Having problems with your Vacuums ?

How do i put the drive pedal back on a kirby ultimate G vacuum?


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do i put the drive pedal back on a kirby ultimate G vacuum?


... Vacuums

The TechDrive Pedal on my Kirby G6 fell out of the back of my vacuum cleaner. I removed the screws from the metal plate one the bottom to try to see if something had come a loose. Can you send me a diagram so I can put it back together or tell me where I can get a service manual. The only part I am having trouble with is the metal piece inside that engages the power drive. Thank you.


The pedal drive fell out . Do you have a manual telling me how to get it together again.. Thanks, Dianne ... Kirby G6 Bagged Upright Vacuum

I have a Series G Kirby Model G7D. The other day when I was vacuuming all of a sudden the TechDrive (Power Drive Assist N/D) pedal fell off. I see the hole that it goes into but when I put it in it's loose and falls out and doesn't control the power drive anymore. When I shook the vacuum I heard something rattling around inside the vacuum head. So I unscrewed the bottom and looked inside and found a small metal part labeled K3 on one side and T on the other side. It looks like it would fit


Hi, I have a Kirby G4 and i'v replaced the carbon brushes myself using a step by step guide however since its been back together it worked for about five minutes it then started sparking from the inside!!(a lot!!) I'v obviously touched something i sh ... Kirby Ultimate G Bagged Upright Vacuum

Hi. This is a Kirby Vacuum model G7D. The Ultimate G series. Have problem with Neutral/ Drive lever on back. Very difficult to operate, very stiff and sometimes impossible to change gears. Torx head s


Manual on how to do it - take a look HERE ENJOY ... Vacuums

I have a kirby sentria. vacuumed up my son's headphones and immediately shut if off. took brush off, unwound headphones, put it back together. when i turned it back on, the belt snapped. so i went to vacuum place, got new belt, but when i put it on, with the green arrows lined up, it doesn't have much suction. with the red arrows lined up, it just smells like its burning and i don't want to break another belt! HELP!!


Take the front off the vacuum and check inside both the front portion and the canister for additonal clogs. Sometimes something will get caught in the impellor, causing the motor to overheat. Since there's little suction and the smell, I'd guess th ... Kirby Generation 3 Bagged Upright Vacuum

It's been awhile since I have used my shampoo system on my Ultimate G series Kirby. Well, as instructed I took it apart and cleaned it. Now I can?t figure out where to put the ?screen cap? and ?sponge filter?. I have my manual in front of me and the only place it shows the filter and sponge (page 35 in the manual) is when it?s been taken apart to clean. It doesn?t show where to put it back. I don?t know what I would do without all the pictures in the Kirby manual. HELP! Thanx. Visual Kirby Vacuu


Hello,\015\012The littlew round screen goes in the hole where the hose attaches to the tank. The round foam filter goes up in the hole underneath the on/off valve for the foam. Here is a guide if you need any more help...\015\012\01 ... Kirby G6 Bagged Upright Vacuum

Kirby G7D neutral drive pedal


... Kirby Ultimate G Bagged Upright Vacuum

How to properly put Kirby Sentria 11 vacuum cleaner back into original box


... Kirby Vacuums

I have a Kirby G4. I have noticed the last few days when trying to vacuum that it is blowing more than it is sucking up. I put on a new bag to make sure it wasn't too full. I also put on the hose and noticed it's not sucking as well as normal. I unzipped the back of the bag holder and noticed the bag isn't inflating as it should be as well. I appreciate any advice. Thank you.


Take the mini emptor off(plastic piece on bottom of cloth bag) this is done by rotating it away from the body of the machine. There is most likely a clog there. Also take the brush head off and inspect fan for chips or cracks this will also reduce su ... Kirby G4 Bagged Upright Vacuum

How do I put my kirby g4 back together - Kirby G4 Bagged Upright Vacuum


Hello, bpI was trying to help you out here. Maybe this will help some? I was going backto some customers that asked questions in the recent past and even fartherback. It appeared that no one answeredsome of them, So, I thought I would take ... Kirby G4 Bagged Upright Vacuum

Kirby drive selector - Kirby Ultimate G Bagged Upright Vacuum


Go here > http://www.goodvac.com/kb_results.asp?ID=16 ... Kirby Ultimate G Bagged Upright Vacuum

My Kirby shampooer - G4 - hardly used any water from the tank and no suds at all. Pet hair did blow out of the small slotted holes in the tray as I moved the shampooer back and forth, but the carpet was basically dry. I did vacuum before shampooing, so the brush part seemed to work great during shampooing, but no water! The small screen was stuck in the crook of the hose that attached to the tank so I did get that out and put it on the small hole on the tank, but it didn't make any difference. I


Few things:Make sure the sponge and the valve under the sponge (water tank) is clean.Make sure you follow the instructions (f you do not have the manual you can find one ... Kirby Ultimate G Bagged Upright Vacuum

Kirby sentria neutral drive pedal fell out - Vacuums


... Vacuums

I have a kirby sentria and after I shampoo'd the carpets I put it back together to be a regular vacuum and now it wont turn on. Any ideas what could be wrong?


The only thing I can think of is the brush head is not on properly.If the head is not aligned right,then the saftey switch wont be activated.Otherwise,I'd say the saftey switch or power switch.Did you make sure not to run over the cord? ... Vacuums

I have a kirby G7D model ultimate g, the diamond edition. i took the brush part off , and used the attachments, i put the brush back on, and now it wont turn on.


Did you happen to hit the N/D switch by accident on the bottom. The switch has to be in D to run. ... Kirby G6 Bagged Upright Vacuum

I need to know how to put my belt back on my kirby 2000 G6 vacuum belt


Greetings from GoVacuum,\015\012\015\012Here's a very informative video that we've recorded explaining in detail how to correctly install the belt on your Kirby Generation vacuum cleaner. I hope this will help you.\015\012\0 ... Kirby G6 Bagged Upright Vacuum

How to put a Kirby Vacuum belt back on New belt seems too short


To put on a kirby belt all you need to do is put on the belt on the brushroll, put the brushroll into the housing making sure the marks on the end of the brushroll are the same. Take the spin dial in the front and "hook" the belt till the dial reads ... Kirby G5 Bagged Upright Vacuum

Drive switch fell off. how do you fix this? - Kirby Ultimate G Bagged Upright Vacuum


Here's a free online guide to help with this problem...\015\012\015\012http://reviews.eba ... Kirby Ultimate G Bagged Upright Vacuum

The right, front wheel on my Kirby Ultimate G won't stay on. It seems to only be held on by friction, and I've hammered it and put plumbers teflon tape to tighten, but it still comes off within 5 minutes of vacuuming. Any solution would be greatly appreciated!


Epoxy! ... Kirby Ultimate G Bagged Upright Vacuum

I have a Kirby G5 vacuum that when light pressure is put on the handle it moves forward but in a jerky movement. Like the drive is engaging and disengaging. If you keep forward pressure on the handle the jerkiness does not happen. Is there an adjustment to correct this.


I hope adjusting position of the position of the "pivot spring assembly" will help. but you may have to disassemble entire slide assembly to clean it up if it still does not work smoothly. See instructions ... Kirby G5 Bagged Upright Vacuum

Gear lever the drive / neutral lever gas come out of the back of my kirby upright diamond edition vacuum cleaner and also the foot on/off power switch is now NOT working either. I am in Maroochydore. Queensland. Australia. 4558


Http://reviews.ebay.com/REPLACING-THE-POWER-SWITCH-ON-ANY-KIRBY-G-SERIES-VACUUM?ugid=10000000003752018 ... Kirby G6 Bagged Upright Vacuum

I disconnected the Kirby vacuum to blow out and clean under my refrigrator, when I put it back it wont come on, don't seem to be getting any electric.


Make sure your electric plug is still in place ... Vacuums

Son took the front plate off the kirby heritage II vacuum thinking that was how to replace the belt, now don't know how to put the three rings and belt catcher back on?


Looked at a kirby vacuum that a family member has and saw how it was assembled! Thank You ... Kirby Heritage II Vacuum

I can't turn the belt off of my Kirby vacuum. I had the front off of it earlier to attach the hose, but now when I put the front back on, I can't get the belt to turn off. The lever twists about 3/4 of the way around, but will not go the rest of the way.


Turn the front part to the green so it is level and then twist the front to the red make sure the belt catch the hook as you twist it then if the belt is hooked just put it back on the vac like normal and lock it in place then twist it back to the gr ... Kirby Ultimate G Bagged Upright Vacuum

How do I replace the drive belt on a kirby G4? Actually the belt is already replaced I just need to know how to reattach that front part back onto the main vacuum. HELP


Greetings from GoVacuum,\015\012\015\012Here's a video we shot showing you in detail how to install a belt properly, and how to reattach the head properly. I hope this helps you;\015\012\015\012 ... Kirby G4 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0881 seconds