Having problems with your Vacuums ?

1957 Sunbeam Twin-Blade electric lawn mower shaft bushing

\015 I have a late 50's series Sunbeam twin-blade electric lawn mower that I use regularly. The shaft bushing(s) on the left blade has worn out, and there's too much play for me to run it w/o ruining the machine.It appears that the belt-run cog inside the housing is the part that is supposed to come off of the shaft to get to the bushings, but instead of a cotter pin or other fastener holding the cog in place, it looks like a rolled metal pin that may have been pressed in place.How do I replace the shaft bushings so I can keep using this great vintage appliance!? I found a website that supplies parts for this model year, but no schematics or user manuals.Thanks!\015

Answers :

Mower Man,

Have you fixed your problem yet? I recently acquired the twin blade/twin chute mower with the same problem. You have to tap the roll pin out with a hammer & punch. A bit of a problem since you have to remove the motor first. Very easy to work on though, only 4 screws to take out for that. If you have any other questions/problems you can contact me via email @ [email protected]

Good luck,

Doug
Http://abtecparts.com/Sunbeam_twin_blade_single_chute.htm


they have parts.
belt, bushings, blades
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

1957 Sunbeam Twin-Blade electric lawn mower shaft bushing


Mower Man,Have you fixed your problem yet? I recently acquired the twin blade/twin chute mower with the same problem. You have to tap the roll pin out with a hammer & punch. A bit of a problem since you have to remove the motor fir ... Vacuums

Lawnmower I have a black and decker hovermaster lawn mower. While mowing my lawn I went over a small stone. It doesn't seem to have damaged the blade but the engine instantly cut out and I am unable to start it again, I have replaced the fuse which has made no difference, Can you suggest anything please.


There may be a thermal fuse fitted to the motor, sometimes they reset when they cool down. Sometimes they are a one shot fuse, when they blow the have to be replaced.There may also be a reset switch on or inside the operating lever/switch. ... Vacuums

There is a shaft that comes out of the pump of my Bissell 1623-1 Power Steamer with gears on it. The belt to the brush attaches to it. When I went to change the belt, the belt was fine but the gear itself with the small shaft on it was no longer attached and just dropped out. It looks like there might have been a bushing there, but no more. Any ideas?


... Bissell Vacuums

I have a Sunbeam Electric Blanket model BL07050 and plugged it back in after washing. Both controls now have the active light flashing green. Does this mean both controls are faulty or the blanket is faulty. Sunbeam sent instructions but this did not help - can you suggest anything please


... Sunbeam Vacuums

I have a Philips PT725 electric shaver. I want to buy new blades and blade grids for my shaver. I am in Centurion in South Africa


... Vacuums

Need a bushing for motor shaft and new brush


... Bissell 2050 QuickSteamer Upright Vacuum

Just bought a CCR23DAB Bush Radio. Can't get the damn thing to power up. Electricity is getting to it as a counter display can be seen. But the snooze/power button doesn't fire it up nor any other button. Going to take it back I guess


... Vacuums

I am looking for replacement cutter blades for the Rival Stripper Electric Fruit and Vegetable Peeler. Do you know of a source for these parts?


You can approach the appliances dealerships to get addons or spares for the cutter . \012If the Rival dealer is available you can get the spares or contact in the official site :\012\012\012 ... Vacuums

How do I find the model number on my sunbeam mixer? I need new mixing blades


Some Sunbeam Mixers don't have a model number stamped on them. However, the service number located on the mixer functions basically as a model number when it comes to replacing parts. Hope this helps. ... Vacuums

I have the honda hrx 217 self propelled lawn mower but the self propepl does not work. the cable is all hooked up right its never been touched. one day it just stopped working please help me


... Vacuums

F2 Flashes on our Sunbeam Electric Blanket No.V70-CC75 Style 085


... Vacuums

Need a schematic for Sunbeam electric blanket with G85 controller.


Hi, the schematics for the electric blanket are not readily available online maybe due to the company's policy just like some others that i know. You may try your luck by contacting Sunbeam on (800) 667-8623 to make a request for the schematics ... Vacuums

I need to replace the fan blades on a Kirby Heritage II, Model 2HD, vacuum cleaner. How do I remove the drive shaft that the fan is mounted on? Thanks, Robert Croft


... Vacuums

I have a Sleepwell Dreamland Luxury cotton Electric Duvet. It has twin heater controls, the control has a 1 to 9 heat setting and also a time duration function. One of the controlers works fine but the other turns itself off after about half an hour. Can you help and perhaps give me an address where I might purchase a new heat control.


... Vacuums

A lawn mower black hawk


I have got a little yell o steam cleaner it is getting up to pressure but there is no steam coming out of the nozzle how am I able to fix this can some one help me with this matter please ... Vacuums

Impeller installation i took the whole vacuum cleaner apart to replace the impeller . i did not take note of the way the bushings need to be put on the shaft . do you know of a diagram out there that shows how to do this.


Here is my online guide to changing the fan. Hope it helps...\015\012\015\012http://reviews.e ... Kirby G4 Bagged Upright Vacuum

Have Sunbeam Electric Blanket Model BL442D, Only 6 weeks Old. Has Started to flash with An E message on the control. Can anyone help me please.


... Vacuums

We have an sunbeam electric blanket model BL 0750 We dont seem to be able to programme it to heat up. Control lights are flashing


Hi. If you have a double or queen size blanket, switch the controls from one side to the other. If the fault follows the control, then the control is faulty. If the fault stays on the same side of the bed, then the blanket may be faulty. Most recent ... Vacuums

Looking for a 8HP Snapper Comet SAE J607 operator manual. Where can I find? Riding lawn mower


... Vacuums

The top blades of the dasher of my Rival 4-quart electric ice cream maker (model #8704) are broken. I need to replace this part. I couldn't find this model on the website or any site from which I could order this part. Can you help me?


Hello,The part for your ice cream maker is not available any where online. The best thing you can do is to contact the manufacturer and ask them where you can get the part. They might have dealers who sell the parts.You can ca ... Vacuums

Hi, we have a Sunbeam electric blanket model no. BLO750 and type 696. It's a double blanket with dual control that can be used for different settings on either side. Both sides have been working ok but last night one side wouldn't heat and the green light kept flashing and now, whatever we do the green light keeps flashing except, when we set the control to "off". We can't find our Owners Manual to see what we are doing wrong, can you help please...or can you advise us where we may be ab


... Sunbeam Vacuums

How do I replace part # 941-0656A in my troy bilt riding lawn mower?


... Vacuums

I have a powerbase 1050W mitre saw and am trying to cahnge the blade. There seems to be no way of reoving the blade, How do you remove the blade? Ther eis a guard over the blade which stops the blade coming out when not in use, and when you lower the blade to cut, which pull sback the guard, you cannot remove the blade as he blade is touching the base. I have tried to find a copy of the manual on line but cannot.


... Vacuums

Rainbow 2e Overheats... its the Electric Motor cooler fan......


It is pressed on, that is why you have a splined shaft. If you use a socket or nut driver, you can knock it ino place with a hammer. But don't hit too hard. you don't want to damage the end. ... Vacuums

I have a sunbeam stickmaster pro SM8640. The


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0423 seconds