Having problems with your Vacuums ?

Vax 1900w hoover

\015 My wifes vax hoover has developed a problem.When swithced on the motor gets faster and faster to the point i have to switch it off as it sounds like its gonna explode, its not sucking up either, any ideas??? thanks\015

Answers :

Take the motor out and check the fan, outside of that, you may have to replace the motor.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Vax 1900w hoover

Take the motor out and check the fan, outside of that, you may have to replace the motor. ... Vacuums

Vax hoover my vax hoover keeps overheating and cutting out.

... Vacuums

Hi The band snapped the other day on my Vax Swift Turbo upright hoover and i got a new band from a Hoover repair centre. (Im assuming the bloke sold me the correct band). Was tight to go on. And it seemed ok. However, after switching on the band snapped immediately. Kinda burnt as well (at the point it snapped). Any ideas as to what the problem is here? The hoover is roughly 2 years old and used around 3 times per week. thanks Mike

Sounds like the brush roll is bad. Did you check the ends to make sure they turn freely? If not, replace it. ... Vacuums

Bottom part of hoover wont **** - VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

My vax power 8, 2200 watts 300 air watts 4L capacity upright Hoover is brand new, I emptied out the dust/dirt collecter and cleaned the motor filter yesterday for the first time, i switched it on and all fine, the brush is spinning and the hose is sucking, put the Hoover to work it's fine for about 30 seconds then then suction stops and its dead it won't collect no more, so switched off taken apart again and the motor filter is blocked and full of dust, so I unblocked it, do the same process aga

I had the same problem. It looks like the seal on the lid on the bottom of the cylinder has fallen out when it was emptied. There is no longer a proper vacuum being created so you don't get the cyclone effect and the dirt doesn't collect where its su ... Vacuums


I have one of these too and it used to keep cutting out, replaced the filters and now it wont even turn on.  changed fuses everything, and now im stuck with a dirty house.... ... Vacuums

Hoover 1900w keeps cutting out - Hoover Vacuums

Opened it up little senser near the moter on a wire moved away from the motor dont cut out anymore ... Hoover Vacuums

Fix hoover smart 1900w - Hoover Vacuums

... Hoover Vacuums

Vax 2300 vax v-2300 brush is not turning so changed belt snapped as soon as i put hoover on and getting burning smell put another belt on same again and brushes still not moving only 4 months old

If the roller brush cannot be rotated easily by hand, it is likely that debris is jammed inside the end caps.Make note of the direction arrows on the end caps as you remove the roller brush. You will need to know this for reinstallation. The end caps ... Vacuums

Change the cable on a vax power 4 hoover - VAX Appliances Vacuums

... VAX Appliances Vacuums

I have a vax power 6 hoover, this was bought in January this year replacing the previous 2 I had bought in 2012. I get the same problem each time in that the hoover cuts out after using it for 5 minutes and I cannot use it again for another half an hour. WHAT IS THE PROBLEM WITH IT?

... Vacuums

The upright VAX hoover model X-005 The manual

... Vacuums

I want to change my belt of my vax power2 u90p2 hoover as ive lost my manual

... VAX Appliances Vacuums

I have a 1850 vax hoover,which does not ****

Have you tried www.part-smart.co.uk they are the cheapest iv found and all genuine parts as well. ... Vacuums


The 121 should only have the main filter ring taken out before the reservoir tank is put in which easily just falls into the main dust tank area. Make sure though that the bin's square edge is at the front where it rests at the front of the Vax where ... Vacuums

Vax upright hoover

... Vacuums

I have a vax swift Hoover burning smell coming out of the bottom

... Vacuums

Just tried to fit a new belt to a vax quicklite 2 upright hoover and the belt snapped is there a right way to fit belt

... VAX Appliances Vax X3 Bagless Upright Vacuum

Vax hoover bagless, there is a burning smell coming from it

Most common burning smell is the belt in the power nozzle. check & replace. ... Hoover S3639 WindTunnel Bagged Canister Vacuum

How to use a vax spring carpet washer ? - Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

How do you I get the base of my hoover off to replace the belt - Vax U91-PF-B-T?

... Hoover Vacuums

Hiya i need to rewire my vax power4pet hoover how do i get to the cable?

... Hoover Vacuums

Can t remove base from hoover to change belt. vax upright

... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

Vax hoover, it has sucked up a piece of cellophane and stopped working have changed fuse but still nothing anything else we can do

There may be a thermostat at the motor, it is supposed to protect the motor if it gets overheated. It may have opened up and it will have to be replaced if this is the case. You also need to remove the clog if you haven't already done so. ... Vacuums

Hoover will not stay on unless i hold finger on switch,have cleaned filters etc still don't work it's a vax 6151 sx,thanks

You have a bad switch on it. You can maybe find the same kind of switch in an electronic parts store. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0590 seconds