine for several years but now it has stopped working. No response to pushing the ON switch (normally turns on a red LED). I've opened the unit and verified the integrity of the cord and swivel contact between the cord and the PC card. Unfortunately w/o any documentation of the PC card, I'm at a loss as to what to try next. My wife has had this unit for several years ... liked it well enough that she now has two more of the same model but
Is power making it to the switch? Sometimes the plug of the unit with pushbuttons has issues and fails. Maybe you can switch a plug from 1 of the other ones you have to test. ... Vacuums
I have a Shop Vac (Wet/Dry) Model 5275 (120V 60Hz 6.4A), Peak HP of 2.75 While vacuuming the Shop Vac fell over, stopped working, and would not come back on again. Tried plugging into another outlet, etc., but nothing works. Is there some internal problem that I can fix myself?
... Shop Vac Vacuums
I have a light ballast that stopped working. The lights around this one bulb still work but changing the light bulb did not fix the problem. Any idea what is going on here?
The ballast is like a fuse and the ballast is blown .\015\012you will need to replace the ballast as it will let current thru for some bulbs but not enough to light them all up.\015\012also if you use old bulbs that are alomst blown and n ... Vacuums
My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa
... Electrolux Vacuums
Dyson 28-animal- Power brush stopped working and power light and carpet level buttons all are blinking. Per the instructions vacuum needs reset by turning it off for 30 seconds. However after doing so it does not reset and work. Help!
... Dyson DC28 Animal Bagless Upright Vacuum