Having problems with your Vacuums ?

My Eureka Uno vacuum won't turn on. Power switch

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Eureka Upright vacuum (4800 Series). When I try to start it by turning the switch on, it wont. For few days, I was able to get around this problem by repeatedly turning the switch on and off until it turned on but that does not work any more. Could it be something related to the switch it self or the power cable. My wife mentioned that one of my kids might have pulled the power cable too hard (at the back of the vacuum). Any help to solve this problem will be very much appreciated. Tha

... Eureka Smartvac 4870 Bagged Upright Vacuum

My Eureka Uno vacuum won't turn on. Power switch

... Vacuums

Eureka enviro vac 3041bz son sucked a sock up in the vacuum, its turned off. I removed the sock from the tube. Now it wont turn back on. Is there a reset switch and if so where is it located

... Eureka 411A Upright Vacuum

My Kirby G 2001 upright vacuum wont turn on. I tried another outlet and still nothing. I don't see a breaker switch anywhere. If you know of any common problems I would love to hear them. I am very mechanically inclined, I just was wondering if there are any common issues with the motors or power switches etc. so I don't waste a lot of time troubleshooting. Thanks

This might sound a bit silly but check to see if the cord is plugged into the machine correctly if it is check to see if the safety interlocks are all engaged. ... Vacuums

Eureka TheBoss SmartVac 4870 power switch no longer turns off vacuum. Is there an easy fix?

... Eureka Smartvac 4870 Bagged Upright Vacuum

Hoover Upright Vacuum model U5470-900 - The On/Off switch on the handle does not properly engage the power switch deeper in the handle assembly. It appears to ride over the lower switch and doesn't engage it to operate it. If I play with it, I can get it to maybe turn on the vacuum, but, then the upper handle switch won't turn it off. Our current workaround is to use the power cord for on/off operation.

... Hoover Vacuums

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?

... Vacuums

How do I replace the power switch please? - Eureka Uno 2998AZ Bagless Upright Vacuum

You can pry off the switch unless you have the type with screws to remove. Then disconnect the wires from the switch, replace switch and snap back in place. ... Eureka Uno 2998AZ Bagless Upright Vacuum

Vac motor runs but belt wont turn - Eureka Power Plus 4703D Bagless Upright Vacuum

Its time to check and/or change your belt. to do this you want to remove the two screws on the top casing and remove the cover. There are detailed belt change instructions on a sticker under the top casing on how to remove the brush and b ... Eureka Power Plus 4703D Bagless Upright Vacuum

I had the vacuum cleaner question about the canister and the wand/powerhead... the Kenmore Progressive Vacuum canister model 116.25812 and the canister not powering off without unplugging the vacuum. The solution I received that they both run on their own switch so it is normal makes sense. However, is there a power switch on the canister anywhere? The only way for the canister to be turned off is by unplugging it. Any ideas? One would think there would be a switch. I am new to fixya and hope

Hi. On some models, one switch controls all of the power. Your issue, which is no working switch is almost certainly a blown triac on the circuit boar ... Vacuums

I have a Eureka Boss Power Plus and the beater bar is rolling, the belt is turning, but after vacuuming up around the litter box (not a lot of litter), when I turn the vacuum off, the litter, or even household dirt, falls out. When I hold the vacuum back to turn it off so that it doesn't fall on the floor, it's sitting in the cubby where the wheels are. The bag is empty, the hose is not plugged, the hose is securely fitted on both ends of the unit. This vacuum was purchased in July and is being

Even though the brush is spinning, you probably need to replace the belt because it is s ... Eureka Vacuums

I have a Eureka Power Plus vacuum, model 4702, type A. To start off, it never really had great suction. Marginal at best. Then today I was vacuuming and smelled something burning and turned off the vacuum. At that point, smoke started pouring out from the bottom of the vacuum so I layed it on it's side and the smoke cleared but I never found the source. Is it safe to turn on again after I let it cool down or is my vacuum "shot?"

... Vacuums

Electrolux vacuum brush not turning problem: was vacuuming and rug got caught auto shut off kicked off power to brush. instead of hitting red button to restart brush I disconnected brush to vacuum some hair in Conner. after i reconnected the brush and hit the red button but no power to brush. Light won't even switch on. Hope you can help

Under the vacuum, there is a guard.\012remove the guard , either by 2 screws or by 2 clips.\012there is a belt under the guard.\012that is connected to the brush.\012the belt need to be replaced. ... Vacuums

Power nozzle on E-series won't start when cold unless the red 'reset' button is pressed multiple times while also holding the trigger to 'warm it up'...this is w/the power nozzle off the floor - no restriction on it turning. Once it's been running and then turned off the button must be pressed w/the trigger to get it to run - again w/the nozzle off the floor. It also seems to shut off too easily while vacuuming. I replaced the motor,which didn't fix it. Is the reset switch next on my list? T

... Rainbow E series Canister Wet/Dry Vacuum

Eureka cv3291k Vacuum does not turn off. Is it easy to install and purchase a relay switch? I think that is the problem as when I disconnect low voltage wires it still turns on when I plug the vacuum in.

... Vacuums

Hi. I borrowed my friend's Hoover VC340 to clean my house. I was vacuuming when i noticed the cannister was full, so I turned the vacuum off, pulled out the barrell, and followed the instructions on the barrell to empty it. I put it back into the machine, but it wont turn back on. I tried different power outlets, but to no avail. any thoughts?

... Vacuums

My lux 7000 has a new bag but when i start to use it with the power unit or without the unit shut's it self off i can reset the lites or the motor if you will by clicking the on off switch 4or 5 times and i'm ready to go again untill you start to work and off it goes you can repeat the switch thing as long as u want, it just won't let u vacuum ,it turn's it self off .I blew it all out but found nothing in it. if u don't try to vacuum it will run as long as u want to listen to it. Can you

Have you replace the afterfilter? It may also cause this if rather dirty. It's located under the tool caddy/air diffuser on the back half of the machine.\015\012Try this: Disconnect hose, turn on vacuum. Does it continue running? If so, pl ... Electrolux Lux 7000 Bagged Canister Vacuum

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu

This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

Replacing the power switch of the Eureka The Boss 4870 vacuum

Its actually just held in place with two small plastic clips. so just gently start pulling the plastic housing up. it will pop off with some force. not so much that you break anything however. but there are no screws or anything. to get it back ... Eureka Smartvac 4870 Bagged Upright Vacuum

Proteam Pro force 1500xp Upright vacuum... When I switch to the carpet setting I have no suction power but the beater bar is turning. If I switch back to the floors setting, the suction is excellent. Wondering if the problem is in the on/off switch?

Just undo the screws on the front part of the switch assembly, carefully check all the leads to the switch. Mine slide off all the time as the switch is poorly designed and subject to damage when the darn thing tips over (easily!!!) new switches are ... Proteam ProForce® 1500XP Bagged Vacuum

My Eureka Altima Upright Vacuum Model 2996AVS Vacuum wont turn on. Any advice where to start? I would think it may be a fuse but do not know where it is on this vacuum.

... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

My Eureka Altima Upright Vacuum Model 2996AVS Vacuum wont turn on. Any advice where to start? I would think it may be a fuse but do not know where it is on this vacuum.

Generally, on something with a cord and plug, the first thing I suspect is a bad spot in the cord where it connects to the plug. One way to check it is to turn the vacuum on, plug the plug into a good outlet that you have checked to make sure it wor ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Eureka Vacuum Excalibur Model 6975A on/off switch won't turn off. Probably need new switch but can't figure out how to get cover off to get at switch

... Vacuums

My brushes do not turn on my power glide pet vacuum cleaner after I accidentally sucked up the hem of a curtain. I switched off the machine then removed the hem. Now when the vaccuum cleaner is turned

... Electrolux Vacuums

Central Vacuum works when power switch on canister is turned on, but will not turn on when connecting the hose.

DOes it not work on any of your wall inlet valves? If all wall inlets appear dead take a coin making a connection with both of the contacts inside the throat of the valve. If the vacuum turns on the problem is in your hose or the powerhead. If nothi ... Kenmore Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.2604 seconds