Having problems with your Vacuums ?

Dismantling a Dyson DC01 motor - Vacuums

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dismantling a Dyson DC01 motor - Vacuums

... Vacuums

I have a dyson animal dc17 vacuum and it totally died. Now I can't figure out which wires go where when I install my new motor. (motor #: 160906G) Do you happen to know where the various color wires go or a place I can see a diagram of the motor with wires attached? I should have taken a photo of it before tearing out the old motor. I don't know where to connect the three coming out from the upright portion of the machine and the red seems to go to a switch (?) and there is a black (connected t

... Vacuums

DYson DC07 not sucking properly when in upright mode. I have tried cleaning out pipes etc and even tried an old motor section I had in garage (replaced once under warranty as kept cutting out and they left old motor section here). Even the old motor section had same prob so this suggests its something in the rest of the vacuum cleaner (whats left after you have lifted off the green motor section and dust collection area if you see what I mean? Any advice weclome please.

Blocked filters ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Motorized brush bar not turning on Dyson Vacuum

Apparent common failure is that either the thin yellow and or blue motor drive wires that run from the LH side of the vacuum where the "control board" is located down into the hinge / ball area become stretched and then fray and eventually break. Ha ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

How to dismantle a dyson turbine head - Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Dyson DC31 motor surging and no suction - Dyson Vacuums

... Dyson Vacuums

Can I buy a motor set part for dyson dc35 - Dyson DC35 Handheld Vacuum

Try this link belowhttp://www.vacpartswarehouse.com/Dyson-DC35-Handheld-s/3899.htm?searching=Y& ... Dyson DC35 Handheld Vacuum

I have a dyson canniter stow away vacuum. i've had it for 2 years and it just started having a problem. when i turn it on the motor starts just fine but the vacuum head does not turn on. Yet when i push it forward it trys to start and turns on for a second and turn off - almost like the connector isn't connecting the hose to the head very well anymore.

Hi, After reading you're problem, the symptom's are just like you said. Its just a matter of checking the connections. The connection where it plugs into the head it self. When you push forward the forward motion and down pressure makes ... Dyson "Stowaway" Canister Vacuum Vacuum

Dyson DC01 will not lock in upright position - Dyson DC07 Bagless Upright Cyclonic Vacuum

... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson dc01 Repair manual - Dyson Vacuums

... Dyson Vacuums

Dyson DC23 Vacuum shut off and came on. Thought it was a problem at the electrical outlet as when moving plug it would come on again. Seen canister was full, emptied it and cyclone was quite plugged up so poked out the dirt. Had dog hairs in it as well as some ashes I had just vacuumed. Plugged unit in again and pressed switch. Will not come on. Tried another outlet. Is there a reset button somewhere or could the ashes have seized the motor. What can I try besides taking it to a repair sho

... Dyson DC23 Bagless Canister Cyclonic Vacuum

How to replace brush bar motor on dyson dc15 - Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?

Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I'm trying to figure out which dyson vacuum is better, the DC14 or DC17. from what i read, the DC17 is the newer model of the DC14, the DC17 added an extra motor for the brush, but from the dyson site, the DC17 has less suction power. it went from 250AW (dc14) to 220AW (dc17). is that a significant difference that i should be worried about?

Hi,DC17 is much better than DC14. I always believe User's review are much better than what Features Company usually Displays.Read :-http://www.epinions.com/review/Dyson_DC17_Animal_Vacuum/content_404790546052 ... Vacuums

My dyson dc01 fan belt keeps breaking - Dyson DC07 Bagless Upright Cyclonic Vacuum

Ok 1st check that the roller is free to move otherwise it will stress the belt..next no sharps on roller guide or brush roll to cut into belt..Please leave feedback ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Noisy motor on Dyson Vacuum Cleaner and how long should a motor last Roy

A motor can last a long time or a short time, there is no way to predict how long one will last. Most times it is dust has gotten into the motor bearings and they get nosiey. Replacing the motor is the only cure. ... Vacuums

HOW DO I CHANGE THE MOTOR ON A DYSON UPRIGHT - Dyson DC07 Bagless Upright Cyclonic Vacuum

Go to www.dysonmedic.com then scroll to the bottom of the page and click on DC07 motor replacement. You will find very detailed illustrated guidance. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

How to dismantle a dyson dc07 cyclone - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hi there,We wouldn't recommend attempting to dismantle your Dyson's cyclone assembly as this may cause damage. If you feel your machine isn't working as well as usual, I'd encourage you to get in touch with us directly so we can help - you ca ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson vacuum How to change the motor for a new one? How to seperate the plastic housing? Where to purchase a replacement motor? Thankyou

Hi There, I have posted up a youtube video showing how to do this repair on a dc08. The dc29 is pretty **** close in design in terms of the motor cavity. In terms of where to buy a motor amazon if you are in the US, ... Dyson DC29 Animal Vacuum

Motor loud I have a dyson dc17..recently when i turned it on and pulled the handle down to vacuum the motor was very loud..put the handle in the upright position it is quiet.any suggestions?

When you put the handle down it turns on the brush roll. you may need to clean the brush roll or replce it if the bearings are bad.also clutch and 2 belts are started when putting handle down for brush operation. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson motor burnt out - Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Hi there,I'm sorry to hear you're having difficulties with your DC08. If you haven't already got in touch with us directly, I'd encourage you to do so - you can reach us on 0800 298 0298. Our Helpline is available from 7am until 10pm, so plea ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

How do you replace motor on DC29 Dyson vacuum

... Vacuums

My dyson vacuum cleaner DC01 will not **** when you pull the pipe out of handle and it is not blocked

Replace filers ... Vacuums

Dyson DC07 My DC07 cuts out after 5 mins and I want to replace the thermal cutout. I have cleaned it thoroughly, including the cyclones but it still cuts out. How does the plastic moulding around the motor dismantle? I have started by removing the 4 torx screws but the upper grey housing does not want to detach and I am worried about breaking the plastic. Appreciate any advice.

Try this page: -http://www.fixya.com/support/t192124-overheating_dyson_dc07Regards Gualo ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a dyson root cyclone. i dismantled it to replace the belt, it is not the belt which is on the roller brush, it is the belt which is from the motor, it was easy to take out as it was broken, i will get new one tomorrow now im wondering how do i fit it in.

The belt that fits on the motor is the same belt that drives the roller brush, all you need do to gain access is remove the sole plate, normally attached with 3 quarter turn connectors, use large flat screwdriver to turn them ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0864 seconds