Having problems with your Vacuums ?
There is no power left in the machine re pressing the green button to start does nothing
T RY LETTING IT RESET ITSELF,,, WAIT HALF AN HOUR,, COULD HAVE BEEN A BIT HOT GEORGE
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
There is no power left in the machine re pressing the green button to start does nothing
T RY LETTING IT RESET ITSELF,,, WAIT HALF AN HOUR,, COULD HAVE BEEN A BIT HOT GEORGE ... Vacuums
Press the power button on - good got a green light (new battery) press the clean button - got a green light iRobot runs for a couple of seconds and stops, then starts, then stops. After two or three times I now have a red light on for the Status. All of the wheels seem to be clean. I used compressed air to clean the underside. But still have the start stop problem.
How many times does the red light blink before it pauses? ... iRobot Roomba Discovery SE Bagless Robotic Vacuum
Miele S5000 (revolution 5000) vacuum cleaner - How do I open the casing? When the power button on the handle is pressed the green power-level lights on the handle light, but the motor sounds like it gives a little 'jump' but nothing more. The orange power light on the body also dims. I assume the motor or fan is jammed, but I can't open the body to find out. I've taken out to screws inside near either end of the handle, but to no apparent effect. I'm assuming the body is held together by plastic
Our Miele vacuum is only 2/3 years old and seems to have given up the gost, our previous one lasted 15 yrs. The machine starts ok and within 4/5 minutes the power drops down and the hoover comes to a stop and it may re-power itself again within minutes, as of today their is no power when the on button is pressed. What do you think the problem is Thank you.
There is a circut board that is going bad and not providing the power to run the motor. You will need to contact a Miele dealer for that part. It is the only board that is in this machine so they should just need a model number in order to get it ... Oreck XL Ultra Bagged Upright Vacuum
Hoover U8311 WindTunnel2 vacuum cleaner will not run. When I press the start button, the Red dity light comes on but nothing else happens.
... Hoover U8311900 WindTunnel 2 Vacuum
Power nozzle on E-series won't start when cold unless the red 'reset' button is pressed multiple times while also holding the trigger to 'warm it up'...this is w/the power nozzle off the floor - no restriction on it turning. Once it's been running and then turned off the button must be pressed w/the trigger to get it to run - again w/the nozzle off the floor. It also seems to shut off too easily while vacuuming. I replaced the motor,which didn't fix it. Is the reset switch next on my list? T
... Rainbow E series Canister Wet/Dry Vacuum
Machine will not work, i plug it in and press the power, but nothing happens.
I have the same problem with my shark. I dismantled it and found that a thermal fuse on the bottom of the tank is blown. I am trying to locate the part now. I will post when found. ... Euro-Pro S3325 Handheld Steam Vacuum
My dyson DC05 has been playing up for a while. The motorhead would start fine with green light on and after a few minutes would stop and light would go green. then the power would go on and off - seemed to only work when I had the handle a certain way. Now no power at all. is there a way that I can check if its the power in the handle section as thats the only way you can turn this machine on? Thanks in advance
As the wires that control the motorhead run all the way down the hose it is a break in the wires you will need to buy the hose assy sorry its not thesort of thing you strip down and repair ... Dyson DC05 Bagless Canister Cyclonic Vacuum
I have a miele S712 (2 yrs old worked fine yesterday) - I had been doing some diy work inside and had the vac on just to reduce some of the dust in the air - after a while the vacuum fizzled out. I guessed it had overheated and took it outside to cool down - when I tried to turn it back on pressing the power button gives it power and it starts to **** but it won't STAY on, soon as you release the power button it stops, and the orange bag indicator is showing full. As I have a compressor I took
You have got dust in the micro switch and it is not latching on, if you look at this and clean it, that will solve your problem, however blowing the motir has probably wrecked the motor bearings. ... Miele Vacuums
I set up my ONYX SW2300XS which I recieved as a gift (so no reciept) for the first time today. At first it was working well, I inserted a dvd and it played well. I played with the zoom and the skip buttons on the remote a bit and left it playing while I went a did other things. I came back about halfway thru my movie and wanted to skip scenes but the remote did not work. So I tried the NEXT button on the machine. This did nothing, so I tried the STOP button and that did nothing, the dvd was
Mine does the same thing! The store told me it would play all formatted but it does not! Its junk!! ... Vacuums
I recently purchased a Sunbeam Artista EM5900 model coffee machine. I plugged it in and pressed the 'Power' button only to find the power go out. I understand this is short circuiting, so I went and turned the power back on. I then moved the machine to a different powerpoint and plugged it in - the same problem happened and I have tried it countless times on various other powerpoints. Help please?
Try it in a different part of the house. If it works then you have too many things running in the kitchen.\015\012If it still blows a breaker then it is shorted out and needs to be returned. ... Vacuums
It will work-about 1 in 50 times of trying. when i put in a file and press MDR button it makes a whirring sound and the screen will say any one of several things e.g.no disc or corrupt file.If the data file is put in before machine is switched on-i then get YAMAHA MDF 2 and nothing happens when i press the mdf button.
The unit is basically a floppy backup machine. In your case the actual floppy reading unit has failed. Since this is a custom mechanism it means that the unit is pretty much dead - no replacement parts for it. If you are willing to try everythi ... Vacuums
Electrolux Unirapido not working green light flashes when start button is pressed!
I have the same problem with this type of vacum. I have tried a lot of things but the problem is with the software included in a 20 pins chip on the pcb so it can not be repaired. But, if you look in the back of the vacum there is a rubber stopper wi ... Vacuums
Won't start I have a miele, model # s2481 red vacuum. It will not start. When the button is pressed it feels normal, but nothing happens, it will not start. Is this a problem my handy husband can tackle?
It is most likely your cord winder. They are a little tricky to fix yourself. A repair shop will probably charge about $50. To fix it. The contacts where the cord winder plugs into the motor need to be cleaned and adjusted. Just don't let your r ... Vacuums
My Dyson Aminal Vacuum simply will not turn on. I plugged it in this morning, pressed the power button- and nothing. No warning sounds, simply silence. Sigh. Nothing is wrong with the wall outlet.The vaccum is 3 years old but has run perfectly until this point. The brushes are clean of any accumulated hair. What part might need replacing?
The power switch may need to be replaced. Call the Dyson helpline - they will give you the location of an authorized Dyson dealer in your area who will be able to replace the switch. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Delonghi Citiz Milk frother not working. After pressing button, red light comes on and heat starts, then after a few seconds red light starts to blink and nothing happens.
Please visit the link provided below :http://www.delonghi.com.au/support/instruction_manuals/EN265BAE_im.pdf ... DeLonghi Vacuums
Simplicity vacuum My vacuum just cut off and now it wont start. I pressed there restart button but nothing happens I have 2 fairly old Industrial hitachi dry vacuum in my workshop both 110v and both wont start. Both i was told were manufactured in Italy and both have a manual and auto switch. It has a black top, takes an orange paper filter inside and its bin is dark blue. Sorry i've forgotton the model number. I've inspected the wiring but it's fine, could it be the motor and how do i gain acc
Just take it in to your vacuum store. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
I have a G.E 1.0 Microwave Model JES1039WF02, It has power on the panel but I see a message that says -F3- It will not start or do anything when the buttons are pressed. There is power running to it. The light inside turns on when the door opens. I looked through the owner's manual and there is no reference to this message on the troubleshooting section.
If there is no heating please do not switch on unless you have confirmed the fault. It is possible that the Magnetron is faulty, the temperature cut off is faulty or the main capacitor is short. It is also quite possible that insect can get ... Vacuums
The power button on my scooba will turn on but when you press the clean button it will not beep or start to clean
... iRobot 5800 Scooba Vacuum
Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i
At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum
I have a Juki serger mo-634de that I am borrowing from my sister in law. She doesn't have the manual, but just got it back from the shop in good working order. I have threaded the machine, and when I manually turn the dial, it appears to stitch properly, but when I press on the pedal, nothing happens. No sound from the motor, no movement with the needles, nothing. Help! (c: Power is working, because bulb turns on.
NO POWER My Dyson DCO4 Absolute (purple&lime) won't' switch on. I've checked the plug fuse, wall socket and also filters and hoses on machine all seem fine so think the problem is with the on/off button (maybe loose wire or something) but how do i get to it, is there a special way to remove the green on/off button in order to check the connection? Thankyou in advance for the help i am sure you will be able to provide.
The problem is almost certainly a fatigue break in the flex. These usually happen where the flex enters the handle through the rubber sleeve near the on off switch. You will need to cut about four inches off the wire and reconnect it to the switch. ... Vacuums
I have a 9068G and when I plug into the electrical outlet and press the "on" lever, I get nothing. The machine actually quit one time while I was vacuuming. Is there a fuse problem or a reset button? Thanks.
There is no reset button or fuse, yo have a clog / reduced air flow, causing the motor to over heat and turn off. First change the bag, then remove the wands and carpet tool from the vacuum. See if the machine turns on. If not the main motor will ne ... Samsung Quiet Storm 9069 Vacuum
I have a rebuilt Kirby Classic and it started smoking and now will not work. Even when it is plugged in and the on/off button is pressed it does not power on. Johanna
Get it fixed, it's 40 YEARS OLD! ... Kirby Vacuums
My shark steamer has stopped working after a year of having it (I have already replaced one, I'm a idiot!). My problem; however, is that it will steam, but the steam stops traveling through the actual "mop" part. I plugged it in, wait seconds and start pumping, but the steam builds up until it's hard to pump. I had to press the button really hard for the bottom to come off and it shot off like a rocket! I tried to stick something through the tubing, but it did nothing. What am I doing wrong? I
\012\012\012Hi,Here\012is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it\012may not be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum