Having problems with your Vacuums ?

Does not **** up anything

\015 Work the first two time does not **** anything up\015

Answers :

Your vacuum is clogged. turn upside down so you can see the spinning brush. take a philips screwdriver and remove the screws holding the bottom plastic cover on. remove the spinning brush. take a wire or piece of hanger and fish out all the junk stuck in the vacuum tube.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Model number f 5912-900 hoover steam vav with clean surge.This is not the f5914 model........my new machine has 10 min. on it...in mid use it has stopped sucking and now is blowing more than anything, I took the front clear piece off as well as the black cowling/shroud and can find no obvious hoses to un-clog nor anything else to un-clog for that matter...I am looking for advise to fix this thing now, myself


Here is a list to go by for no suction problems that you can follow along with they are common proble\015\012Problem #1 Steamvac is not Sucking!If your Hoover Steamvac was working properly and suddenly it is not sucking any ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My dyson animal vacum hose no longer wants to **** up anything i have removed the botttom part that u can unscrew and removed somethings that were stuck in there since then it no longer picks up anything any suggestions


Check all connections and motor ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hello i own the bissle proheat steamer it turns on but no water or soap or suction from floor or the utensiles ive taken the take off the back to scope out anything that could be in the way but dont see anything the motor is making that clogged vacume noise witch makes me believe something could be stuck somewhere in it but it could also be no water is getting to the pump or despencer but the brissels still work belt for that is good where would i be best to check and where is the location of th


... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Producing steam i just got the shark assembled the mv2010, then it is not doing anything, it vacuumed just fine, but when i put the steam pad on it wouldnt ever produce steam or do anything,it felt like the water was heating up but even after it sat for 20-30 minutes when i pull handle back towards me nothing happens, no lights no steam no nothing, so why wont it work


This link is for the manualhttp://www.sharkclean.com/manual/MV2010_11_IB_ENG_110103.pdf ... Shark MV2010 Vac-Then-Steam 2-in-1 Vacuum and Steam Mop Purple

Our shredder (Wilson Jones 1200) now has a very high pitched squeak when we shred anything. Really high pitched. We can't see if there's anything stuck (ie a staple) Is there a number we can call for servicing? Thank you, Emily Hynes 902 424-1002 RBC Dominion Securities Inc, Halifax NS


... Vacuums

My filter queen just had the motor rebuilt last year and was basically a brand new unit when I got it back. It is not picking anything up now when I vacuum. The beater bar on the carpet attachment is turning fine and when I take all the attachments off the hose I can feel the suction being created like it should be picking up debris just fine. I have emptied the canister even when it did not have much in it; however, it still will not pick anything up off the carpet. It picks up debris tempo


It sounds as if you have a clog inside the "Power Nozzel". They mention that there are "no user serviceable parts within the Majestic® Power Nozzle" My advice would be to see if you can see a clog with in reachable distance and try to remove the ... Filter Queen Vacuums

Hello, I have the same model. And though it is three years old, starting from the last month, it does not clean anything anymore. Cannot even pick up one single thing from the floor. Every dirt gets stuck in the hose. I cleaned the hose and cleaned the filters but it still does not pick anything up. Is three years its normal lifetime or do I have the change the filters, instead of cleaning them? Thanks.


I know bissell vacuums are very cheap but they should last more than 3 years. there should be two parts to the dirt cup. remove the dirt cup and above it there should be a round plastic part. unscrew it and check that filter. ... Bissell 6594 PowerForce Bagless Upright Vacuum

I have a dyson dc21. All the sudden the hose is hardly suctioning up anything. If I take the canaster off, the top air hole suctions extrememly well, but when I place that canister back on, the suction is not going thru the hose and picking anything up. I have squeezed the hose, I feel no air leaking and do not feel any blockages...what could be wrong. It worked fine the other day and today, it won't pick up a piece of lint!


... Dyson DC21 All Floors Stowaway HEPA Bagless Canister Vacuum - Iron/Titanium/Yellow

Rollar is not turning. Belt seems to have tension. Does not **** anything up off of the floor. Filters are clean but when we turn it on, the roller is not turning or sucking anything up off the floor.


Hi Susan,I'm sorry to hear you're having difficulties with your DC07. It's probably best if you get in touch with us directly so we can determine which model of DC07 you have, and run through some troubleshooting over the phone with you. You ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Isn't picking up anything. it runs and the brushes run, but it's not picking up anything


Its loosing suction. most likely a clog ... iRobot Roomba 530 Robotic Vacuum

Oreck XL21 just will not work at all any more. Beater is clean - belt is fine. Fresh bag - inflates. Took the thing apart - checked for blockages at intake, bag entry, and the tube. It just doesn't vacuum anything. No suction at all for anything stronger than air. I'd say it doesn't ****, but that would be ironic. Are these known for just "quitting" after a while? We take it in for maintenance as recommended to replace filters, etc. Is there some miracle trick to make it work or sho


Did you make sure the brush turns freely? Even though it is clean, if it does not turn freely with the belt, it will not beat the carpet and pull debris up into the unit.\015\012\015\012Another (drastic?) thing to try would be to take the unit ... Vacuums

My kirby sentra won't **** up anything. I've changed heads and bags to see if something was stuck inside but couldn't find anything.


Your inferance proves that the fault could be with the vacuum pump. Since the rest has been checked and there is a drastic reduction of the suction rate of the pump, I think the motor must be checked. Please remove to see if there is accumulation of ... Kirby G6 Bagged Upright Vacuum

No "sucking" action i'm not getting any air to **** up anything, i cleaned it up put new belt on, doesn't look like there are any obstructions can't get it to **** up anything


Did you check to see if the beater brush was rotating properly?\015\012When it doesn't it usually causes the belt to burn and break, though I do not believe you had a belt issue.\015\012\015\012If you remove the beater brush like you did to rep ... Hoover Tempo Widepath Upright Vacuum - Blue

The brush on my bissell prolite multicyclonic vacuum won't turn. It seems like it is jammed, but I checked for anything that might be stuck in it and don't see anything. Is there a reset button?


I had the same problem with my old Bissell sweeper ( I bought a new rotating brush each time this happened then I bought a new sweeper the next time it happened -last Dec. 2009.) Unfortumately I bought a new Bissell and now it is happening again to ... Bissell 17G5 PROlite MultiCyclonic Bagless Upright Vacuum Cleaner

Spare wire? My SEBO X4 flex had to have the fex shortened because the cable sheathing had come out of the internal gripper and there was a couple of inches of two strand wire hanging out the cable entry point before the insulation sheathing started. No problem doing this but on the live switch terminal there was a piggy back spade connector. The second wire from this went down inside the handle and just ended with a bare terminal hanging in space. It hadn't come off anything, there wasn't anyth


Greetings from GoVacuum.com,I took a picture of the Sebo X4 wiring in the handle of the machine for you. This is a brand new machine taken out of the box, this is how the wiring should look. You'll see that there are 5 total wires here. ... Sebo Automatic X1 Bagged Upright Vacuum

Dyson hi my dyson sounds as if something is catching when the brush goes round, it's very loud, it still has good suction. I have taken the plate of can't see anything or fell if there is anything obstructing the brush, could it be the belt?


Hi.\015\012If the brush turns freely then you will need A new clutch unit fitted to your machine.\015\012There are loads of them on Ebay very reasonabley priced only buy new not second hand.\015\012\015\012Manuals are availabl ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

I have an Electrolux LITE upright carpet cleaner - about 15 years old. Suddenly last night when using it, from the normal motor (whooshing) sound, the motor suddenly went very slow and with a slight grinding sound. The brushes are now just turning round very slowly and areobviously not picking up anything. Has the motor gone or is this repairable, or should I just get a new cleaner? I have tried to open the machine from the bottom to see if anything is obviously wrong, but it looks complicated a


... Electrolux Vacuums

The brush stopped revolving. I don't see anything blocking. It sucked up a corner of a rug for a split second but didn't pull anything off of the rug, ie, nothing from the rug is in there. Do these have belts? I don't see that. vicki


Although I do not share the exact same model that you have, there is a belt in the one I own. \015\012\015\012Checking it was pretty easy as the unit comes apart in a simple manner.\015\012\015\012I do not know how your unit comes apart b ... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum

IRobot stopped picking up larger bits from the carpet. It picks up the dust, but anything larger, it leaves behind. Have changed the filter/brushes. Is there anything else I need to do


Its sounds like the brushes aren't turning. Pull the vacuum and bin off the back and start it and look to see if the brushes are turning. ... iRobot Roomba 560 Robotic Vacuum

My hoover windtunnel is not picking anything up all of a sudden. Also the roller underneith is not spinning. I've replaced filters and the attachment part is working fine, just when it's in the upright position it won't pick anything up. It also doesn't seem to be self propelled anylonger either. It use to **** everything up, including the dog. Please help!


The belt that drives the brush roll has broken. That's why it doesn't pick up and why it doesn't pull itself forwards. Check the User Manual (download from Hoover website if necessary) for information on replacing the belt. Good luck! ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

No suction. I have followed the detachable parts no suction. I have followed the detachable parts and it seems to have suction through to the base but doesn't pick up anything significant. I have looked through the hose connecting the base but I can not see anything obstructing it.


Poor suction can be caused by obstructions, poor air flow or a compomise in the air flow (hole in the hose). Since you have started with that I would next look at all filters and clean them. First check for suction at the motor, then at accessory hos ... Vacuums

Absolutely no power. No light or anything. Is


There's a small white button on the back of the machine near the left wheel. Use a paper clip or similar item to push that in. ... Riccar 8955 Upright Vacuum

Hi, No air and not sucking anything up


Toss the motor and and sell the other parts on ebay. BUY A NEW ONE ... Kenmore Vacuums

Have eureka 9734 replaced belt, put back together,brush rotates well but vacuum is not picking up anything, no suction.


It sounds like the machine is clogged. Check the port behind the belt and any and all hoses for obstructions and remove. ... Vacuums

Eureka, whirlwind 12 amp vacuum does not pick up anything


That problem can be caused by the belt being stretched out and even though it is spinning when you look at it, with the resistance of the carpet it will stop.With a model number I could tell you exactly how to change the belt, but most of ... Eureka Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0196 seconds