Having problems with your Vacuums ?
My dyson 05 keeps on over heatin after only doin one room and cuttin out
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
My dyson 05 keeps on over heatin after only doin one room and cuttin out
Vax lightweight HEPA had for two months, Hoover one room turn off go to next room and won't turn on again for a few hours ( normal size rooms)
Part replacement we have one of your "Shark steam cleaners", that while moving from one room to another, was dropped. The head separated from the part that holds the water and broke in the process. Can this part be purchased.
Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
Hoover Bagless Windtunnel (tank tyle) selfpropeled head throws belt; 2nd one doing exactly as the first vacumm.very hard to put it back on .can't even get one room done
Is this a new belt? If not, get a new one. Check the brush roll, make sure the ends are turning freely, if not, replace it. If you are catching things like a throw rug and towell or some other thing, this will cause the belt to get knocked off of ... Hoover Vacuums
Every time I try to vacuum my apartment with my Dirt Devil Featherlite bagless vacuum, it shuts off before I have finished one or two rooms. I then have to wait 30 minutes before continuing. I had the vacuum for 2 months before exchanging it and it is doing the same thing with my new one. It seems to happen after the first time I empty the cannister. Any ideas?
Your motor in the vacum is getting hot.Thats why it shuts off.Its fitted with a shut off switch to stop you doing any damage to it.1 The reason for getting to hot is that you are filling the cannister to full.Try emptying it half.good luck. ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum
The thread that goes through one of the two needles on my wife's 304D ZY Lock keeps snapping. She has changed the neeedles & I have given it a good clean but still keeps snapping
One reason could be the thread tension. If it is more the thread will snap. Please loosen the thread tension and run it. It should not break. ... Vacuums
We have the water hooked up at the back of machine. there is a spout for the water to come in and fill the ice tray.but is does not. If we turn the water on it fills up the space under the ice basket. I keep getting red light and then the two smal llight one ice and one water come on. We can hear the motor trying to fill the ice try and then lights come on. Please help me this so I can use this product. It did not come with a manual.
The water inlet valve on the back of unit opens when the ice maker needs water. If the valve doesn't seal good because of sediment or wear it will continue to drip and when the water reaches the ice maker supply tube it will freeze blocking the fill ... Vacuums
We have a 2001 Kirby G vacuum. The cleaning lady was using it in one room, then brought it to another room and plugged it into another receptacle. It wouldn't start. Naturally we tried other outlets on other circuits without success. Is a switch or motor demise this abrupt? Is it worth pursuing repair?
Hi,Such an abrupt fault is more than likely a very simple fault, such as a loose wire or damaged electrical cord or a faulty switch. I would most certainly check or have these components checked before purchasing a new machine. They should be r ... Vacuums
My hoover Wind Tunnel vacuum cleaner's motor spindle keeps overheating. Because of the high temperature, it keeps burning through belts (the big, wide ones). I have taken it in to the vacuum repair shop about three times now, and the problem has never been fixed. Does anyone have any advice on how to fix this or should I just buy a new vacuum?
Belt keeps coming off even though I replaced it with a new one. It will not stay on keeps throwing them off.
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=40485&thid=739734\015\012Belt (by 2 users)\015\012Posted by lynndian on Jul 04, 2008Belt keeps coming off even though I ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
My Dyson DC07 has recently been service and was making a clattering noise and very hard to push. We have taken it back and he has changed the clutch mechanism under the base which has solved the clattering, but it is still really hard to push because of the suction. It is even lifting the carpet in one room. Can you tell me what the possible reasons for this could be? One thought we had was that the little rubber wheels on the bottom cover could have worn so the hoover is closer to the floor
On the sole plate you should have 5 little wheels, these are prone to jamming after a while. You should make sure these are not jammed in anyway.\012\012You can release these with a screwdriver, but be careful not to prize too hard as you ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Kenmore Canister Vac, Progressive, 25512 255513 model. Brush won't turn. One end of the brush roller, end closest to belt, is off center which is keeping it from turning freely. The end cap is like a square. Other ends turns fine. Do these end caps come off? If so how? Can't get it to budge. This is exactly what is keep brush roller from turning.
Take a flat head screw driver and pry the end cap off. It will come off. You might have some string or hair around it causing it to not turn. ... Kenmore 25512/ 25513 Progressive Canister Vacuum
My wind tunnel keeps breaking its belt. The big one. The little one is properly attached. This is a recent problem so it has nothing to do with the rug height settings. I just broke two in the course of 15 minutes. The bag is NOT full, the brush/beater has been cleaned and properly attached Help.
Well will the brushes turn freely as they run in bearings if its got wool of cotton raped around the side of the brushs that will make them tight to turn and will brake every belt you put on it, in a flash,,,\015\012the other thing that causes ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
New Rainbow purchased 3 weeks ago. Went to a friends home which purchased one also and her's is very quite. Mine on Low setting to use as air clearner you can hear it in the next two rooms. Her's you had to atleast be in the same room and still can talk. I believe I have a bad machine.
Your new rainbow is still under warranty I believe so explain it to the company and ask for another. I too had a rainbow however I am like your friend in which mine worked very well. The noise is coming from the motor housing or the motor itself. ... Rainbow Vacuums
Dirt devil vision belt keeps coming off even new ones
No suction I have a bissell turbo heat upright carpet cleaner. I've used it once and loved it. I cleaned one room today and realized it wasn't sucking up the water and is louder than before. Please help.
If this is a 9400 series check and make sure the red flap in the lid of the dirty water tank is not closed. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Hello, My Electrolux Renaissance is about 12 years old. It worked great for years, but now it keeps turning itself off...about every 15 seconds or so. The bag was just changed recently, too. Is there an easy, (and cheap) fix or should I start shopping for a new one?? Thanks!
Odds are you have an obstruction somewhere. Check all of the hoses and the power head to ensure that there is nothing blocking your airflow. \015\012\015\012Also note that if it keeps popping the front bag door open, that's usually indica ... Electrolux Vacuums
I am getting a lot of dog hair on the filter after cleaning one room, this is something new. I cleaned as many parts as I can. It seems like the dog hair is moving from the clear canester onto the top of the filter, any thoughts??
The cone in the tank has a black gasket make sure it hasn't slid to far up ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
I have a hoover floormax supreme and one brush keeps coming off what could it be . Thanks
... Hoover Floormax F4300 Upright Wet/Dry Vacuum
The rollerbar keeps going on and off, depending on if you push it to one side or straight. If you push it straight it does not want to work and cuts off. the vacume is still on but the rollerbar does not spin
It could be that the belt is very worn or stretched to the point that it can't turn the brush against the carpet. If thats the case you can get replacement belts and view the manual here: ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Roomba Discovery Roomba is fully charged and cleaned with sensor wiped clean. When turned on it it sounds normal and commences to go, but it then acts like it is putting on the breaks, spins, tries to go and manages a short distance and breaks again, just not making any progress because it keeps breaking after a foot or so and turns and tries again. Sometimes is gets so stuck from moving forward at all, like it is stuck in one spot just trying to go while seemingly surrounded by barriers. Somet
I had the same back-up, turn, move forward a couple inches, backup-up, etc. problem. Try cleaning/cutting the hair, etc. out from around the brushes, as well as around the ends of the brushes. Also, try a Q-tip to clean out the four pair of sensors ... Roomba Robotic Floor Bagless Vacuum
Rainbow SE I turned the vacuum on and it worked to do one room Then I shut it off to wait until my husband got of his call. I realized that their was cloggage in the vacuum part that vacuums the carpet and unclogged it. I then tried to turn on and it was dead. I have the water filled just above the stick.
The clog may have over heated the motor, usually if you unplug it then after little while, try it again. If it still won't go, does the separator turn easily or is it bound up and won't turn. Take it off and see if the motor will run(without water) ... Rainbow E series Canister Wet/Dry Vacuum
I have a steam cleaner and i can not get the black arm brush to keep one side up and when you trun on the steam cleaner the brush dose not spin when you start to clean the floor but it will spin when you have it siting up right
Sounds like you could have an elevator broken (part #2000010). You will have to take the top off to replace them or to check to see if one of them is broke. There is one on each side so when the handle is in the upright, they push againsy the brush ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
Hover Elite Rewind I've only had this vacuum a few months and I really liked it until now. There is almost no suction from anywhere in the vacuum, and I've cleaned all the filters and rollers with my shop vac and made sure that everything was assembled correctly. It used to be really quiet now it is quite loud and it keeps over heating, and shutting off. At this point I have no idea what could cause this problem, the machine is nearly brand new and I can't afford a new one at this point.
You have to clean out the hose under the bottom of the vacuum cleaner. To do this you have to remove the bottom plate the covers the brush it has about 6 screws. Also remove the brush and belt in order to thourhly clean it. I had the same issue you h ... Vacuums
No suction in hose or base in Kenmore Powerspin. Shampooed whole living room and not one drop of water in dirty water container.
No suction in hose or base in Kenmore Powerspin ... Kenmore 85920 PowerSpin Upright Wet/Dry Vacuum