Having problems with your Vacuums ?

Hi monarch 650 duct cleaner when we connect the hose to the point the machine start and when we take off still the machine working what is the problem Tommy

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi monarch 650 duct cleaner when we connect the hose to the point the machine start and when we take off still the machine working what is the problem Tommy

... Vacuums

I have a Bissell Powersteamer Pro Deluxe, Model 8804 shampooer. I got this bright idea to take the brush off as it was full of hair and debree. Upon putting it back on it appears I'm not getting the brush on properly. Does the belt go around the end with the grooves? Also do the grooves go on the right or left side? From my view point I am looking at the machine with it lying on it's back and I am sitting on the floor looking at the bottom of machine. Sure hope I haven't confused you too m

... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

My Dyson DC17 has lost suction on the wand and is not picking up dirt as it should. I have taken the small part at bottom of the machine off to see if there is a blockage--none that I can see. The flexible tube on wand is very tight and won't extend very much. Dyson sent me a new cyclonic part in April but the machine still doesn't seem to be working properly. My serial number is 260-us-d11545. Is there somewhere I can take my Dyson to get it fixed. I'm very frustrated with it. Thank you.

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I also have a Hoover upright and I need to replace the electrical cord. I have dimantled the back, where the tools are stored, and the hose. I still cannot find the screws or whatever, to get to the area behind the cord, so I can replace it. I think I will have to take off the bottom too. Has anyone out there tried to do this? It seems crazy. This machine works great so I hope I can also put it back together. Thanks for the help.

Since I do not know your specific model I can only supply you with general instructions. Be aware that most of the time you only need to gain access to the on/off switch to replace the power cord. Also Make sure that you are replacing the existing co ... Vacuums

The hand held dyson does not appear to charge. does the battery come away from the unit as I can't seem to release it? Would there be any point in buying a new battery as I don't know if this is the problem. The red light stays lit all the time it is on charge and when I take it off the machine does not respond at all.

The battery is located at the bottom of the handle. To release it, press and hold down the button on top of the battery case (it has 3 ridges on it). That releases a catch and you can then slide the battery out to the rear. This can be quite ha ... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum

No suction I live in a house with two bernese mountain dogs... very large animals who shed a LOT.  I've cleaned the filters, the roller, and gotten as far into the hoses as I can without taking the entire machine apart.  It's still not cleaning as well as I know it can... nothing is making it into the debris receptacle.  What can I do?

Hi elora,\015\012\015\012I live in a house with three shedding cats. I also have the same vacuum. About twice a year, I have to getinto the area of the vacuum where the motor is. There is a little pring loaded vavle that sometimes gets ... Bissell 3590 CleanView Bagless Upright Vacuum

FOR dlh2457: Just came across your post to another person's dilemma. I found this Baby Lock BL4 428 serger at a thrift store. It powers on but I know nothing about its use. I don't want to spend $14 plus for an owner's manual and find out this machine does not function properly or possibly damage it by improperly threading it or having it out of adjustment. I'm in need of an owner's manual for a Baby Lock BL4 428. If that offer is still good I'll take a "copy" of it and will compensate you for

I've found it , it costs 9.95$ , together with shipping it will cost 15.93$ at your doorstep.Bit more than 14$ but that is th cheapest one.Symply ... Vacuums

Cable stuck in machine (sphera 20). How do I take apart to release cable please? I cannot see any visible screws to take the machine apart. Cable will not retract or come out of machine

... Bosch Vacuums

Vapor Clean TR 5 Under "maintenance" they told me to unscrew to empty refill tank. After doing that, no water came out and the piece that the scew went into is now in the tank. It is too large to get out and even if you put the screw back inti that piece ir still goes into the machine. Can I still use the machine? brand new only uded it once

I is really needed to check this with the manufacturer! See contact details below: ... Vacuums

I have a Husqvarna Viking Designer sewing machine. The fuse blew in the machine and I am having trouble finding a replacement fuse. It is a T3.5/250v glass fuse. Please let me know where to find one. I have searched the internet high and low and can't find one. Radio Shack has a 3.0amp 250v slow blow fuse whick seems to be the right dimensions. Willl that work. Otherwise, I am not sure what to do and can't afford to take the machine to a repair show. Thank you.

That fuse will work no problem. There is no harm in trying it.The machine probably requires about 2 amps or less under normal operation. Being a 3.0 amp slow blow fuse, it will withstand short bursts of extra current when your machine get ... Vacuums

I want to recharge my Philips PET741 D/05 portable DVD Player. But when I push the plug into the charging point on the side of the player,at one point, as the plug goes in, there is a quick flash of red - but no more. The red charging light does not light up, and the player does not charge. The plug cannot be held at the point where the sudden momentary flash takes place

1.With the AC power unit plugged in to the wall plug into your dvd player and wiggle it a little bit and see if the light goes on or off. If so the the power port is bad. \015\0122.Try a different wall outlet to see if it helps.\015\0123.Ensure there ... Philips Vacuums

I have a Yamata GK367B refurbished machine, an older model and the manul is mostly in Chinese and very bad pictures. I need better information about how to thread my machine and to set the tension correctly. I am a professional and need this machine. But it has never worked correctly since I bought it and the company will not take it back. So please help me. Jill G. Arellano

We have no material at all for this brand, sorry. ... Vacuums

Have a spin scrub a couple of years old. Have used it maybe 5-6 times and the green brushes only spin if you take the tanks off and set the machine upside down and push the brushes toward the machine... the second you stand the machine up they quit spinning.

Repace the belt ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hi. I have Dyson dc08 hepq+. Thet problem is its not having suction .I checked inside the pipe and foot , ery thing is fine. And if i take the whole dirtbin out ...machine workes fine. when i put ery thing back ....as soon as i start it , after 2 second machine change its voice...and loos suction. I think its just happen because ...the saftey yellow valve inside the machine turns up because the dirt drum is blocked inside some where. Any suggstion ...what can i do with it. I m tahnkful in avance

Hi its Darran at Dyson.From your description of the problem, it sounds as though the bin inner is missing. To confirm this, if you remove the cyclone and bin from the machine, then separate the 2 pieces as if you were going to empty it, w ... Dyson DC08 Hepa Allergy Bagless Canister Cyclonic Vacuum

Hoover Floormate H3000 stopped working during usage. Took fill take and solution take off to allow vacuum to dry fully. Still did not turn on. Any ideas would be great!

If it doesn't turn on at all, then you may have a bad switch, cord or motor. ... Vacuums

Changing belt How do I do that? It looks like I would have to take the screwdriver to the bottom and enter the engine compartment. I'm not sure that I feel confident to take this machine all apart and be able to get it back together again.

Its not the engine compatment take the screws out the cover 4 the roller will come off then u can c where the belt goes ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?

... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Dyson dc17 hose will not come out/ handle wont release from machine. i've pulled the metal rod up all the way and the handle still won't come away from the machine so i can't use the hose and attachments. anyone know what the problem might be?

Hi there, it is possible that you have a blockage in the wand/hose assembly which is making this difficult to remove. If you are able to remove it to check for this, please contact our Helpline on 1866MYDYSON so that one of our advisors c ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Sebo X4 is squealing when pulled back. Takes a while after it's been running for this to happen. We changed the roller brush (needed it anyway) but didn't take care of the noise. Could the wheels be making this sound? At least that's what my staff thinks is going on... I own a commercial cleaning company and all we use are sebos... they're an amazing machine!

Yep - we think Sebos are pretty good too. I work at a Sebo sales and repair dealership! The wheels are a good bet - I can't think of anything else that might cause the noise. If in doubt, I suppose you could simply wheel one around for a while when s ... Sebo X4 Bagged Upright Vacuum

The Hoover Steamvac Widepath will NOT pick up water. The dispenser with cleaner DOES have water. The TANK that would receive the dirty water is NOT full. All tanks are on properly and the machine will still not pick up the used water. I found a tear in the interior hose leading to the receiving tank and repaired throughly with electrical tape. Still will not pick up the water. Any suggestions?

Sounds like a clogged air path (no vacuum action) from the floor pick-up to the collection tank. Take the tanks off and deal with the vacuum problem alone. The collection tank should have a air exit vent--is it clear? Check the interior hose that you ... Hoover F6213-900 SteamVac Agility TurboPOWER Steam Vacuum Vacuum

I have a 6550 that just stopped working. I had the on/off switch tested to find out that it was dead. I replaced it and still the machine does not work. Could the wiring in the handle be bad? How do you test if the motor is still good?

I test a motor by taking an old vacuum cleaner cord with alligator clips on the ends and hook it up to the motor simply bypassing the entire vacuum cleaner. If it runs then I know the problem is not the motor. ... Simplicity Vacuums

How do you take of the base to change the belt? I removed the 4 screws but still cannot take the base off. I do not want to force (break) it... THANK YOU

If it's an Electrolux power head there will be a 5th screw same length in the base.2 at front corners, 1 front center, 2 mid way back all recessed. Good for asking , do not pry it should pull apart in you hands starting at the front corners ... Electrolux Vacuums

Hover Elite Rewind I've only had this vacuum a few months and I really liked it until now. There is almost no suction from anywhere in the vacuum, and I've cleaned all the filters and rollers with my shop vac and made sure that everything was assembled correctly. It used to be really quiet now it is quite loud and it keeps over heating, and shutting off. At this point I have no idea what could cause this problem, the machine is nearly brand new and I can't afford a new one at this point.

You have to clean out the hose under the bottom of the vacuum cleaner. To do this you have to remove the bottom plate the covers the brush it has about 6 screws. Also remove the brush and belt in order to thourhly clean it. I had the same issue you h ... Vacuums

Hello, I have an Electrolux vacuum. In desperation, I vacuumed up some water and my machine stopped. I am hesitant to take the machine to a repair place for fear that if it is a simple repair they will not be honest. Can anyone give me advice on whether this is a problem that requires a new motor or major repair? Thank you!

Although it's never to be recommended, it is sometimes possible to vacuum up a little water without doing significant damage. However, the fact that your machine then stopped suggests that the electrics got wet. That may or may not have caused expens ... Vacuums

Motor problem machine is smoking/burning smell coming from the bottom of the machine. Motor still turns but doesn't make much sound; and soulution won't squirt. The model # is 1970

I had to throw the machine away before it burned my house down. There is no way to fix it; had to replace it. ... Bissell 1770 Quicksteamer II Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0840 seconds