Having problems with your Vacuums ?

Kenmore progressive power head replacement

\015 The wheels are broken off the powerhead. What are our options?\015

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kenmore progressive power head replacement

... Vacuums

I have a Kenmore Progressive model 116.22812204 purchased 2003. The swivel (part nuumber 8195133) that attaches the extension wand to the power mate attachment snapped, so I can't keep the parts connected. I can order a replacement part on-line, but I don't know how to replace it - is it difficult to take apart the power-mate and replace this part? Do you have instructions on how to do it? Thanks!

... Kenmore Vacuums

No power to head of Kenmore Progressive canister vac

... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

No power to head of Kenmore Progressive canister vac

... Vacuums

No power to head of Kenmore Progressive canister vac

The extension wands are defective and have trouble with their plug connectors on each end. The power head has a reset button on top right but no lights mean no power which means the wand isn't connecting the power to anything. Sears has ... Kenmore 22812 Bagged Canister Vacuum

Replacing Power Cord Kenmore Progressive Upright

That actually sounds correct, if it's the model I'm thinking of. As long as you're talking about connecting to the wires that are held in by the wire nuts you should be good to go. \015\012\015\012-R ... Kenmore 23613 Progressive PowerMate Bagged Canister Vacuum

Unbeknownst to me, someone took the bag out of my Kenmore Progressive vacuum and failed to replace it. I have been vacuuming without a bag for months, and today the vacuum stopped sucking. When I opened up the front to replace the bag, tons of dirt and dust came pouring out. I thoroughly cleaned the vacuum, put in a new bag, but still no sucking power. Just dust coming from the rear vents where one of the filters is. Is the vacuum ruined, or is it a simple solution of buying a new filter?

Sounds like you need to buy a new motor. All that grit and dust will ruin a motor and I'm surprised it lasted as long as it did.\015\012This is where a vacuum that won't run without a bag would have been nice. (Aerus for one) ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

How do you replace Kenmore progressive power cord?

... Kenmore 25512/ 25513 Progressive Canister Vacuum

Replace kenmore progressive vacuum power cord on model 11622612205

... Kenmore Vacuums

The vaccum cuts out replaced the wand but still having the same issue - the powermate head is fine and does not appear to be causing the problem. I have two Kenmore Progressive Canister Vacuum and this is happening on BOTH

... Kenmore 25512/ 25513 Progressive Canister Vacuum

My kenmore progressive canister vacuum's power head has stopped working. When I check for suction from the hose, it seems strong. Could it be a belt has broken? Is this a repair that I could do myself? Thank you!

... Kenmore Vacuums

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v

Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

My kenmore progressive caniser needs a new power cord. the plug had one of the metal prongs break on the plug. how can I replace the cord? model 22812201

I do not know if you want to replace the replace the power\012cord or the receptacle for the power wand?\012\012If you need the prong for the power cord you can purchase a\012replacement power plug from a local hardware store and it will functi ... Kenmore 25512/ 25513 Progressive Canister Vacuum

The motor on my Epic 6500 works, the hose is sucking, but the power head isn;t working... I tried the sidestep power head and that one works. Ive opened and replaced the belt and that is fine. The bulb was already burned out and wasn't replaced so I cant tell if theres power to the head. What else could it be?

Connect the power nozzle directly to the hose and try.\015\012Check the terminals where the wand connects to the PN. If any are discolored or cracked, that may be the problem.\015\012Open the PN and check for loose or broken wires and co ... Electrolux Epic 6500 Vacuum

Power head for Kenmore Canister Vac

Another potential problem for the increase in difficulty in turning the beater bar (drum) could stem from extremely dirty bearings, located at each end of the beater bar. I've seen hair knotted up to the point it chokes the bar and significantly redu ... Kenmore Whispertone 29512 Vacuum

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin

... Vacuums

I Have two questions concerning my AIRVAC AV2500 Red Series Vacuum System. How do you replace the light in the floor power head sweeper and can you replace the permanent fabric filter? We had the system installed in 2004 and the light in the sweeper head just went out and can not find any manual on line on how to replace it. The filter if not torn but avter 6 years it probably needs some kine of cleaning or replaced even though it says permanent. Any help would be appreciated. Jim McCluskey

... Vacuums

I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos

It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum

Hi, I have a canister Kenmore vacuum with power head. Everytime I use it, it smells sour. Its strong and like FEET with bad odor. My old Kenmore did the same thing but I used it anyway...because the power was great. We don't have feet problems or pets. The carpeting was new when we bought this vacuum.

Moisture/humidity mixed with organic dust (like sloughed skin cells) can cause the smell you describe in vacuums. I recommend that you purchase scented granules that are placed inside of the vacuum bag. Do not buy Carpet Fresh because the fine powd ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

The power head of my DC 21 keeps cutting off as soon as I start moving the hose around. The only way to get it going again is to step on the main switch on the canister, then the whole cycle of off and on starts again. I have replaced the entire power head and tested the continuity of all the wires in the hose and they are good. The repair shop says the PCB is bad but can not get one. What can I do ?

Not much. my only suggestion is to dig through the internet and try and find that pcb it may take awhile but it would be worth a shot. if you dont think you can make the repair take it to repair shop with new pcb and let them do it. ... Dyson Genuine DC-21 "Stowaway" Spare HEPA Filter, Dyson

The power head keeps shorting out during use. one of the connecting prongs from the handle to the power head is black instead of silver and is smaller in diameter like it has been arcing inside the connection. could this be the problem and if so can I replace it or will I have to take it to a repair facility. Thank you for your help, Jim Carey [email protected]

This is a problem with the connection in the wands and the powerhead. Because they are shorting out you may have to replace the neck on the power nozzle. (Leave that to a pro). But you will definatly have to purchase a new wand as replacement wires a ... Electrolux Lux 7000 Bagged Canister Vacuum

The power head on my kenmore 22822 Canister Vacuum won't work? the power upholstery head works fine.

I have the kenmore whisper belt and i have a reset button on mine ... Kenmore 22822 Canister Vacuum

The carpet head on my Kenmore vacuum has stopped working. It is a Kenmore progressive vacuum with a whisper belt head.

... Kenmore 23313 Whispertone Bagged Canister Vacuum

Power cord can not find replacement power cord for power brush attachment on kenmore canister vacuum, model #2491290 power brush attachment model # 5491290. i can not even find those model #'s anywhere online, not even partsdirect.com. any help would be great. thanks, david

Call 1-800-948-1358 ask for Buck mon.-fri. 9am-5pm est sat.9am-1pm est ... Vacuums

Chang the belt in my kenmore power mate power head

... Kenmore 25512/ 25513 Progressive Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0720 seconds