Having problems with your Vacuums ?

How to remove cover on Bush BC-502 hoover

\015 Need to remove the cover to access the motor\015

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to remove cover on Bush BC-502 hoover


... Vacuums

Agitator belt failed in my Hoover F5853-900 Steam Vacuum Cleaner. But can not remove bottom Cover .. have removed top cover and two screws from the bottom Cover. The smaller Cover is glued to the large Bottom Cover. Need help.


Hello,Unscrew the plate. check if there is any screws at the bottom, if none, exact little pressure to pull out the bottom cover. At this \015\012point you should be able to see the broken drive belt along with the two\015\012 drive bars ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac


On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I need to replace the idler arm assembly on a U6439-900 hoover wind tunner upright. I have the clear cover completely removed but still do not see how to remove old and insert new assembly.


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover Alpina 2 1300 cleaner. I need to split the upper and lower casings to check that the switch is working. I have removed the screwa in the area around the bag, but now need to remove the switch and cable rewind covers, as I assume there are more securing screws under them. Can you advise how to do it please?


Move covers (forcibly !) away from the centreline of cleaner then move to rear until released. The covers are held by slide catches on inner edges. ... Vacuums

Hoover self propelled bagged windtunnel upright model #U6435-900...how do you remove the green plastic shell cover to get to the part that secures the v belt...we need to secure the bolt and cannot get the area. Brushes and transmission wheel not rotating? thanks


Greetings from GoVacuum,\015\012\015\012Here's a great video repair tutorial that we've put together to try and help you with the repair on your Hoover WindTunnel. I hope that this helps you with your repair. If you found this solution ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

How do you remove the back cover on the Hoover Steam Vac Dual V floor cleaner?


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

How do you remove cover from hoover freedom


... Hoover Vacuums

How to remove the cover on Hoover U6446-900 to replace the Actuator Arm


... Hoover U6446-900 WindTunnel Bagged Upright Vacuum

Remove cover on kenmore vacum model 116 - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I need to replace the agitator belt on a Hoover Elite U4465-9 upright vacuum cleaner. I have removed the bottom cover, but there is no access to the motor spindle to loop the belt around. How do I do this?


... Vacuums

I have a Hoover Windtunnel Farrington upright model U6431-900 It has worked flawlessly until last week. The roller brush has stopped turning and I believe it is the belt that has broken but I am not sure how to remove the cover to inspect it and replace the belt if that is the problem. Please inform me how to perform the operation and what I should I look for? Is there a site with a diagram on how to replace said parts? Thanks for any and all helpful info that you can supply me with. Larry


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783264\015\012Generic problem for all Vacuums\015\012I have a Hoover WindTunnel\015\012Posted by ... Vacuums

Remove clear plastic cover on hoover steamvac


... Hoover F5906-900 Upright Steam Vacuum

I have a Hoover convertible vacuum cleaner about 30 years old. How do you remove the cover to replace the light bulb?


... Hoover U5255-900 Upright Vacuum

I have a Sears Upright vacuum cleaner, model 116.35922500. The vacuum wasn't picking up. I discovered a clog in the nozzle hose. I attempted to remove the cover of the brush unit to clear the clog. I was unable to remove the cover completely, but was able to clear the clog. My problem now is that I cannot replace the cover correctly. Is there a way to remove this cover? Thanks, Elizabeth


When you tried to remove the cover did you have to put a little force on it to get to the clog ... Vacuums

Flair S2220 Removed the four screws holding bottom cover but still unable to remove cover. Is there something else holding cover? The cover on the srew end will seperate but something appears to be holding cover on beater bar end.


Pop out the two little rollers underneath, at the front. you will find two little screws holding it on. Unfortunately, I found after I broke it off! ... Hoover S2220 Flair Bagless Upright Vacuum

I havea Bissell ProHeat Model 7901. My problem is that the brush doesn't rotate. I have removed the access cover and both belts and found that the central cylinder for both belts is frozen and will not turn easily. Both belts are fine, except they are now burnt from this cylinder not being able to rotate. What I need is how do I remove the top cover to get at this cylinder to remove it and free it up?


... Bissell 8910 ProHeat Clear View Upright Vacuum

Kenmore Model 116 Cannister Vacuum.Trying to get into motor area. Think belt is worn out. I have removed the front two screws under the hinged cover, but can not remove cover over motor.. Still attached at rear. No evidence of any more screws to remove.


Under the cordwinder actuator button, are your other two screws. To remove this cover, take a flat tipped screwdriver and , very carefully, find the "tabs" (there are two) both on the front section under the button. Then, Carefully, press them in a ... Vacuums

Remove bottom of cover on vacuum bottom. Making a


On this model, the bottom does not come off but the top does. on the top hood there are 2 latches to turn with a screwdriver and the hood will come off. ... Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum

Bosch canister vac BSG81313. Took cover off to remove lots of hair, dirt etc from running without bag in place. Everything went back together OK, but cord reel spring went zip when cover was removed. How do I rewind the spring so there is tension when the cord is pulled out ? Wound cord back onto reel, but reel just clicks ever revolution etc...no tension when cord is pulled out of vac. Bob


The spring inside the hub of the cord wheel has escaped from the locking tab. You must completely dismantle the vacuum to access the cord wheel - take it out, reattach the spring and reassemble the unit. All you need is a phillips screwdriver, a pai ... Vacuums

I am trying to disassemble a electrolux 2100. I have looked at instructions given by Chemist 1961 and others. On the side, I have removed the rubber covers over the plastic rails but I can't remove the plastic rails that hold the rubber covers on. If I am right, these rails should just slide right out and the outer casing should come part.....or am I doing something wrong. I have pulled and pulled the rails and they don't budge. The rear end won't pop off. Help!


There's a tab at the back of the rail that needs to be released. Turn the vacuum on it's side, slip the tip of a standard screwdrive into the space between the rail and the back of the vacuum, and tap lightly with a hammer. Tap toward the front of ... Electrolux Lux 5500 Canister Vacuum

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom


Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hoover Vacuum My Hoover cannister model s3614 "runabout powermax" suddenly lost power to the agitator roller in the rug brush. Where the wire cord enters the power brush, the covering has rubbed off exposing the wires which are not bare but still have their own covering. For a while the power came and went as I manipulated the wires but finally died. Is this something I can fix myself or is it going to be an expensive professional repair? (Warrantee has elapsed.) Thanks.


Our Hoover upright vacuum cleaner makes a very loud noise when it is running. What causes this? ... Hoover S3614 Vacuum

How do I remove a motor from a Dyson DC04? The bottom plastic cover can be removed by unsrewing the tork screws but the cover beneath the filter won't come off


I can't say exactly how to do this, but when you can't find the screws to take something apart, they are usually hidden by something else. You did good looking under the bottom cover, but what you're looking for is elsewhere. If there is a seam or ... Vacuums

U6446-900 the drive cable came off and I need to remove the top cover so I can reattach the cable but I can figure out how to remove the cover


From the underside:\015\0121. remove 4 screws holding agitator cover in place\015\0122. remove 2 screws (black screws) holding hose retainer in place, pull hose out through top\015\0123. remove three screws, 2 long, 1 short holding top cover: short ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0761 seconds