Having problems with your Vacuums ?

I have used Braun Electric shavers for the last 40 years but now I am having difficulty of finding spares from the Malta agent. I have been waiting for Part number A003143 of the Braun Tri Control shaver 4015 model for the last three months. So will you let me know from where I can purchase the above.


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have used Braun Electric shavers for the last 40 years but now I am having difficulty of finding spares from the Malta agent. I have been waiting for Part number A003143 of the Braun Tri Control shaver 4015 model for the last three months. So will you let me know from where I can purchase the above.


... Vacuums

Bissell 6595 problems with roller brush. I've had this happen with two of the same model. Each one didn't last more than seven months! First, it became loud when vacuuming, then there was a burning smell. When you try to replace the belt, you see that won't do any good because the fitted end of the brush is melted. The housing part the roller brush fits into is melted too. There's no place for the roller brush to fit into. I tried to upload pics, because I don't see how replacing the roller brus


... Bissell 6595 Lift Off Bagless Upright Vacuum

Hello, I have the same model. And though it is three years old, starting from the last month, it does not clean anything anymore. Cannot even pick up one single thing from the floor. Every dirt gets stuck in the hose. I cleaned the hose and cleaned the filters but it still does not pick anything up. Is three years its normal lifetime or do I have the change the filters, instead of cleaning them? Thanks.


I know bissell vacuums are very cheap but they should last more than 3 years. there should be two parts to the dirt cup. remove the dirt cup and above it there should be a round plastic part. unscrew it and check that filter. ... Bissell 6594 PowerForce Bagless Upright Vacuum

We purchased a Shark Power Pet vacuum last month. We can't find the book and now the bar doesn't turn in the power head. We tried to order a manual but the model number keeps turning up as non existant


The model number is EP722 and the technical support number is 1-800-798-7398 Mon-Fri. 8:30 am to 5:00 pm EST ... Euro-Pro S3325 Handheld Steam Vacuum

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin


... Vacuums

I have a Hampton Bay Midili fan which I just installed about a month ago and it was working fine. A few days ago when I flipped the switch on the light flickered on and off consistently until I turned the switch off. The remote also stopped working to control the fan and light. Since this model only can be controlled by the remote I am worried I will have to replace the remote already after only 1 month!


In many of these remote controlled lamps you cant use the new spiral light bulbs .. you can only use standard incandescent lights .. if thats not the trouble then you may indeed have a bad controller (in the fan) .. there is probably at least a 90 d ... Vacuums

I recently purchased a Hoover SteamVac to replace an old one because the brushes would not turn. I used it last week and then tried to use it last night and the same thing happened w/ the brand new model - the brushes won't. I've cleaned the brushed, the filter and everything else I can see. Can you help?


Those things are a waste of money you better off renting one. but the only thing i could think of is that something is stuck or your belt came off track ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Hi, we have a Sunbeam electric blanket model no. BLO750 and type 696. It's a double blanket with dual control that can be used for different settings on either side. Both sides have been working ok but last night one side wouldn't heat and the green light kept flashing and now, whatever we do the green light keeps flashing except, when we set the control to "off". We can't find our Owners Manual to see what we are doing wrong, can you help please...or can you advise us where we may be ab


... Sunbeam Vacuums

I have a craftsman garage door opener remote control model TX2028 139.18191. The remote stopped opening or closing the garage door. I replaced the battery and tried to re-program it through the LEARN button as per the manual of the Garage 1/2 HP opener. The process has failed after several trials and the remote is still not working. Is there anything else that I can try or should I get a new remote. Thank you


... Vacuums

Hi. I have a Kirby from back in the early 90s (model G3D). Never had major issues with it. Can't remember the last time I had maintenance/tune up done. It's just sounding different when I run it the last few times...almost like it's louder and kind of echo-ey. Still suctioning well, but something's not right and I don't want to run it until I know if anything's up. Any suggestions? I'd like to try and figure this one out on my own with your help. Thanks in advance for your help. Marci


Check the belt. this is a strong vaccume and even without the belt it will still have a decent amount of suction. If the belt is not tight or intact it can let the motor turn faster which will sound louder. other than that check all the hoses for hol ... Kirby Ultimate G Bagged Upright Vacuum

My shark vx3 vacumn has stopped running... i tried recharging it, but still no luck... i then put a new battery pack on it and tried recharging, still it won't run... the charge light, (green) is on, the three red lights come on and flash when i push the on button...what should i do next?? this unit is about 6 months old... help!!


... Euro-Pro Shark Cordless Stick Vacuum SV775R Vacuum

Had my dyson root cyclone for about 4 years now, and in the last year it's had a few problems. About 4 months ago it started to make this awful grinding sound when the roller bar was engaged and I took it to a repair shop and they said it was the roller bar itself. The shop replaced the part and it worked fine for a couple of months and then it started to make the grinding noise again. I tried the clutch reset suggestion (turn it on its side and turn the carpet/bare floor switch slowly back and


Bdepends how much thay charged you for a roller brush because you can buy a good vac for about 100 pounds with a 12 month guarentee so its up to you ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dyson DC 14 hose has no suction, with or without brush attachments. Hot air shoots out from the base of the canister when I try to use the hose. I cleaned the top filter, but can't figure out how to remove the hepa filter to clean it without destroying the case. It looks like it might take three hands to insert pennies and "flip" the case open as is suggested on a youtube video for a different model. Would this even help, assuming I could get the thing open?


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

When squeezing trigger and Depressing Clean surge Button on Upper handle of the Hooover Steam Cleaner F5914-900 there is no "snap" indicating trigger rod is in place. Everything else went in as instructed. The screws and bolts were no problem this concerns me because the main complaint I read about this model was leaking from the trigger and clean surge and the problem was not getting the rod in place. No matter how many tries or people (three) it still doesn't occur.


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=552215\015\012Generic problem for all Vacuums\015\012When squeezing trigger and Depressing\015\012P ... Vacuums

The thread off the needle gets caught in the hook race and the machine eventually stops. Tried different tension on the needle and the pressure adjusting lever is set at three. This is the second time I have used this new Kenmore Model 385.16231.


... Vacuums

Passat 2000 W Reg Had the rear brakes and disks changed then a month later had a front tyre replaced and as I drove off something went tinkle tinkle on the road (like someone had left a spanner). Week later the ABS light and the brake light come on with the usual STOP Brake Fail Service Manual message. Had brakes checked but they could find no fault. I've tried the ABS under controlled conditions and it works. What could the problem be?? I've been running the car under these conditions and no pr


The ABS module has a history of wearing out on VWs. Nothing wrong with the brakes themselves, but the ABS module would need to be replaced to stop the lights coming on... but the problem is a new ABS module can be very expensive for a new one (~$900 ... Vacuums

Vacuum either stops for no reason and can't be restarted without unplugging and waiting 1/2 hour to restart, or it simply will not turn on at all. The red light comes on when the "On" button is pressed. I took it back today for the 4th time in a month to where it was purchased. They called later and said it was running fine and they could not detect a problem. The last three times they have (1) replaced the roller brush, (2) "unclogged" the vacuum, and (3) "adjusted" the belt.


This sounds like it might be an overheating problem. \015\012\015\012Some vacuum motors are fitted with thermal cut out fuses or thermistors which cut off the flow of electricity to the motor when the temperature gets to high. It is possi ... Lindhaus Activa 30-38 Bagged Upright Vacuum

I have a Bissell pet hair eraser model #3920. It's been working great until last night. I went to use it and the brush won't spin. It also smells like it's burning. I checked the belt and it looks fine, and the brush spins by hand easily. It's not clogged anywhere that I can see. Anyone have any other ideas? This vacuum is only 8 months old.


- Remove the access panel, which is on the bottom of the machine. There are 4 tabs to lift on the access panel to remove. Start with tab 1 then 2-4 tabs.- Check the brush, and belt for any damage. Clean off any debris on the brush. ... Bissell 3920 Bagless Upright Vacuum

I was in the middle of using my vacuum when it quite on me. I tried multiple things including letting it cool off for a while as I was using it to vacuum my car outside and it was pretty hot. I also dismantled it according to the directions and looked for blockages and didn't find any and lastly I cleaned out the brush and put it back on. I am out of solutions. The vacuum is not that old; we have only had it for a few months. Any assistance would be appreciated. Thank You, Karen


Hi the problem you are more than likely having is with the wires that go into the vacume they are not that secure and do work loose.now if you remove the cylinder that you empty, now you see where the wire goes into the back of the vac, w ... Dyson Ball DC24 Bagless Upright Vacuum

After three months of use it stopped releasing water from the bladder. I have a bissel proheat 2x model #8920


Sound like the pump fail, it will also cause solenoid to fail and need replacing 19.00 bucks pump and solenoid 11.00 bucks, easy and cheap to replace yourself. go to provac.com for parts. even if you get both part but one still working i ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My FIL purchased an Electrolux bagless canister vacuum model EL5 76501 last year. When I tried to use it today, the hose keeps pulling out of the power brush whenever I pull it towards me. it doesn't seem like anything has broken off. The only thing I noticed was that the rubber ring washer seems to be flattened. Could it be something that simple or do you think some part has fallen off and gone missing? Regards, Craig Somersett


I believe I've just had the same problem and after searching for a small gray horsehoe clip that needs to first be found and then inserted into the slot for it on the tube section that comes out of the beater bar. Insert this clip from the outside af ... Electrolux Vacuums

Dear Sirs, I purchased two Braun 5875 Contour Electric Shavers in May 2009. I didn't start using one of these new shavers until August 2010. In January of this year I found that the contour part of my razor started to flex on one side and the spring clip that retained the foil became loose. I didn't get very good shaves from this Braun razor and put it down to the pattern change of the foil itself. I have always used Braun shavers because I was of the opinion that German made articles were alway


... Vacuums

Vaccuum issue I just bought a Eureka upright model 5892 BVZ, my concern is, I bought it on sale (floor model) and it didn't have a manual with it. I took it home and tried it, and although it appears to be working very well there is not dirt in the catch bin on the front of the unit. I tried the hose w/attachment and again it worked very well in picking up the cat hair, but where does the hair and the dirt go, I am afraid it is spitting it back out somewhere since I can not see anything in the c


If the dirt being vacuumed is not going into the dirt cup, then it must be just stuck in the hose and evenually will clog up. Check the hose and see it there is a clog in it, otherwise you have a years warranty on a new vacuum, take it into a warran ... Eureka 5892AVZ Bagless Upright Cyclonic Vacuum

My danby kegerator model DKC645BLS controller circuit board corroded and no power to the compressor,I already have an external temperature controller,can I just bypass the controller and circuit board


... Vacuums

I bought a house that has a 1970s GE microwave oven that's built-in above a traditional oven. (Unfortunately, I can't locate a model number for the microwave.) I'd appreciate having information about the "food temp control," which is on the front of the oven. There is a wire probe that goes from the inside of the microwave to the food. I assume that relates to the "food temp control." I'd appreciate having any information about how to use the "food temp control." Also, I 'd like to know wh


I serious doubt that probe would work any longer for they go out in ten tears or less ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0840 seconds