Having problems with your Vacuums ?

How do I take apart to clean my hoover spin scrub shampooer?


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I take apart to clean my hoover spin scrub shampooer?


... Vacuums

I have a hoover f5914-900 steam vac.. and I was wondering if there's a way to take apart the spin brushes to get them cleaned out well. I loaned it to family, and the brushes came back extremely soiled and not spinning.


The brush block may be removed from the base for rinsing.\015\012Yes, you can CAREFULLY disassemble the brush block assembly by releasing each of three latches that hold each of the clear gear covers to the main block. A small screwdriver is u ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My Hoover Steam Vac Spin Scrub aw/ Clean Surge


Greetings,\015\012\015\012A few more things that you can try on your SteamVac. First remove the dirty water solution tank from the machine completely. You should see where the solution tank was just sitting, a plastic casing with a wh ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My Hoover Steam Vac Spin Scrub aw/ Clean Surge


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Have Hoover F7452900 spin vac carpet shampooer and brushes won't spin. The screen by the brushes is clean and they are place in position to clean on carpet. I noticed that when I have the brushes out of the machine and turn it on that the white square that is on the base of the machine does not spin--this is where part of the brush connector fastens to make bristles spin.


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover F5809 Hello, I seen a few of your post and was hoping you could help me. I just became a member today. My sister gave me her old Hoover Steam Vac-Model F5809. This thing is so dirty and clogged because my sister has pets. So far I've gotten it all taken apart to clean it. I'm not a newbie and taking apart and fixing things. I have fixed things like microwaves, washers, dryers, dishwashers (still learning about TV's-very hard, hehe). Anyway, I got what I believe to be the motor cover off.


That cover is the called the fan cover and is usually pressed on. Tapping on the edge with a flat blade, you may be able to get it off and hope you don't bend it up, you will to put it back on tight enough so it will stay in place. Another thing to ... Vacuums

How do I take the top off my hoover spinvac shampooer


1) test the motor outside from the machine, carefully and do not touch any side live wire.2( see the diagram simple for help and test the motor, otherwise you must go to the repair shop motor.God bless you ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o


Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My hoover spin scrub brushes stopped spinning and i have cleaned intake filter and tried to turn the thing that spins it...when brushes are off the hole turns then as soon as i connect brushes the brushes will not turn what else can i do!!???


... Vacuums

Hoover spin scrub clean water dispensing tank. How do I replace the spring, seal and valve stem at bottom of clean water tank?


... Hoover SteamVac SpinScrub 50 Carpet Washer with Hard Floor Tool and Accessories

I have a Hoover, Steam spin scrub, Model F5897-900. Only used it a couple times and the motor gave out. First started being noisy then a bad smell. It did seem noisier that what I would expect from the start but I didn't realize it was a problem with the shaft of the motor. I took it apart and found the motor shaft wasn't true and causing sparks. The motor looks like it can not be taken apart and repaired. This seems like a default from the beginning but it is past warranty. Also noti


You will have to replace the motor and the hose asm. thehooverstore.com may be able to help, or you should be able to find a repair shop that can order them for you. ... Vacuums

My vax power 8, 2200 watts 300 air watts 4L capacity upright Hoover is brand new, I emptied out the dust/dirt collecter and cleaned the motor filter yesterday for the first time, i switched it on and all fine, the brush is spinning and the hose is sucking, put the Hoover to work it's fine for about 30 seconds then then suction stops and its dead it won't collect no more, so switched off taken apart again and the motor filter is blocked and full of dust, so I unblocked it, do the same process aga


I had the same problem. It looks like the seal on the lid on the bottom of the cylinder has fallen out when it was emptied. There is no longer a proper vacuum being created so you don't get the cyclone effect and the dirt doesn't collect where its su ... Vacuums

Can't find info for hoover steam vac spin scrub model # F5905900 on Hoover website, doesn't show that model number at all...looking for mesh (kind of cone/cylinder shape) that goes in dirty water tank (I think) and also the tool (wand) that slides into front to clean it out. It doesn't pull all the water up very well and the filter has been missing for some time. I don't know if that has anything to do with it or not. As far as the wand tool goes, I have taken the cover off at this point and


The cleanout tool is part # 43514001. The filter is # 90001398. Be sure to leave a 1/2 inch gap between the top of the filter and the bottom of the lid. If you need a manual, try model F5914-900 0r F5912-900 on Hoover.com ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover filter Since I cleaned the filters the dirt collects there instead of falling into the reservoir. I've tried taking apart and reassembling them, but the problem stays. I'm having to clean the filters every time I use it. Any ideas?


... Vacuums

My Hoover Steam vac has also stopped sucking... I have pulled it apart to clean it. Is there a way to take the bristles off to clean them as well as are there any other parts that could be the problem?


Based on your description, poor suction is related to only a few things\015\012\015\012Check filter inside lower tank\015\012Check the lower tank lid to be on properly\015\012 ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover steam vac spin scrub leaking cleaning solution


The hose leading from the tank to the sprayer head on the bottom of the unit, or the tank is not seated properly or the tank has a hole or crack ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Is it possible to take the Hoover Brush Block Assembly F7220-900 #48437029 apart so that I can thoroughly clean inside the block? It looks like it could, but I don't want to break it by trying.


... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

How do i take the filter apart to clean it - Hoover U6630-900 WindTunnel Bagless Upright Vacuum


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a Hoover Steam Vac All Terran floor shampooer, I have taken apart the brushes and other parts to make sure there are no clogs, but it still is not spinning. What else can I do? the Motor is working fine. and the suction is fine too.


There may be some substances such as dust or sand stuck in the spinning parts of the wheel. The substances are restricting the mechanism to work properly and causing blockage in the rotating causing your problem. Cleaning every part of the motor's ro ... Vacuums

I have an older model F6056-900 Hoover steamvac Spin Scrub Cleaner. My first problem was that I loaned it out to a friend. Anyway she ran over the hose (used for attachments) with her car. I tried using the cleaner for carpet cleaning this morning but when I tried to put the solution tank into place...its loose...won't snap back in like it used to. When I can get it somewhat in place the solution just complete drains out through the bottom fo the tank. The leak is where the small hole on the bot


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My Hoover Spin Scrub leaks when I take it to the kitchen to dump the water. I leave a trail. Also, there is a lot of water under the machine when I remove the water tanks. ??


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hello, I have Kenmore Vacuum Cleaner Model 116, serial # DH1037491. The brush roll does not spin. I do not know how to take it apart and clean. I will appreciate very much any advice. Thanks in advance


... Kenmore 33721 Upright Vacuum

I have a Hoover SteamVac, Model F5906-900 and the brushes won't spin. It's like something is froze up inside. I have read where the Brush Turbine might need to be replaced. Can you tell me where I can find the schematics or an internal diagram of this model so that I can take it apart. Or maybe you might have another suggestion. Thank you Pauline Newman


\015\012Hello,\015\012\015\012This is most likely the reason the for the brushes stop spinning. I've written a very detailed repair guide on how to diagnosis this problem. This will walk you through step by step with pictures, an ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Suction button Although my Hoover Spin scrub is working perfecting dispensing the solution, when I go to suck up the solution from the carpet--I am having problems with the RED suction button that keeps popping up. I have to stop the cleaner and lift up the dirty water container to break the suction. Ive tried cleaning the netting that is encased around it, but still no luck. Any help would be appreciated! Thanks


This happens when the filter on the inside of the lid for the dirty water tank is pushed all of the way up. You need to leave a 1/4 in. gap from the top to the top of the filter ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My hoover vacuum runs for about 10-15 minutes then the saftey feature shuts it off(overheat?). i have taking it apart a cleaned it with no results, added new bag also. after an hour it cools down and works again. do i just need a new vacuum?


Do you have suction through the tools? Does it look like it picks up when it runs? The machine could be clogged and that would cause the problem, but unfortunately the sensor that shuts the machine off could be bad if the machine isnt clogged. Its no ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1103 seconds