Having problems with your Vacuums ?

I have sewing machine Model 158 1340281 which has 25 years warranty. The problem is eventhough Motor is running but the belt does not go round .


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have sewing machine Model 158 1340281 which has 25 years warranty. The problem is eventhough Motor is running but the belt does not go round .


... Vacuums

Hello, I have a problem with my Eureka Powerline bagged upright vacuum. It has a 12 amp motor and is model #4352, Type D. It was probably bought new in 1998. My problem is, while vacuuming today the motor seemed to slow down all of the sudden and then began smelling like burning rubber. I shut the vacuum off to check for blockages but could not find anything blocked. When I then turned it on again it runs but seems to only be running at 1/2 the motor speed and still has the rubber buring smell.


It sounds like a rubber sealing in the motor has come loose and is being constantly rubbed against the walls of the motor with would cause the smell and loss of motor speed caused by the fricton of rubber against the rod so if you can get to the moto ... Vacuums

Makita 440 Dust Extractor - Trying to rectify a problem, when i switch on an appliance plugged into the socket, it will not run. IS used to run with this plugged in, but the hoover motor runs no problem. Any ideas what might be amiss, or where i can get a wiring diagram? Thanks in Advance!


... Makita 440 Wet/Dry Vacuum

I have an older Oreck XL vacuum that sounds like it is running twice as fast as it should. I disassembled the entire vacuum, including disconnecting the motor wires, to clean out the hair, string, and other things. When I put everything back and connected all the wires, everything appears to work, including the light. The only problem is, it sounds extremely loud like the motor is running too fast. The model number is: XL3610HH Ser. No. 3610HHXA039740-6 I do not have as electrical diagram to see


... Oreck XL Ultra Bagged Upright Vacuum

Ihave a Hoover Windtunnel self-propel model U6445-920. The belt from the drive motor to the big wheel will not run in the center of the wheel. The belt runs about 1/3 off the wheel. I have tried several new belts and still the same problem. What do I need to do to repair this problem.


The large wheel may be worn off center. If the belt stays on and is not thrown, you can run the vac. if there is wobble in the wheel causing a genuine belt to slide off replace the wheel mechanism. ... Vacuums

Hi I need help because I have a problem with my Electrolux Centralux Central Vac system in my house. When I plug the vac hose in the central vac socket at first I heard the motor running very gently with NO suction then after a minute or so it went completely dead and they is NO motor sound, suction, or anything happening what so ever. Can anyone tell me what this problem is???


Have you checked for a clog in the lines or in the hose? If there is no clog in the system anywhere, then your motor could be dying. ... Electrolux Centralux Vacuum

I have Nutone VX550C. Motor runs intermittently (cycles on and off rapidly--the light on the handle is blinking furiously) when I use the on/off switch on the hose. This happens at all of the wall connectors, so suggests a hose contact problem. Motor runs continuously when I turn it on at the switch on the wall unit.


The unit does have a switchs the PVC outlets, and it sounds like the hose mech to operate the switches is broken, and intermittently making contact. A replacement hose would likely fix the problem. Looked them up on the net, and they're not che ... Broan-NuTone VX550 Bagged Central System Vacuum

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v


Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

My Miele Solution HEPA 5000 vacuum cleanr gives off a burning smell but will continue to run with a varying motor tone. I have not run it for more than a minute like this. I have reviewed responses to similar problems but cannot figure out how to access the motor. Can anyone advise?


... Miele S318 Bagged Canister Vacuum

Motor problem machine is smoking/burning smell coming from the bottom of the machine. Motor still turns but doesn't make much sound; and soulution won't squirt. The model # is 1970


I had to throw the machine away before it burned my house down. There is no way to fix it; had to replace it. ... Bissell 1770 Quicksteamer II Upright Vacuum

My bissell model 18Z6 has developed a loud noise and vibration when the brush is running. I have removed the brush assy and cleaned all the hair, etc but still the noise. I ran the brush motor with the belt disconnected and all seemed ok, but of course there was no load on the motor. I suspect a problem with the brush assy bearings or axle or both but I hate to just throw parts at the problem. any suggestions would be greatly appreciated.


... Bissell Vacuums

Brand new LG LUV200r used 10 minutes now after removing dust tank & reinstalling the vacuum motor does not run only the beater bar??? I have located wo circuit breakers both seam to be set. This suction motor should run when the switch is pressed & the beater bar should operate when the handle is moved down??? Not A happy customer will return unit to Best Buy only 100 mile round trip!!!! RDH


... LG Electronics Kompressor Pet Care Upright Vacuum Cleaner LUV200R

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o


Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Recently my central vac system started making a louder than usual and laboured sound when in uise, enough so that I took note and inspected the canister and motor while running. The motor was trowing off blue sparks and looked like it could 'POP' at any moment. I will not risk using it until I know what the problem is and how to repair it. My assumption is the motor needs to be replaced. The system came with the resale house I bought 3 yrs ago but I do not know the age of the system itself.


... Vacuums

Miele Cat & Dog vacuum gets VERY hot and is VERY loud. Hose has no restrictions and I have changed the dust compartment (motor) filter and the exhaust filter. It still gets hot when I run it with the top open and all filters removed, so I'm guessing the problem is with the motor. Should I be going into the motor compartment? If so, what am I looking for?


Hi\015\012\015\012The fact that it gets very hot could be due to a number of issues.,but the fact that it started making a very loud noise at the same time suggests that there might be more problems maybe brushes etc.\015\012\ ... Miele S514 Solaris Bagged Canister Vacuum

I have an Electrolux LITE upright carpet cleaner - about 15 years old. Suddenly last night when using it, from the normal motor (whooshing) sound, the motor suddenly went very slow and with a slight grinding sound. The brushes are now just turning round very slowly and areobviously not picking up anything. Has the motor gone or is this repairable, or should I just get a new cleaner? I have tried to open the machine from the bottom to see if anything is obviously wrong, but it looks complicated a


... Electrolux Vacuums

Lately, my Kirby Ultimate G has been acting funny. When I push it forward, it's fine, but when I pull it backward on the carpet, the light on the front flickers and the power flutters off an on. I thought it might be the rollers, so tonight I turned the machine over and pulled out the hair that was wrapped around the roller. However, that did not fix the problem. I should probably backtrack a little bit. In the past, I have had problems with the vacuum running over its own power cord.


The cord will need to be replaced with a cord made for the machine, as it has a non-standard plug. The cord cover is held in place with a # 20 Torx screw. Remove the screw and push the cover gently from behind to unlatch it. The handle must also be r ... Kirby Ultimate G Bagged Upright Vacuum

The number 2 light is blinking and I can't get the machine to run. I know that when number 1 light blinks its because of the lid. What is the problem for the number 2 light on the island oasis machine?


... Vacuums

My filter queen majestic quit working. I opened up the unit to see what was wrong and I did not immediately notice anything wrong. Upon furter examination I noticed one of the traces on the printed circuit card was burnt. I used a soldering iron to "bridge the trace and it appeared to fix the problem for a while. Now it has stopped working again, and when I jumper the trace to run the motor it seems to work. Should I just replace the card? Or is there a more serious problem with too much current


I recommend replacing the card. Soldering involves the risk of further damaging the card, so it would be useless anyway. Why waste valuable time?\015\012There is a possibility of the motor overheating, generally due to a blockage in the airfl ... Filter Queen Majestic Canister Vacuum

Switch Problem The red switch to put on wont stay on the motor runs but as soon as you release your finger from it the motor cuts out. what do I need to do to make it work as it should?


It sound like the switch is loose if you are able take the handle apart and plug the leads back into the switch. be sure to unplugit ffirst ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Currently my dyson does not work when in the upright position. When I pull the handle back, it will run, but the suction is not very good at all. I tried washing the filter, but that didn't work. Sometimes it works for awhile, but then the problem occurs after the machine has been used for awhile. What do you think the problem is?


Hi its Darran at Dyson.It sounds as though the brush bar may not be turning properly when you put the machine into the upright position. To test, lie the machine on its side in the vacuuming position (head released) then switch it on and ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a new bag in, checked the hoses for clogs have the motor cover off showing motor runs. Problem is vacuum has no suction in hose area, cover off where bag is and the air blows out of filter. hoses are clean no blockage.


Have you checked the filter? Many vacuums have a filter under or behind the bag to keep dust and dirt out of the motor. If this gets clogged the motor can't get any suction. Also look for holes in the hose or in the small segment between hose and bag ... Vacuums

Hello, I have an Electrolux vacuum. In desperation, I vacuumed up some water and my machine stopped. I am hesitant to take the machine to a repair place for fear that if it is a simple repair they will not be honest. Can anyone give me advice on whether this is a problem that requires a new motor or major repair? Thank you!


Although it's never to be recommended, it is sometimes possible to vacuum up a little water without doing significant damage. However, the fact that your machine then stopped suggests that the electrics got wet. That may or may not have caused expens ... Vacuums

I have the same problem the machine makes a low humming sound instead of starting up and the response was the motor probably siezed. Where can I get a replacement motor???


Honestly I found one on craigslist.. Now I'm not sure if you will have any in your area but I lucked out and found one. Hope this helps ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

I have a singer 328 and the foot pedal has developed a problem the machine is running all on its own can I fix the problem with the foot pedal


... SewShop.com 328 Singer Instruction Manual .pdf format
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0742 seconds