Having problems with your Vacuums ?

How to remove brush roller bottom plate

\015 I have removed two long screws the other two are loosened but not completely removed I want to take the bottom plate off to get at the brush roller\015

Answers :

Make and model ??????
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to remove brush roller bottom plate

Make and model ?????? ... Vacuums

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom

Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Last night as I was vacuuming, I noticed that the belt stop indicator light was on. I pulled out the hair that had gotten tangled around the brush in hopes of solving the problem. It didn't change things. I then unscrewed the entire bottom piece to take out the brush roller. I removed hair from the end piece of the brush roller and reattached the belt; however, I cannot figure out where the microchip is supposed to go so that I can reassemble the base piece by screwing it back together. It seems

Not sure what you mean when you refer to a "microchip" but maybe it is a sensor that works with the belt.\015\012Anyway, if you Google the make and model number of your vacuum you can probably get an exploded view or owners manual that might indicate ... Vacuums

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help

The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Brush roller won.t turn. It turns for a sec. then shuts off. I have cleaned all clogs. This is a shark navigator. Can I remove bottom of vac to access the roller? The manual doesn,t mention this as a solution.

... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum

When i removed the bottom panel to clean out the roller brush, the front wheels fell off. I can't figure out how to put them back on!

I( think Dirt devil wheels are held on by a little clip, kind of round ish. Check the other wheel and see if it has that kind of set up. Chris ... Dirt Devil Featherlight Bagless Upright Vacuum

Belt How do you remove the bottom plate to replace the belt. I have the brush off but can't figure out how to get to the other end to loop the belt

You need to take the top cover off to get to motor shaft. Some had a couple of screws from the bottom, others had tabs, use a flat blade screwdriver to fit into the slots at the bottom edge of the top, pry out and up to pop the cover off. ... Hoover Commercial C1403 Bagged Upright Vacuum

How do you remove the bottom plate to get a the belt for the roller

Have a look at the top cover you shuold have some screws in it remove them and lift off the cover to get to the bottom brushes ... Hoover Encore Supreme Energy U4293-930 Vacuum

How do you replace a belt on the a Simplicity Synergy vaccuum? Removing the 2 screws on the bottom plate allows you to access the roller, but doesn't give you access to the drive motor. Any ideas?

... Simplicity 7850 Premier Bagged Canister Vacuum

I have an old upright hoover vacuum. I need to change the belt but can't figure out how to get to it. The bottom plate over the roller brush comes off but I can't get anything else off to get to the other end of the belt.

Model no. req ... Hoover Vacuums

Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.

... Hoover Tempo Widepath Upright Vacuum - Blue

I have a eureka bravo upright model 9600. I have removed the hood . I need to remove the brushe roller to install a new belt. I cannot figure out how to remove the brush roller.

Check out this URL:\015\012\015\012http://www.svcvacuum.com/beltrep2.html\015\012\015\012looks like it has just what you are looking for.\015\012Would appreciate a thumbs up on this if you find it beneficial.\015\012Paul ... Eureka Vacuums

Hi, I have not owned my electrolux pronto 2 in 1 for very long but the roller brush has stopped turning. The handheld part works and the green light is on. I have done a thorough cleaning of the roller brush and all other removable parts. What might be causing the roller brush to not work? Thanks, Jen

Check the end cap bearings ... and replace the belt even though it may not be broken. Put a drop of sewing machine oil (no more) in each end cap bearing. ... Electrolux EL1000A2 Pronto Bagless Stick Cyclonic Vacuum

Roller brush removal kirby g upright

GO HERE > http://www.youtube.com/watch?v=At7tqnjD-Kc ... Vacuums

I was vacuuming my room and all of a sudden I hear this loud noise, then notice the roller brush isn't spinning. Thinking too much hair was caught I separated it from the rod and hose to clean it out, but noticed that the roller brush didn't move at all while I was cleaning it. I've cleaned the brush before and it would roll around with little effort, but this time I couldn't move it at all. After removing hair and string I put the vacuum back together and started it up, but the noise continued,

It sounds like if the rod is clean then there is debree inside the roller where the rod fits in too. ... Hoover Platinum Cyclonic Bagless Canister Vacuum With Power Nozzle

Roller Brush on Electrolux Nimble vacuum not rotating.

... Electrolux 5740 Upright Vacuum

I have a DC14 with a bad belt to the roller.How do I remove the clutch that operates the belt to turn the roller. I am holding the assembly that houses the clutch and all screws are out, it appears the red knob that engages the drive to operate the roller brush must be removed. Please advise and how. Thanks, John.......[email protected]

You need a special tool to remove the clutch. Contact the Dyson Helpline so that they can refer you to an authorized Dyson dealer in your area who would have such a tool and who can fix it for you. The alternative is to purchase a tool and visit YouT ... Dyson DC14 Bagless Upright Cyclonic Vacuum

I have a Hoover V2 Windtunnel and the brushes are not turning. I have removed the black plate, removed the 4 brushes, now what?

Check for hair / fibre lodged in machine and brushes, remove it then re-assemble ... Hoover F7220900 SteamVac V2 Upright Vacuum

My dyson C07 ANIMAL is making a loud clatter noise when I push the head down. I have removed the sole plate and the brush bar is cracked so I removed it, but I understand the clutch maybe a problem also from reading other people's comments..how can I tell if it's a clutch problem also? Or... could it be just the brush bar being cracked that's causing the loud noise?

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I got a cord wrapped around the roller brush and after removing it the roller brush won't turn.

Should have smelt a rubber smell at the same time. The rubber belt probably melted in half. Just flip vacuum over so you can see the bottom. look for arrows pointing to clips or screws. Usually requires removing one panel and the brush. Buy new belt ... Electrolux 5740 Upright Vacuum


If you go to this URL:\015\012\015\012http://media.dyson.com/downloads/us/floorcare/manuals/dc17_opmanual_usa.pdf\015\012\015\012you can see a diagram on how they suggest to take the plate off and clean the unit.\015\012I hope this will o ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I unscrewed the roller brush protective cover and removed the brush to clean it. Now the roller won't turn because the drive shaft is not turning. Is there a reset button or something?

I looked at the pictorial of this vacuum at this URL:\015\012http://middleeasten.bissell.com/images/UserGuides/3750.pdf\015\012\015\012This shows the belt to slide on the motor drive pulley and also on the brush. If the brush is bound up on th ... Bissell 3750 Lift Off Bagless Upright Vacuum

Roller Brush How do I install the roller brush. I didn't pay attention when I removed it and now when I attempt to vacuum my low carpet it doesn't seem to be working. The green light on the head of the vacuum goes out when I click it down to the floor. It didn't used to do that. Plus I think I smell something burning. Could the belt be broken?

Try a new belt. The ends of the brushroller are different sizes, so you can't put it in backwards. There are numbers and notches on the ends of the brushroll. These notches/numbers need to match on both sides when installing it. (probably need b ... Kirby Ultimate G Bagged Upright Vacuum

Roller brush on Dyson D25 not working. Have removed roller brush and cleaned it as per instruction booklet advise. But to no avail.

... Dyson DC25 All Floors Bagless Upright Vacuum

I am having problems with the roller on my Oreck DTX-1300. It turns on and off intermittantly while I'm vacuuming. I have completly taken it apart and cleaned and inspected the roller unit.(I am very much mechanically inclined) This has stumped me, I have checked the electrical from the vacuum to the floor unit, and everything else that I could think of. Question: what does the metal sensore plate on the bottom of the roller unit do?? Anything anybody can tell me, I would greatly appreciate. Cap

... Oreck DutchTech DTX1300A Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0574 seconds