Having problems with your Vacuums ?

How do I take the on/off switch out to repair broken wire


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I take the on/off switch out to repair broken wire


... Vacuums

Mrs Cleaner flex has pulled out how do I replace Electric supply wire to switch on handle has broken at switch. How do you remove switch to repair? tonysimmons


Hi\015\012\015\012\015\012\015\012\015\012\015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson DC04 vac.cleaner how do I access the on/off switch casing to repair a broken wire


... Vacuums

How to dismantle twin clean powerhead to repair broken wires? the wires to the pc board have broken but can't seem to be able to remove plastic cover over wires without breaking cover.


... Electrolux Twin Clean Bagless Canister Vacuum

My Electrolux Epic 6500 SR will not turn off by pressing on the switch button. I took it apart and removed the switch assy. I can maunually turn it off & on by pressing the rocker arm on the switch assy. It appears that the problem is with the big blue operator button, not the switch assy itself. The button does not seem to press down enough to cause the rocker arm to switch. The button has a "U" shaped wire that presses on the rocker arm and it may have some broken plastic details at the b


WOW !!! Finally You are dead on, absolutely 100%.... good work!!!.Get only a genuine new switch button with spring from an AERUS Electrolux dealer and reinstall. Then carefully reassemble the entire body and wiring harness.Con ... Electrolux Epic 6500 Vacuum

I want to remove the power switch on a dc04 to repair a broken wore, how do i remove the switch?


Go to www.dysonmedic.com then scroll to the bottom of the page and click on DC04 cable change. You won't get better advice anywhere (and I've got no connection with dysonmedic). ... Vacuums

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?


Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum

My dyson slim vacuum doesn't switch from hose to floor mode. I thought the foot lever was broken. I realigned it but it doesn't switch now from floor mode to hose mode. I take out the hose and I can see the white part. I thought it should move as you go from upright to recline position of the handle.


The changeover valve is not activating - call the Dyson helpline - they'll set you up for a repair with a repair dealer in your area. ... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

Eureka 4870GZ vacuum: carpet/bare floor switch does not work, so now roller won't spin. can i repair this myself or do i need to take it in? if i need to take it in, what's the cost?


... Eureka Smartvac 4870 Bagged Upright Vacuum

Hello, I have a Hoover 3200 Turbo Power vaccum. while the motor appears to be working fine the vaccum no longer picks up the dirt. I turned the vaccum upside down and the belt appears to be broken. would a broken belt stop the pick up, there appears to be no suction. This vaccum is approximately 10 years old. is it worth fixing? I live in Virginia Beach Va, where would I take the vaccum for repair? my zip code is 23456- Thanks Cleta Goode


... Hoover Vacuums

Eureka Boss 4D (5892BVZ) - Switch Replacement & Fried Wires


If you got the handle apart, Id say you can probably fix it yourself. You might be able to patch it but I would say to maximize your effortrs please visit RepairClinic.com to find the exact replacement parts you need. They also have expert advice ... Vacuums

Oreck Upright Hi Redev, I'm not sure what model I have (about 6 years old...upright, looks like the one in the picture). I changed the belt (which was torn) and then the next time I used it, it cut off on me. Now if won't turn on at all. (I turn the switch on and off and nothing happens as if it is not plugged in but it is!). I noticed at the top where the power cord enters the handle, it is all frayed. Could the electrical wires have detached? Anything you think I should check before taking it


The cord could be bad and will ahve to be replaced. It would have to have a problem inside the handle or down by the motor. ... Oreck XL2600 Vacuum

Dyson DC23 Vacuum shut off and came on. Thought it was a problem at the electrical outlet as when moving plug it would come on again. Seen canister was full, emptied it and cyclone was quite plugged up so poked out the dirt. Had dog hairs in it as well as some ashes I had just vacuumed. Plugged unit in again and pressed switch. Will not come on. Tried another outlet. Is there a reset button somewhere or could the ashes have seized the motor. What can I try besides taking it to a repair sho


... Dyson DC23 Bagless Canister Cyclonic Vacuum

Broken switch and need to know how to take apart the fein tool


... Fein Multimaster Rs - Msxe 636 - 2 Rs

My grundig yacht boy 400 has a broken antenna and I would like to repair it. It came off , has small screw still attached at bottom. Need to take apart radio and don't see how. Thank you, Lourdes


... Vacuums

The power head of my DC 21 keeps cutting off as soon as I start moving the hose around. The only way to get it going again is to step on the main switch on the canister, then the whole cycle of off and on starts again. I have replaced the entire power head and tested the continuity of all the wires in the hose and they are good. The repair shop says the PCB is bad but can not get one. What can I do ?


Not much. my only suggestion is to dig through the internet and try and find that pcb it may take awhile but it would be worth a shot. if you dont think you can make the repair take it to repair shop with new pcb and let them do it. ... Dyson Genuine DC-21 "Stowaway" Spare HEPA Filter, Dyson

Water Leakage We have a Bissell Proheat (Pro Tech). I don't think it is the 2X model. When releasing the water with the knob on the handle, water comes out the side of the housing at the lower part of the unit. Is their a seal that my be worn out or broken. Can you give us some ideas before we take it to an expensive repair man to fix


Check the water bottle. Ours has been doing the same but putting a bit of j cloth between what they call the o ring and the cap fixed it. Really you need a new bottle assembly ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

My Fein won't turn on without rapping it on the floor ! I turn the switch on and it won't run until I tap or rap it and will shut off during operation. I'm sure there's something loose , but should I attempt it or take it back for repairs . Last time I tried it , it woudn't turn on at all . My wife purchased it earlier this year from a TV infomercial .


ELECTRIC FIELD (and all the push contacts are most of the time the problem the cause by this machines , dirt in the switch (the switch is made to disassemble to clean it sometimes .little screwdriver neccesary . ... Fein Multimaster Rs - Msxe 636 - 2 Rs

Hi, I have a Sebo X4 which is almost 3 years old. I haven't had any problems with it until the last couple of days when I notice a slight screeching noise when in upright position, coming from the roller mechanism area. If I slightly push the sebo forwards it gets worse, if I tip it back it stops. If I take the roller out and switch on, there is no noise. I have always been careful not to tip the machine forwards when using the hose, but I recently lent it to a friend whose hoover had broken do


I dismantled the top part of the machine from the bottom and there stuck right down in the bowels of the tubes was a piece of card, a dress label! somehow it was only making a noise when the machine was in an upright position. It took a bit of stretc ... Sebo X4 Bagged Upright Vacuum

Power Nozzle Model No. N137A (for Electrolux Epic Serial 6500 SR) has a broken wire. Can I get a replacement power nozzle or find a repair place in the Everett, Washington vicinity?


... Electrolux Epic 6500 Vacuum

Simplicity vacuum My vacuum just cut off and now it wont start. I pressed there restart button but nothing happens I have 2 fairly old Industrial hitachi dry vacuum in my workshop both 110v and both wont start. Both i was told were manufactured in Italy and both have a manual and auto switch. It has a black top, takes an orange paper filter inside and its bin is dark blue. Sorry i've forgotton the model number. I've inspected the wiring but it's fine, could it be the motor and how do i gain acc


Just take it in to your vacuum store. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

We have a dyson dc 07 animal the machine was working fine then switched off after returning to the machine minutes later it wouldnt switch on, i removed on off switch cover and used a short piece of wire across the brown wires flicked the wall switch and it worked, aha i thought faulty switch aquired a new one to no avail and now even the short piece of wire trick doesnt work, has the motor died do you think, it wasnt over heating or making strange noises prior to refusing to work


It could be the motor. I'm having to replace the brushes on my DC 05. It appears that you can only get brushes for the YDK motors in the DYSON, not the Panasonic motor. Which might be saying something about the YDK motors. What happens is that the ca ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Hello! I have a Rainbow vacuum Model# D4C that needs a switch. I am only able to get the new style 4 wire switch and it has the 6 wire. Can I make the 4 wire switch work in place of the 6 wire?


... Vacuums

My Dyson DC 24's beater bar switch didn't actuate and the beater bar didn't turn. When I brought it to a certified serviceman he told me that a wire interferred with the switch and all he had to do was move the wire out of the way of the switch. At the time the machine was under warrantee and it didn't cost me anything. Now however, the machine is out of warrantee and the problem has returned. Does anyone know how to access the switch and move the wire out of the way?


Hi- I had the same experience but it turns out there's a small trip switch if you've taken the brush out to clean it, it needs to be reactivated by pressing the small red button to the right of the brush... took me a year to figure this out! Been mea ... Dyson Ball DC24 Bagless Upright Vacuum

Replaced Oreck power switch. 2 black leads and 1 white lead for switch. Posts marked 1, 2, and 3. 2 black wires to switch powers on. Connect white wire and breaker trips. Where does the white wire go?


Both black go to the switch. Power in - black to switch / white to white from motor. From motor - black to switch / white to white from power cord The black wire from the power hooks to ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0494 seconds