Having problems with your Vacuums ?

Sears kenmore 158.321 sewing machine first broke a needle, needle was relpaced, then next needle bent, needle replaced. Now the thread wont catch in the material . it isnt sewing


Answers :

Make sure you are inserting the needle correctly. The flat side goes on the left and the thread goes from right to left through the needle.
Good day!!!

If the problem is always broke the needle..

The problem could be the correct timing of the machine please adjust the timing of your sewing machine to fix your problem...

Thank you and good luck..
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Sears kenmore 158.321 sewing machine first broke a needle, needle was relpaced, then next needle bent, needle replaced. Now the thread wont catch in the material . it isnt sewing


Make sure you are inserting the needle correctly. The flat side goes on the left and the thread goes from right to left through the needle. ... Vacuums

My Kenmore sewing machine timing has gotten off. I am sewing a big upholstery project and it starting bunching thread from the bobbin. The thread is so heavy that I had to put some pressure just to get it undone. This happen a few times and then I found it wasn't sewing at all. When I evaluated without the materials in place I could see the needle would catch on the white plastic piece under the bobbin and the thread would not catch on the metal arm. It appears to be off by 1/4 - 3/8 inch.


HelloDisassemble your bobbin case which is realy quite easy, clean\015\012thoroughly with a brush and air, paying particular attention to any\015\012rust that may have formed, and any thread that may have weazeled it's\015\012way into sma ... Kenmore Vacuums

Janome 6600 sewing machine. bobbin thread is gumming up underneath on a swimsuit knit type material (4 layers). Brand new machine had 1 1/2 weeks. Sometimes material goes down into the bobbin area jammed by needle. What am I doing wrong?


Make sure you're using a polyester thread (I use maxilock serger thread) then a stretch needle, and hold the tails of your thread until you get started into the seam so the fabric cannot push down into the opening on the throat plate.\015\012 ... Vacuums

I have the Janome 6600 P. Beginning a seam the thread knotted and the machine made noise and needle would not move either up or down. I manually moved the needle using the handwheel and cut away the knotted thread. I began sewing again but instead of starting at the edge began about a half inch down, forward stitched, reversed to lock threads and problem repeated and received the message to "Stop for safety purposes". Did that. Referred to the manual, tried manual recommendation. Did not work. I


... Vacuums

Needle not catching bobbin thread


... SewShop.com Singer Model 6412 Millennium Instruction Manual

I have a Continental Electric portable sewing machine and I can't get the bobbin to thread into the machine to start sewing. How do I place the bobbin and where does the thread need to go for the need to catch it?


... Continental Vacuums

I have a Singer Model #4562 sewing machine. I am having trouble adjusting the tension. Everytime I try and turn the knob to adjust the bobbin just gets looser. Right now it just snags and gets caught underneath the material and bunches up into a big ball. There is a lot of thread inside the bobbin case that came out of the bobbin and has to be cut out to free the material. How do I fix this mess. I am a novice at this. I have not sewn in several years and would like to sew a few quilts


... Vacuums

My machine wont sew properly I broke the needle awhile ago and now it wont sew propery was hoping a manual would tell me what is wrong


Your possbly out of time ,meaning the machine isnt in synch after such a big event. check the website for putting back in time otherwise ,disconnect it off the drive and try and put it whare it needs to be ... Vacuums

Singer 327 lower bobbin thread is wild and loopy after I sew...top stitch fine. Just changed to a large thread spool with the heavy remote base and crook to carry thread to machine and wonder if this changed tension (set at 4 and correctly threaded)? It had been working fine in zigzag but I also went back to reg foot and set stitch width at 0, center needle set. Thanks for your input and help. Deanna


... Singer Vacuums

Borrowed Brother XR7700 Sewing Machine 1st: Sewed one inch OK; moved fabric and it stopped sewing, motor made thudding noise. When push-button (NOT pedal) is used, gives error E6, consistent with motor noise. 2d: In order to check threading had to manually PULL bobbin case toward me or it was UNDER needle plate. Cleaned a fair amount of dust out. Reinstalled bobbin, etc., per manual, rethreaded. 3rd: Will sew 2-3 stitches, then packs up again just like in 1st instance above. Have st


Have you checked your needle. it could probably be bent somehow. you should replace it first because that also can confuse the sensor causing that error.regards ... Vacuums

It wont let me sew,because it wont pickup the bobbin thread


... Singer 7462 30 Stitch Touch & Sew Machine

While using the pin stitch , the machine has started skipping stitches, knocking loudly, the top thread is breaking, sometimes thread knots up on the underneath side. I have cleaned bobbin area, changed needle and bobbin, using quality thread, the last time I used machine worked fine, yesterday when I started sewing I had this mess HELP!


Hi,Please go through the link given bellow to have the resolution to your problem...\015\012http://sewing.about. ... Vacuums

Bobbin not threading through, spool thread is gathering in bobbin catch and not sewing - just clumps of thread


It would appear to be threaded wrongly. Pull all the threads out, check the visible upper tension discs for broken threads then re-thread top and bobbin, making sure the pressure foot is up when you re-thread. Bobbins should normally turn clockwise ... Vacuums

Janome sewing machine Harmony 2139 The bobbin thread is not connecting with the needle to make a stitch. We have put in a new needle. Using needle 4 tension


A common problem is if needle is in backwards. The small groove side should be toward the operator. As the needle starts back up after going clear down, a small loop should form on the side of the needle away from teh operator. The shuttle has a p ... Vacuums

The last time I sewed with my Necchi the tension was fine. Today when I threaded my needle, the thread felt tight in the upper tension dial. I tried re-threading the machine several times, but it didn't help. Now the parts of the tension dial are all loose and wobbbly and I have no upper tension. Doesn't matter what the dial is set on. The tension dial appears to be broken, but I don't know how that could have happend since I store it in a case.


I found this thread (no pun intended):\015\012\015\012http://www.fixya.com/support/t2902978-need_replace_upper_tension_dial\015\012 ... Vacuums

How to thread a Singer 5705 6 Stitch FLATBED Sewing Machine properly? the thread falls out of the needle when i start the peddle


... Vacuums

The needle keeps breaking on my Janome J3-18 sewing machiene and the thread tension seems too tight. However the tension is set at 5 and it is standard thread and I'm using standard fabric. What's going wrong?


... Vacuums

I have an expression 2038 and the stitching has suddenly changed so that the top stitching is quite good but the underneath is loose. I have the tension on 4 and have a new straight needle and good quality thread. the underneath or bobbin thread is almost not catching.


If the bobbin thread is too loose, remove the bobbin spool AND carrier.Thread the thread through the tension clip on the holder in the normal way. Hold the thread and lift it. If the bobbin slides down, tighten the small screw 1/8 turn clockwise, u ... Vacuums

I have a janome BCC-30 sewing machine and the upper thread has started to break and fly out of the needle while I am sewing. The problem continues even when I change the tension dial.


... Vacuums

HI I have a Necchi Super Utility sewing machine and it has suddenly stopped picking up the thread from the shuttle. I have recently been sewing some quite heavy leatherette material, could this of caused the problem and do you know how to fix it?


... Vacuums

Top thread does not pick up bobbin thread, also clicking sound when needle is down under plate, as if it is hitting something. Please help I have a job to do! This machine is new it's a Singer Inspiration Model 4228. It worked just fine until I finished my first sewing job on this machine. I'm hoping you can help me! Thank you, CD


... Singer Vacuums

Sew- Prow Sewing machine Model ZZ- 401 need diagram to order part and manual. Has broken missing parts in spool area spool wont stay in under needle Davy B


Hi!!\015\012\015\012Try this sites\015\012Hi!\015\012\015\012It seems that this is a common problem for this machine. I think you will be better off getting a new machine for $50 at this site\015\012 ... Vacuums

What size needle and what type of thread would you need for sewing marine vinyl if using a pfaff 130 sewing machine?


I had a friend who used to use nylon thread. He had been using a number 16 needle and heavy duty \015\012thread(top spool only, reg. thread in bobbin) On the first vinyl, \015\012it worked well. The second vinyl was causing the bobbin thread to " ... Vacuums

I have a janome sewing machine 432S, sounds like it needs to be oiled, but I don't know where, and it keeps breaking my thread at the needle


... Vacuums

Thread at needle breaks when sewing. - Vacuums


Most common problem is the quality of the thread, most sewing machines require quality thread or else it breaks especially if the material is thick or hard ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0418 seconds