Having problems with your Vacuums ?

At first when I tried starting my B & S I primed the motor and it ran for a few seconds and died. This happened twice. I drained the tank and took apart the cvarb and blew out the entire carb. Put it back together changed the plug and now nothing. Could it be that the priming diaphriam (#694395) has a hole and thus preventing gas to come up from the carb bowl?


Answers :

Hi tifix1...
\012Yes, that could cause your problem.
\012I will offer a few more things to check and repair/replace, maybe there is a few things that you missed.
\012Please take time to rate me
\012
\012Sounds like you have dirt/debris in your caburetor jets,fuel passages or a diaphgram that is becoming non-flexible.
Check/Clean/Replace your Air Filter, a dirty air filter can make your engine run to rich with fuel.
\012Note: ALWAYS USE COMPRESSED AIR TO CLEAN YOUR JETS AND PASSAGES, VERY IMPORTANT.
\012Note:Before you disassemble the carburetor:
Mark each piece with a awl, or some kind of instrument that will make an alignment scratch before you disassemble the carburetor into separate pieces.
That way you will know which way it goes back together when you reassemble it.
\012Sometimes you can get by with priming the carburetor or by using starting fluid and letting it run a few times like that, and it will flush the gunk out of the jets,but most of the time you will need to rebuild the carburetor.
Check you fuel line condition after a while they will degrade and need replacment.
\012Check/Clean/Replace your fuel filter if you have one.
When you remove your fuel lines from the carburetor be sure to make a drawing to how the lines are connected to the carburetor.
Normally the big line will be the line the fuel filter is connected to inside of the tank.The smaller of the two lines is the return to the fuel tank from the carburetor after it is pumped thru the carburetor by the primer bulb.
Make sure you are using fresh fuel...and oil mix if your using a two cycle mower or weedeater with the oil to the right mixture and not too much oil as it can cause hard starting.
If the trimmer is over a couple of years old, then I recommend that you buy and install a new carburetor repair kit,because the diaphragm will get hard and that will cause it to be hard to crank.
The diaphgram may look good and flexible, but it can be deceiving and not act as a fuel pump as it should because it has become too hard and will cause hard starting,start and run and shut off, etc.
\012When you clean your carburetor, I recommend that you use a laquer thinner type cleaner to clean and dissolve the laquer build-up in the float and needle jet passages.
Be sure to remove all plastic and rubber parts before using the laquer thinner because it can dissolve the plastic parts and render them unuseable.
Be sure to use COMPRESSED AIR to blow out all the fuel and air passages.The higher air pressure is needed to blow some of the trash/debris from the fuel or air passages.
Be careful when blowing out the passages, because there are sometimes small rubber type seats in the bottom of some of the passages.
Keep in mind that the float (if you have one) for the carburetor must be level when you go to reassemble the carburetor or follow the instructions you get with the carburetor kit, or you could also ask the parts man that you get your kit from.
When you clean your carburetor and remove the jet screws, you will first need to lightly seat the jet screws.
But before you lightly seat the jet screws count the number of turns it takes to seat the jet screws from their original position.
Be sure to mark the turns down on a piece of paper.
That way when you put the jets back in, you know to lightly seat them first and then turn them back out to their original position before you started.
Note:
The little spring inside of the carburetor goes under the float arm.
That is where your fuel inlet needle/float valve is located...on the arm at the end.
Normally there is a small indetion in the carburetor base and a small protrusion on the underneath of the float arm where the spring will be in the right postion for installation.
The spring will set in the indention and you will install the float arm with the needle/float valve and float rod into position over top of the spring,you will push down until it is in position and then you can tighten the screw that holds the float arm assembly in position.
Once you have your carburetor cleaned/rebuilt that should solve your problem.
Please take time to rate me
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

At first when I tried starting my B & S I primed the motor and it ran for a few seconds and died. This happened twice. I drained the tank and took apart the cvarb and blew out the entire carb. Put it back together changed the plug and now nothing. Could it be that the priming diaphriam (#694395) has a hole and thus preventing gas to come up from the carb bowl?


Hi tifix1...\012Yes, that could cause your problem.\012I will offer a few more things to check and repair/replace, maybe there is a few things that you missed.\012Please take time to rate me\012\012Sounds like you have d ... Vacuums

Ive got a dc07 dyson just changed the belt on it as i had to since then it isnt picking anything up at all nothings clogged up had it to bits and put it all back together again properly. The hose is working when i take it off its got plenty suction but when i run it along the floor it picks absolutely nothing up any ideas that i havent thought off. Thanks


Sounds like the hose underneath has become detached. Have a look and if its not that come back to me. Also can yo9u check your U Bend is still on as these can come off. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

While using my mop yesterday, it stopped letting steam come out. Tonight I plugged it up again and you could hear it trying to steam. I push the button in to release the square frame and it pushed out a burst of steam and pushed the head off. Put it back together and it still will not let steam out. No matter how much water is in it.


\012Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Ste ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

My daughter pulled to hard on the ceiling fan pulling out the chain. i have taken it off and apart, nothing appears to be broken but im trying to figure out how to put it together so it retracks, i assume it has something to do with the tension of the small spring inside of it, but not sure how to put it back together im wondering if there is a internal diagram of this ???


Don't even bother to repair the pull chain switch, get a new one at KMart, HomeDepot or similar store for less than $2.\012\012Two times I've repaired one, it comes apart when I need it the most.\012\012Good Day! Don't forget to rate thi ... Vacuums

Replaces the belt on dirt devil dynamite pluse model put everything back together started it and it burt the new belt up that fast. I put it around the beater brush and the metal bar I thought it should go around, yet it seemed like there should be something else there to put the belt on. What do you suggest? Do you have picture I could go by?


The metal bar you put it around if the bar itself does not spin it is going to burn the belt up. Every thing that the belt is supposed to go around has to turn or the belt will rub on the piece not moving and brake. ... Vacuums

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Search for bissell pro heat pump. bissell.com will not have it ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Pump part number is 2107181, the diverter valve # 2136988. You can Bissell and they can tell you who may have parts near you, or you maybe able to order thru Bissell.com. Before you took it apart, were you getting water to spray out of the hose. I ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

How do i put my sentria back together after changing band


See utube video for refitting ... Kirby Shampooer Shampoo Hose G3 Ultimate Diamond Vacuum

Bissell Pro Heat 7901 will spay through hose but not the floor and red flow indicator will not spin. So we took the housing off and after unclogging a hose running to the hearter, my husband unhooked the hose that goes to the flow indicator, blew in it and it started spinning. Put the deep cleaner back together, tried to use it and nothing. What else can we try? Can't afford to put it in the shop right now. Thanks in advance.


I borrowed my friends bissell to clean my carpet. It's the 7901. He brought it over and told me that it only sprayed out of the attachment hose. He said he couldn't figure out what was wrong. I'm no vacuum technician but, I am a mechnic. I decided to ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...


The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

No suction I have the central vac type. It has no suction at the can. I pulled the hose going to the walls and tested there...and nothing. I removed the dirt can and checked the motor ...it is spinning but does not feel like any suction. I checked the exhaust and it is pushing strong air out. I also cleaned the filter and still nothing. Is there a relay or something that would cause only exhaust air. I emptied the can of dirt and put it back together and have absolutely no air.....hear the motor


On some units there is a screen that protects the impeller of the motor. If this gets sealed off with debris then it is like putting a potato in the tail pipe of a car. Taking the top off the unit reveals the motor. DO UN-PLUG the unit first from th ... Electrolux Central Vacuum

I have a Kenmore 116.36932 (upright-bagless vacuum) that the motor protector by-pass valve has opened. I've clean out the area between the agitator brush where the flexible extension hose starts. There was some blockage there. I checked the rest of the system (extenstion hose, back filter area, pipe area to canister and area to side filter. I took the 2 filters out and the by-pass valve is still open. Where else could there be a blockage that I can take apart to clean and put back together


... Vacuums

I have a kirby sentria and after I shampoo'd the carpets I put it back together to be a regular vacuum and now it wont turn on. Any ideas what could be wrong?


The only thing I can think of is the brush head is not on properly.If the head is not aligned right,then the saftey switch wont be activated.Otherwise,I'd say the saftey switch or power switch.Did you make sure not to run over the cord? ... Vacuums

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o


Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I cannot find the directions for my Utilitech 1-outlet timer. It has two numbers on the back: #148297 and #TMO1DHBL. I thought that I could just put the time now arrow on the present time and pull up the sections when I wanted the timer on; the only problem is, it lights up whenever it is plugged into the outlet. I just need the directions for setting the timing. Thank you very much Lilla


... Vacuums

Oreck Upright Hi Redev, I'm not sure what model I have (about 6 years old...upright, looks like the one in the picture). I changed the belt (which was torn) and then the next time I used it, it cut off on me. Now if won't turn on at all. (I turn the switch on and off and nothing happens as if it is not plugged in but it is!). I noticed at the top where the power cord enters the handle, it is all frayed. Could the electrical wires have detached? Anything you think I should check before taking it


The cord could be bad and will ahve to be replaced. It would have to have a problem inside the handle or down by the motor. ... Oreck XL2600 Vacuum

Trying to change bottom belt for rotater brush and cant figure out how to put back together


Here is a link to the manual and the belts you need.Bissell 1694 Manual and Belts ... Bissell Powersteamer 1694 Upright Vacuum

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

We had to take the bottom of the vacuum apart to remove dirt that had plugged the hose. We cannot put it back together so that the smaller round belt stays tight. I need a diagram of how this belt is supposed to fit.


Most vacuum manufacturers avoid putting their shop manual in the public domain. There are various reasons for this, some good ones.\015\012But I did find this. Maybe it'll help.\015\012 ... Hoover U6441-940 WindTunnel Bagged Upright Vacuum

Need the manual on how to run (put together and all) the hoover steam vac v2 (widepath) with auto rinse) we tried today and when we leaned it back (so we could run it on the carpet) water started pouring out all over the machine and got the carpet (like flooded) wet :( this one was me mom's and she passed on approx 2 1/2 years :( she always kept the manuals for everything but we caint find this one :( ... thnx


God Bless Your Mom.\015\012\015\012Hope this was helpfull to you. Sawdust46\015\012\015\012http://www.hoover.com/pdfs/manuals/F7411900.p ... Vacuums

What causes these things to become unbearably loud? We've cleaned evey filter on the machine, pulled every speck of hair and lint off the brushes, changed the belt, no clogs anywhere. I've totally (and I mean totally, down to the brushes on the motor!) torn this thing down and put it back together with no difference. Also have a Eureka bagless, and after minimal use, and almost anal retentive maintance, it does the same thing,to stinkin loud. Wish one would **** up the other to save a trip to th


A clog in the hose or dirt inlet by the brush roll will cause the motor to sound loud. But so will a bad motor bearing, or motor fan, in which case you would have to replace the motor. ... Bissell Vacuums

I just purchased a Dirt Devil machine on Monday, I finally got it put together today and the brushes are not moving, dust is swirling around but no brush movement, I have changed all the nap settings, nothing, I am having company tomorrow and I threw my other vacuum cleaner away, HELP ME. Thank you.


Sounds like you may not have the belt attached or it is broke. ... Dirt Devil Vacuums

LittleGreen Machine Pro turbo brush put back together


Here is the web site with the parts breakdown.\015\012http://www.marbeck.com/carpetcleaner_parts_bissell.html ... Bissell Vacuums

I own a singer sewing machine model 4562 and tension assembly came unscrewed and now I don't remember how to put the pieces back together. Do yo have a diagram that can be emailed to me so I can put it back together? Thanks


... Vacuums

I need to put my kenmore vaccum back together I took apart the lower unit to get the roller it got gunky and all around the roller got gunky, Now it;s a bear to put back together


Remember the last thing you took off and start there,work your way in reverse towards the first thing you took off ... Kenmore 25512/ 25513 Progressive Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0940 seconds