Having problems with your Vacuums ?

Replace motor taken apart putting back together dont know what coulr wire goes to which from the heating ellement


Answers :

Green is always ground. white or gray is always neutral. and black, red always hot. without know what make,model machine your working on this is best info i can give.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Replace motor taken apart putting back together dont know what coulr wire goes to which from the heating ellement


Green is always ground. white or gray is always neutral. and black, red always hot. without know what make,model machine your working on this is best info i can give. ... Vacuums

I have a dyson animal dc17 vacuum and it totally died. Now I can't figure out which wires go where when I install my new motor. (motor #: 160906G) Do you happen to know where the various color wires go or a place I can see a diagram of the motor with wires attached? I should have taken a photo of it before tearing out the old motor. I don't know where to connect the three coming out from the upright portion of the machine and the red seems to go to a switch (?) and there is a black (connected t


... Vacuums

Wiring diagram took wires off motor and do not know which goes where.There are two main from plug in one whit one black then two of same coming from light in front.On the motor ther are more terminals than wires.On diagonal corners there are black dots.Can you please help this cost 800$ and do not want to burn the motor due to crossing pos and neg.Do you have a picture or know where I can find?


... Oreck XL21 Bagged Upright Vacuum

I have an antique 8 arm chandlier and want to put it up in my bedroom but the wire hasnt any differance in color, how do i wire it to the exsisting wire from the celing , what wire goes to what wire ? I wont be installing it myself but would like to know so i dont sound so silly


Starting with the proper wire gauge, always white to white and black to black. ... Vacuums

Numatic Henry Hound Turbo Head stopped working. Checked wires and contacts and cleaned. lOOKED AT THE MOTOR IN THE HEAD BUT DONT know how to check it is working


... Henry Numatic "" Canister Vacuum

Motor wiring My Vax VS19TL motor died and I have managed to get hold of a new Vax 006 Turboforce motor which is the same size . My problem is that the original motor had two wires (black and white) which ran to the PCB switch. The new motor has three wires (black, white and yellow). I have ordered the PCB wiring loom for the 006 motor but I can't find any documentation that tells me where each wire goes. Can anyone help?


... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

I have a clarke bench grinder model 1002. I have a light that I would like to attach into the wiring though the grinder wiring in it's base. The light has two wires, and the grinder has a ground that is grounded to the base, a black that goes to a switch then to the motor. The white goes directly to the motor. where would I have to splice in the two wires from the light? I have a switch that I would like to put in for the light on off also.


Attach the white wire on your lamp to the white wire on the grinder.\012Attache the black wire on your lamp to the black wire on the motor side of the switch.\012This will give the lamp power any time the grinder is turned on.\012Yo ... Vacuums

Sponge filter I have a kirby sponge filter for my Sentria shampoo system and dont know where it goes. It stop working and making foam. Kirby sent me the sponge filter saying this is what i need and i would know where it goes. I dont nor kind I figure it out. please help!!!!!!!


On the end of the shampoo tank where it attaches to back of motor where the bag is normally attached ... Vacuums

Hi I have the Ambassador 337 model. I had to rewire the on off wiring due to the "N" wire rubbing through & breaking. I have it all together again although a piece of wire in the shape of a "V", with a bend each side of it has dropped out & I don't know where it came from!!!! Please send me diagram of this model so that I know where it goes. Cheers Ian.


... Electrolux Vacuums

I have FILTER QUEEN vac that a friend gave me because he unhooked the 5 wires coming from the motor and he didn't know where they when could I get photo of the wires coming from the motor and whe


I would go through the manufacturer for the diagram. ... Filter Queen Cheetah II Ash - MU305 Bagless Canister Vacuum

I replaced the motor in my Oreck vacuum and it runs much faster than it used to and is very noisy. The wiring diagram that I received with the motor was very hard to read so I don't know if I wired it correctly. I also was not able to hook up the dual head lamps. Thanks, Bob


Hello Bbrote,Please visit the link provided below and find your model and then click for schematic :http://www.hescoinc.com/vacuum_cleaner_parts/oreck.html ... Vacuums

Motor Fried? Eureka 431BX Vacuuming, and then all of the sudden the motor just stopped. Well idk if it's called the motor; the beater bar still spun, it was just the fan that stopped spinning Here is the whole vacuum in pieces http://i28.photobucket.com/albums/c237/SirFafner/Vacuum001.jpg Bottom Part, beater bar already taken out [Functions Fine] http://i28.photobucket.com/albums/c237/SirFafner/Vacuum002.jpg White Wire connecting to the fan motor [Looks black, i think it's fried, and that's the


Funny you said that,I went today and bought a bissel at Wal-Mart.Sure hope it lasts longer then the Eureka did.I will probably try to take the other one back to the store if I can find the receipt.Thanks so much. ... Eureka 431BX Bagless Upright Vacuum

I just got this euro pro shark steam mop. I dont have a manual for it so i dont know much about it. I put water in it and it heats up but when you start to use it. It makes a gurgling kind of sound and steam comes out, but not very much i dont think and on the floor you can't hardly tell where you went over the floor at cuz it's not very wet at all. So is it suppose to make a gurgling sound and should'nt the floor be alittle wetter?


Call Shark. They have good cust. support. ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Motor still runs--sounds like jet engine. do I need a new motor? or is there some sort of muffler that has malfunctioned? vacuum belongs to disabled mom---so trying to do work ourselves--cant afford much. dont see anything obviously wrong--but know nothing about electric motors.


This little vac I think is actually made by Samsung. If it is ROARING and vibrating, either the bearings or suction fan is in bad shape. Remove the lid as if to inspect the belt and see if there is a visible intake opening with a plastic fan rotatin ... Bissell 3590 CleanView Bagless Upright Vacuum

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?


Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum

Model # 5770 the brush motor runs and shuts down after a few seconds...Turn unit off and the brush again will run for a second or two...If I don't turn unit off brush will not start up..Could it be the printed board..the motor brushes..or the wiring that goes from the printed board to the main motor...Thank you


Seems like your unit goes into failsafe because it detects something wrong. Well you should check the brushes and replace them if they are worn out. Also check the wiring for shorts etc, becaue the unit maybe tripping due to an overload. The printed ... Bissell Vacuums

We have a dyson dc 07 animal the machine was working fine then switched off after returning to the machine minutes later it wouldnt switch on, i removed on off switch cover and used a short piece of wire across the brown wires flicked the wall switch and it worked, aha i thought faulty switch aquired a new one to no avail and now even the short piece of wire trick doesnt work, has the motor died do you think, it wasnt over heating or making strange noises prior to refusing to work


It could be the motor. I'm having to replace the brushes on my DC 05. It appears that you can only get brushes for the YDK motors in the DYSON, not the Panasonic motor. Which might be saying something about the YDK motors. What happens is that the ca ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

I am putting my bissel 8910 back together and behind the motor there is a black 3-way tubing connector. One side goes to the pump discharge, one side goes to a tubing going to the right rear wheel (facing the unit from the front) I don't know where the third side goes to. I do not seem to have another tubing for this one to go to? Maybe it is lost or ?


Hi, its hard to know what its for without seeing it. The best way to test this is to start the machine and vacuum a part of the carpet/ floor. Then let me know wht the vacuum is not doing. This will narrow it down. Please, get back to me. This sounds ... Bissell 8910 ProHeat Clear View Upright Vacuum

Wires pulled out of the plug and I don't know which one goes wher


You might need to buy a new plug, try this sitehttp://www.onlinevacuumparts.com/ps-328-7-ge-6850-106766-canister-power-nozzle-parts.aspx ... GE 106766 Bagged Canister Vacuum

Can't find info for hoover steam vac spin scrub model # F5905900 on Hoover website, doesn't show that model number at all...looking for mesh (kind of cone/cylinder shape) that goes in dirty water tank (I think) and also the tool (wand) that slides into front to clean it out. It doesn't pull all the water up very well and the filter has been missing for some time. I don't know if that has anything to do with it or not. As far as the wand tool goes, I have taken the cover off at this point and


The cleanout tool is part # 43514001. The filter is # 90001398. Be sure to leave a 1/2 inch gap between the top of the filter and the bottom of the lid. If you need a manual, try model F5914-900 0r F5912-900 on Hoover.com ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

How do you wire a 2 speed fq motor. I know the blue/blue. the red/red. The yellow /yellow and I believe the whites together with the grey of the pn outlet. Does the black from the motor the black from the cord and the other grey from the pn outlet connect together ?


I have not seen the new two speed but sounds like the wiring is coded to teh switch by colorOn a single speed it would be this way.\015\012\015\012Power cord to side 1 of switch.\015\012Switch to motor 1 and PN receptacle 1, etc ... Filter Queen Cheetah II Ash - MU305 Bagless Canister Vacuum

I completely took my Bissell 7901 steam heat apart to clean out the hose and i dont remember how it goes back.i dont need the manual it has nothing i need in it


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Lindhaus 031207 blue wire from motor pulled out from terminal block - need wiring diagram to tell where it goes back into the terminal block


I am sorry that this happened. It appears the unit is proprietary and you can download most of the information that you seek from:\015\012http://www.lindhaususa.com/support. ... Lindhaus HEPA 14 HealthCare Pro Bagged Upright Vacuum

Our Vax 2000 motor goes OK but it is starting to smell of burning and making a grinding noise. I haev taken the motor unit off and the sponge filter but still it persists. What is the probelm and the repair please


... VAX Appliances 2000 Canister Vacuum

Hvr motor -four way switch ,two white ,and blue and brown wires -what goes where


Try this linkhttp://www.youtube.com/watch?v=97ZNEjKtu-gor this link one mite help you ... Henry Numatic "" Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0587 seconds