Having problems with your Vacuums ?

On my Hoover 6660-900 bagless upright self propelled wind tunnel vacuum when I replaced the cable which works the power drive, there is a spring next to the control arm which I cannot quite figure ou

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

On my Hoover 6660-900 bagless upright self propelled wind tunnel vacuum when I replaced the cable which works the power drive, there is a spring next to the control arm which I cannot quite figure ou

... Vacuums

My Hoover Windtunnel Mach 6.9 brush roller quit working. Upon investigating I found that the idler arm pulley was broken so I managed to replace that. Before putting the cover back on I see the control knob for the roller brush moves a plastic piece left or right to activate/deactivate the brush roller. I don't know where this plastic piece connects. It appears to me that the idler are when raised creates tension on the belt which drives the roller. I'm at a loss trying to figure ou

Try this link belowhttp://www.ereplacementparts.com/hoover-u6630900-windtunnel-selfpropelled-bagless- ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Elna 7200. The bobbin spring seems to have come loose, but cannot figure out how to get it in place again, so we cannot work, Pls help.

The best course of action in your case is to take sewing machine center and let them show you how to get it in place. They may even help for free because you might become a potential costumer. I hope that there is a repair center near you. ... Vacuums

I have a GE model #SCA1000HBB02. Recently the control buttons quit working. I thought maybe someone locked the controls but thats not the case. The display lights up shows the time but thats all. I unplugged it and then powered it back up the display comes up to set the time but the buttons will not allow. Any help would be appreciated. Thanks, Gary

Sorry but this is the vacuum area, your problem maybe the main board or a fuse. please go to the microwave forum. ... Vacuums

Roomba Schedular I have a Roomba Scheduler and it has worked great until recently. Suddenly it quit working. When it is charging the power light goes from red to green as it should, showing it is ready to use. When we turn it on to use, it will only go on for a few seconds then it shuts off like it is out of power. It is like it isn't really charged. Is there something I can try to make it work?

Let it charge for a full 24, or even 48 hours, regardless of the green light. If it still dies you probably need a new battery.. or worse. ... Roomba Robotic Floor Bagless Vacuum

Where can I order the following parts for my 1952 KENMORE SEWING MACHINE MODEL #117583, SERIAL #48054: : #5107 carbon motor brush (2) #5110 motor brush spring (2) #5111 motor brush spring cap (2) String for starter control lever Pulleys, screw and nut washer to attach string control Best sewing machine ever and still working like new, and I want to keep it that way. Thanks.

... Vacuums

Hover F7452-900 My brushes are not turning. I have taken the tanks off to check the switch that changes from carpet to hard terrain to Ceramic tile.I noticed that there is a spring that has came off. I tried to disassemble the top half (nose) of the cleaner but I have came to a stand still. I cannot figure out how to remove the cover so I can figure out where the spring should be attached. I have removed all the screws that are visible and it still won't budge. It is loose but on the back side o

Regarding the brushes not turning:\015\012\015\012Your filter may need to be cleaned. It is located behind your brushes. With your tanks removed and the cleaner unplugged; tilt your cleaner back. The filter screen located behind your b ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Attachment problem used a new unit w/attachment for 5 minutes...dispensed solution in a powerful triangular fashion. Then the fluid quit dispensing out of the attachment nozle amost like the pump quit working. Primed the unit several times w/ no success. checked for clogs. can't tell if the floor portion is "pumping' or just dribbling solution onto the floor with the trigger. can see no leaks at this point. unit worked for about 5 minutes on apholstery

Make sure everything is filled and secured tightly, if this a new unit it should be something simple ok, also check where machine folds down that the solution hose is not being pinched its right behind the dirty water tank ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

REMOTE CONTROL IS MALFUNCTIONING & NOT TURNING ON CUSHION - Hello. I bought a used (by near new) Shiatsu+ Massaging Cushion from Ebay. When I installed it today the remote control was faulty. When you push the Power button, the blue light comes on, but none of the other buttons work. When you push the Power button again to turn it off, it clicks & turns itself back on again. So it's running but nothing is happening in the massage cushion. I did see a card in the box saying "For the Shiatsu

Before you use this cushion you MUST first 'unlock' the rollers which are held in place by a screw which MUST be removed or the unit will self destruct. The manufacturer provides a hex wrench to remove the shipping screw and a large label on th ... Vacuums

I have a Series G Kirby Model G7D. The other day when I was vacuuming all of a sudden the TechDrive (Power Drive Assist N/D) pedal fell off. I see the hole that it goes into but when I put it in it's loose and falls out and doesn't control the power drive anymore. When I shook the vacuum I heard something rattling around inside the vacuum head. So I unscrewed the bottom and looked inside and found a small metal part labeled K3 on one side and T on the other side. It looks like it would fit

Hi, I have a Kirby G4 and i'v replaced the carbon brushes myself using a step by step guide however since its been back together it worked for about five minutes it then started sparking from the inside!!(a lot!!) I'v obviously touched something i sh ... Kirby Ultimate G Bagged Upright Vacuum

Hooked everything up per directions. I plugged it in to the closest electrical outlet and nothing happened. The lights did not light up, the connected wall control and sensors leds do not light up. It appears the unit doesn't have power. The electrical outlet socket is fine as everything else I plug into it works fine. I have tried every other electrical outlet available. The unit won't power on from any outlet, and all of those outlets run other things, like power tools an refrigerators

Dear Davehibshman,Firstly; dismantle the plug and replace the fuse with the same rating as the one you have just taken out. Replace the plug cover, put the plug into the socket and try again. If this doesnt work, there may be a problem wi ... Vacuums

Power nozzle has quit working

Most of these nozzles have a reset button on them. Standing behind the nozzle it is on the back, right side. ... Filter Queen Majestic Canister Vacuum

We have the Kenmore progressive direct drive (bagless) and have had it for about 3 years. We have taken good care of it, and paid quite a bit for it hoping that it would last for a good long time. It has started making a noise that seems to be an overflow air type of noise coming out of a bottom air outlet opening for when the air flow is blocked. We have looked into clogs, changed filters, and the whole works, to no avail! Quite Frustrating since I love this purple vacuum! The machine started

There has to be a clog or block somewhere - if the motor works, it should work did you try a wire coat hanger to go up in further where you cannot see?Bets regardsCk ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

The Dyson Animal won't turn on or off. The red power button doesn't control the on/off for this machine any longer. Once plugged in, the vacuum will work and the power cord must be unplugged to turn it off. Any help would be appreciated.

The machine needs a new switch. The switch is stuck to the "on" position. ... Dyson DC05 Bagless Canister Cyclonic Vacuum

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i

At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

I just purchased this product and used the Turbobrush on 1 chair and it stopped working already. I have gone through my instructions very closely and I cannot figure out why it now will not work. Help!

It seems to be time to take the machine back to where it was purchased for warranty repair or replacement. Good luck! ... Bissell 1425 Little Green ProHeat Handheld Steam Vacuum

Does power drive wheels work both in forward and reverse and if they dont what is the solution? mine seems to work only in reverse??

The drive transmission works in both directions. If they do not, then the metal cable connection (under the hood) that connects the handlle grip to the transmission, may be slightly out of center adjustment. ... Hoover U6311-930 Power Drive Bagged Upright Vacuum

I have taken delivery of a new Lloytron Halogen Oven E4701 WH.from a supplier in the UK (I live in Spain). On unpacking it I found that Part of the temperature control knob assembly had fallen down inside of the heater body. I dismantled the heater body to retrieve the part but I cannot now work out the order of re-assembling the fan parts so that the fan does not catch on other parts of the assembly. I cannot find a parts drawing on-line. Can you help ?

... Vacuums

My Vacuum DC-17 has just quit sucking. It has been making quite a racket since I had the belt changed at a repair shop several months ago. I was told that the belt was a new design and figured that was why it was making so much noise. it seemed to work fine, was picking up dirt and all, but today, when I started vacumming, I noticed it was not sucking air either with the belt engaged or not. My vacuum is approx. 5 years old.

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My Sebo X1 stopped working and my husband tested it and determined that the on off switch was not working. I purchased a replacement switch online but I cannot figure out how to remove the old switch. Please can you help?

Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Sebo Automatic X1 Bagged Upright Vacuum

The brushed roller on my Hoover Upright Canister has quit turning. Is this a broken belt? A friend recommended a "reset" button--is there such a thing?? Everything else works fine; power, suction, headlight. That belt just doesn't work anymore since we accidentally caugght the edge of a throw rug.

Belt. There is no reset on this model. ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa

... Electrolux Vacuums

My Oreck XL has worked very well until the power cord was pulled out of it. I figured how to hook up the hot but can not figure out the neutral connection. any ideas?

If there are two wires it doesnt matter normally white 2 white and black 2 black if its 3 wire than green is ground and the other 2 dont matter thanks Don ... Oreck XL Ultra Bagged Upright Vacuum

My Sebo X1 stopped working and my husband tested it and determined that the on off switch was not working. I purchased a replacement switch online but I cannot figure out how to remove the old switch. Please can you help?

Www.manualnguide.com/manual/sebo-x1-repair/page/3/\015\012\015\012Above is your user manual, and below is an exploded diagram so you can see where it all goes. Find all the screws lock ... Sebo Automatic X1 Bagged Upright Vacuum

KitchenAid slide out Exaust fan Mod# KWVU265YBA-O Would not work (lite,fan) every once in awhile, now quit working all together.Could it be the micro board or is it the touch button control?

I would first start out by cleaning the touch pad from all the oily smoke residue over time,these membranes get dirty and the smoke residue insulates the connections on the switches and back side of board,then if possible bypass the module and see if ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1118 seconds