Having problems with your Vacuums ?

Dyson wand won't retract


Answers :

Hi there,

I'm sorry to hear you're having difficulties with your Dyson's wand. Without knowing which model of Dyson you own, I'm unable to provide specific instructions. However, if you visit http://www.dyson.com and click 'Support', you should be able to identify your machine from the list. Our online Support guides should assist you in resolving this issue.

Alternatively, if you'd prefer to speak to one of our advisors, please give our Helpline a call on 0800 298 0298 (UK), or 1-866-693-9766 (US).

I hope this helps.

Best wishes,

Jack
Dyson Online Customer Support
http://www.dyson.com
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dyson dc25 retractable wand won't come out


You need to untwist it check out the video belowhttp://www.youtube.com/watch?v=FJcNXrfQDVo ... Dyson DC25 All Floors Bagless Upright Vacuum

Dyson dc25 hose wont come off wand


Tap it all round with the handle of screwdriver to loosen any dust that is stopping it from pressing in. ... Dyson DC25 Animal Bagless Upright Vacuum

Dyson wand won't retract


Hi there,I'm sorry to hear you're having difficulties with your Dyson's wand. Without knowing which model of Dyson you own, I'm unable to provide specific instructions. However, if you visit http: ... Vacuums

Can't get wand to retract - Dyson Ball DC24 Bagless Upright Vacuum


... Dyson Ball DC24 Bagless Upright Vacuum

The extendable wand wont work? - Dyson DC25 All Floors Bagless Upright Vacuum


Throw you dyson away and write nasty messages here because dyson has the worst website for information. for what we pay you should get on-star ... Dyson DC25 All Floors Bagless Upright Vacuum

This is embarassing, but I have just looked at the Dyson DC07 manual and at my Dyson for about 20 minutes, and I can't for the life of me find the wand release button on my actual Dyson.....the manual pictures don't look like the parts on my Dyson....I don't have a hose with a wand release button....the hose just goes straight up inside the handle....Can someone help me? Thanks :)


Hi the wand release button is located directly above the the Cylinder release button. The wand release button looks like the picture below. In order to releease the wand you must firstly make sure the Electrical cable is not wrapped up for storage. S ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dc19 dyson wand holder fault


... Vacuums

My Dyson DC17 has lost suction on the wand and is not picking up dirt as it should. I have taken the small part at bottom of the machine off to see if there is a blockage--none that I can see. The flexible tube on wand is very tight and won't extend very much. Dyson sent me a new cyclonic part in April but the machine still doesn't seem to be working properly. My serial number is 260-us-d11545. Is there somewhere I can take my Dyson to get it fixed. I'm very frustrated with it. Thank you.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson 18 wont stand


Check this video out ... Vacuums

Telescope wont retract into hose


Get a replacement hose witch is fairly hard to fit ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

DYSON DC25 -- CAN NOT REATTACH HOSE TO WAND


... Dyson DC25 Roller Brush Fits The Ball DC 25

The wand is locked in the extended position on my Dyson DC28 and I don't know how to release


... Dyson DC28 Animal Upright Vacuum New DC 28 Animal

Pls Help! My Dyson DC05 (Yellow) needs a new wand. Am unsure whether it is the assembly wand or hand one found in spare parts. The wand I need to replace connects the two long hoses together, and NOT the wand which fits onto pickup head. M.thks if you can advise which one I need. Getty rather dusty in my pad!!


... Dyson DC05 Bagless Canister Cyclonic Vacuum

I have the dyson animal. There is something stuck in the wand tube and everyting is getting caught on it. There is very little suction from the wand. How do I get the wand apart or somehow get the object stuck out of the tube? Thanks


Yes, things stuck in vacuum hoses are not always as easy to remove as one might think. Trying to push it out with something can be counter-productive, and only get the thing stuck tighter! If you have a second vacuum, you can try sucking it out the w ... Vacuums

Hi my dyson dc18 has great suction from wand but when you got to use the vac for floors little suction but wand still got suction even while vacuming floors is it suposed to stop suction from wand


My Dyson dc18 had the same symptoms. The wand worked well and the floor bar had no suction. After removing pieces & shoving my fingers into the machine (no blockage) I found the suction pipe rotates between two positions (floor and wand). It look ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

Wand in stowaway dyson is hard to extend. Seems like u have to pull 3 clips from grooves in 3 rings around wand to extend and shorten wand which is a struggle


Hi there, you should just be able to hold the telescopic wand in one hand, press the button and pull the whole length of the wand out to its fullest position. If the telescopic wand on your particular Dyosn is very stiff, you may need a r ... Dyson "Stowaway" Canister Vacuum Vacuum

Dyson DC 11 Broken Wand Clip


I have the same problem. I contacted Dyson and you have to buy the whole wand assembly ... Vacuums

Vacuum wand won't retract fully into it's compartment.


HI,\015\012FIRSTLY DETACH WAND FROM UNIT AND SLIDE HOSE DOWN AS FAR AS IT GOES, SPRAY A LITTLE WD40 OVER WAND AND SLIDE HOSE UP AND DOWN, AS FOR THE CAP, TAKE A PAIR OF PLIARS, GRAB HOLD OF END OF CAP AND PULL CAP FULLY OUT OF THE HANDLE,AT THI ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Today i was hoovering, and then my dyson just cut out! i left it a few hours then went back to it, it gave a little noise when i switched it on, then again i tried but it failed to come on! ive even changed the fuse in the plug! and now my dyson wont turn on at all, ive cleaned everything there is too clean! help! :D


It looks like you need a professional repair. If you're really lucky this may just be a break in the flex, or the switch has failed - both relatively cheap and simple to sort out. More likely, though, is a problem with the motor (carbon brushes worn ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My dyson exrenable tube wont lock in - Dyson Ball DC24 Bagless Upright Vacuum


Hi there, its Darran at Dyson.Sorry to hear of the problem that you are experiencing with your Dyson vacuum cleaner. If you are having trouble locating the wand handle back inside the hose, it could be that the hose itself is ... Dyson Ball DC24 Bagless Upright Vacuum

Dyson wont turn on and its a bit smelly - Dyson DC07 Bagless Upright Cyclonic Vacuum


It sounds like the motor has overheated and has now been irrepairable damaged. The motor has a built in over-current trip to protect itself (and you if it seriously overheated and caught fire). This normally automatically resets itself, however ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson animal dc 28 wont recline and therefore wont vacuum floors- how to fix?


You DO NOT have to take your machine to a "certified technician" to fix this problem. See the photo above????? Simply slide a thin, flat-head screwdriver down and magically the machine will release. NOW: once it\\'s released, simply examine the area ... Dyson DC28 Animal Bagless Upright Vacuum

Dyson DC17 Animal does not have enough suction from the wand handle to power the mini turbine head. The wand handle has very little suction.


My dyson doesn't have suction either and nothing is blocked. In fact is was working great the vac that is, but when I used the wand for the first time to get the corners the vac shut off, I checked the hoses, filters and all nothing is blocked. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a DC14 Animal Dyson. The wand was sticking, so I figured out the rubber gasket had stretched out. When I trimmed that it worked a lot better, but now the wand is locking up again.


Hi there, its Darran at Dyson.It would be worth contact us so that we can discuss the options available to you. you may need an engineer to visit to replace part of your machine to resolve this, however it may be a part we can send in th ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Hello- My wand has lost a lot of it's suction. I am sure it's clogged somewhere. I cleaned everything after watching a video on U Tube, but it is still not sucking properly. My model is the Dyson DC28 Animal air muscle. I have only had it a few months. Also, I am not having any luck finding a local Dyson repair shop. I live in Pella, IA. Thank you, Kim


You do have a clog ... I feel certain. I have never worked on a Dyson. Please continue with your disassembly until you find that wad of chewing gum and cat hair and tell us how you did it.\015\012\015\012Im sure you will find a clog som ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0544 seconds