Having problems with your Vacuums ?

I just purchased a Hawaiian Breeze stand fan FS40-U3 from Walmart. The box seemed to be sealed, but there was no instructions for assembling it. We know what to do with all the parts except a large spring coil. Can't figure where it should go!


Answers :

The coil goes at the base of the pole stand.. You slide it up through the bottom before you attach it to the the pedestal.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I just purchased a Hawaiian Breeze stand fan FS40-U3 from Walmart. The box seemed to be sealed, but there was no instructions for assembling it. We know what to do with all the parts except a large spring coil. Can't figure where it should go!


The coil goes at the base of the pole stand.. You slide it up through the bottom before you attach it to the the pedestal. ... Vacuums

My mother purchased a replacement hose assembly for a Bissell ProHeat 2X and the part was shipped without any instructions... While I am pretty handy, my issue is with the supply tube, and I cant figure out how to accomplish the replacement, and as its not MY vacuum, Im hesitant to start taking things apart.I just need instructions to replace the entire hose assembly.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Kirby Generation 3. The handle spring assembly is broke, so I took it apart to get a part number. Can you tell me if there is a cross reference or something on these parts. I am unable to find a part with the same number that is located on the part I took off. The number on this spring assembly shows Kirby HA-670289B K-1. Any help finding this part is appreciated.


... Kirby Vacuums

Have Dyson DC 14. When tilt to vacuum, the handle and coiled hose comes away from the unit. The problem started when the little purple ridged curved part on front of vacuum cleaner right below handle came loose and a spring fell out from somewhere--don't know where. I pushed on the purple ridge part and it snapped back on. Now, can't get it loose again, don't know where the spring goes, and handle still comes loose from vacuum.


I'm not positive whether or not this is the wand handle because there are several versions of the DC14. However the device the locks and unlocks the wand in place is pretty similar between all the versions.The first picture is the wand re ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Hoover Steam Vac Dual Tank Bottom Valve Spring Assembly Part Needed


It appears that there is a problem with the o-ring design. The o-ring should maintain a certain OD dimension and keep the spring assembly from pulling throught the hole. I am trying to find the service manual to locate the o-ring part number but hav ... Hoover F7431-900 SteamVac Vacuum

I have a Hoover 6630-900 bagless upright. The "valve arm rear, part #38719048" broke. I have a repalcement part, but cannot get the spring, frontt and rear arms assembled correctly. Ant hints? Do you have a photo of the assembly on the vac? Thanks, Lee Duncan


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I need a Dyson DC 17 Total Clean exploded parts diagream that shows the switch assembly. There are two small springs and a small plastic part that were loose inside the switch assembly. This caused the vacuum to shut off in the full upright position which is the position you use when using the wand.


I don't have a full diagram for you, but I do have a photo of how they are meant to be assembled: ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

On/Off switch button, brushbar switch button, brushbar reset arm, and springs assembly. Does anyone know how to put this back together?


Go to this link for help and pictureshttp://manchestervacs.co.uk/DysonForum/index.php?topic=564.0 ... Dyson DC25 All Floors Bagless Upright Vacuum

Hoover model u5753960 shows a photo on Sears Parts Direct of part number 42259027 (housing) with a separate spring and a separate screw. Does anyone know where those two parts are supposed to go ?


Hello there, as per the picture you posted in your last comment here is a schematic for the assembly of your unit. The part should be the main casing of the unit and ... Hoover U5753 Bagless Vacuum

Parts diagram I have taken the assembly apart and I would like to see a diagram in order to know the part numbers that i need to order for repair.


You may like to try here see if yours is listed http://onlinevacuumparts.com/s-3-bissell-vacuum-parts.aspxriz. ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

I am replacing the front wheel assembly and TORSION SPRING on a windtunnel bagless model U5750 and I can't figure out where the torsion Spring is supposed to go?


... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

Assemble i don't know how to assemble it i don;t understand were to put the part that goes in the canister to retrieve cleaner. to get it through the nossel


This website should help.\015\012http://www.bissell.com/images/UserGuides/16311.pdf ... Bissell 1631 PowerSteamer ProHeat Canister Vacuum

Replacing front wheel assembly part # 2031330 / model # 6594. can't figure out how to get the part under the lip once you slide end pieces in their slots, thanks ,steve


... Bissell 6594 PowerForce Bagless Upright Vacuum

How to wind cord onto spring loaded retractable cord reel for a Kenmore canister vacuum. There is a metal 'U' shaped, spring loaded, piece that fits over the outer aspect of the wheel. If cord needs to get wound on under this metal band I can't figure it out and the band is like factory sealed onto the wheel. Also. I don't know which direction to feed the cord onto the wheel


What is the exact model # please?Thanks!! ... Kenmore Vacuums

I need to know how to remove the dirt container on the eureka bagless vacuum. It says that it is easy to remove, yet we cant figure it out. is there some trick to it that we dont know?


There is a lever at the bottom of the dirt cup,turn it to the left and pull out the dirt cup.note while you have the dirt cup out make sure you clean all the filters there is one right above the dirt cup pull out on the right side and there is a filt ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Sweeper belt Hey , i own a fantom thunder sweeper and recently my belt keeps slipping off, i've disassembled it and put it back on a hundred times but it keeps doing it after a few minutes of cleaning , Am i missing a part to hold it on or somthing else wrong i've cleaned it and checked all the ports just cant figure it out and cant find any info online thanks for your time tina


Greetings from GoVacuum.com,Have you replaced the belt with a new one yet? You may want to try replacing the belt, as with flat belts like the Fantom Thunder, they do stretch out 4 -5 inches after time. We in fact recommended replacing ... Fantom Vacums XT450K Upright Vacuum

I have a Kirby Heritage 84. Great condition except the part that connects the innerbag is missing. I don't even know what it is called. I can open the vacuum cleaner bottom and see that the part is missing. It should be oval where it connects to the vacuum and then extend into the cloth bag. PLEASE HELP!


The Heritage 84 had two different bag assemblies available. One is a dump-out bag. The dirt simply dumps through the bottom. The other is the bagged style which has a full length zipper to open it. Inside it should contain a "bag fill tube", and a to ... Kirby Heritage II Vacuum

I have a hoover u6630-960 wind tunnel. How do you connect the torsion spring valve arm part # 38358001 with the valve arm rear - ag part # 3871948 Thank you


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I was changing the pump belt now i have this lever like thing w a spring on it that i cant figure out where it goes or how it came off


Could it be the handle lock lever ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I need to change the motor in a vax 6131 but i don't know how to get into it to get the change it? I also need to get into the motor assembly housing to change a part but can't see how it comes apart!!


On the handle there is one small pozidrive screw, remove and orange panel comes away revealing powercable securing bar. Remove 2 screws and this reveals a 10mm headed bolt. Under label on top of handle there is another small pozzi screw, undo t ... Vacuums

The spring assembly popped out of the electric head telescoping wand? Is this repairable or is wand available as separate part for purchase?


Replace wand ... Beam Industries 2775 Serenity Plus Central System Vacuum

Cant find manual for model f5880-900 hoover steanvac spinscrub dont know how to attach upholstery parts


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I cant put it back together, i emptied the part that holds the dirt and know it won't fit together.


Try incerting the top of the cup first ... Eureka Whirlwind Litespeed 5840 Bagless Upright Cyclonic Vacuum

My DC-25 will not return to the upright position. I emailed Dyson support and the response was: "The DC25 stabilizer wheels will not lock into position if the “spokes” on the red pedal are not seated correctly." I agree with that assessment, but cannot figure out how to get the spokes on the red pedal to seat correctly. The manual is useless for this problem since that part of the vacuum cleaner came already assembled, so the manual does not address it. Help.


It sounds like the undercarriage unit has failed. It is a common problem on ball models. The DC25 is a recent model so would still be under Dyson's 5 year guarantee. Get them out to it. ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Hi all---I have a Dirt Devil 091020V. there was a problem with the wand where it was the only thing sucking even when it was stuck in the tube it would ****--but nothing from the vacuum end--the diverter was stuck closed I took it apart and found something stuck but in the meantime the torsion spring [I think} fell out and I don't know where it goes--so now only the vacuum works --not the overhead cleaner part.. is there a digram somewhere that can tell me where it goes--I think it might b


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0645 seconds