Having problems with your Vacuums ?

Turbine head for dyson d23 had stopped turning

\015 Bar on turbine head stopped turning\015

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Turbine head for dyson d23 had stopped turning

... Vacuums

I have a dyson DC23 and the turbine head will not turn anymore can anyone help on how to reset. I have cleaned it and there is no blokage its just stopped? Please can someone help

Pull the plunger into the ''out'' position for vacuuming carpets.For vacuuming hard floors push the plunger into the ''in'' position to stop the brushbar spinning.Refit the tool onto the ma ... Dyson DC23 Bagless Canister Cyclonic Vacuum

Our dyson absolute turbo head has stopped turning. I caught the edge of the mat in the head, I turned it off straight away. It won't go around.

It might have broken the belt. Here is a link for the\015\012instructions on how to change the belt and a link for the belt you need:DC07 Belt Changing Instructions ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Dyson D23 Vacuum just stopped and it won't turn on no noise nothing stopped completely now what any suggestions?

... Dyson DC23 Bagless Canister Cyclonic Vacuum


... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Turbine head brush bar not turning - Dyson DC23ACTUSC Bagless Canister Cyclonic Vacuum

... Dyson DC23ACTUSC Bagless Canister Cyclonic Vacuum

My DC 26 turbine head keeps stopping - Dyson DC25 All Floors Bagless Upright Vacuum

... Dyson DC25 All Floors Bagless Upright Vacuum

Brush head stops turning once hoovering - Dyson DC35 Handheld Vacuum

... Dyson DC35 Handheld Vacuum

Dc25 turbine head stopped working

... Dyson DC25 All Floors Bagless Upright Vacuum

I have a Dyson dc 20. turbine head not working(not the

... Vacuums

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.

The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

I have a dyson canniter stow away vacuum. i've had it for 2 years and it just started having a problem. when i turn it on the motor starts just fine but the vacuum head does not turn on. Yet when i push it forward it trys to start and turns on for a second and turn off - almost like the connector isn't connecting the hose to the head very well anymore.

Hi, After reading you're problem, the symptom's are just like you said. Its just a matter of checking the connections. The connection where it plugs into the head it self. When you push forward the forward motion and down pressure makes ... Dyson "Stowaway" Canister Vacuum Vacuum

I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos

It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum

Dc11 dyson the brush head turns very slowly but when i take brush head cover of (the yellow part) and put my hand over the suction inlet part the brush head turns really fast. Have cleaned out collection chambers eg the hoover bag have washed the sponge with the little pictures of taps on it what now . thanks alan

I have taken the brush heads off and pulled all the hair out of the small gap between the chrome shaft and the plastic gear housing. Then a small amount of 3-in-1 oil into that gap to lube the internals and just a little through the air intake on th ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

When the power head is turned on it goes from green light to red light and stops. The belt is fine and there is no obstructions in the brush to stop it from turning.

This will happen only when the brush or motor does not turn the right speed \015\012make sure to pull the end caps off the brush and clean any hairs or fibers from it\015\012the motor you can try and turn it by hand with out the belt on a ... Fantom Vacums Lighting Canister Vacuum

The brush bar on my Dyson DC17 stopped turning.

If this model has a brush control - i.e a roller at the side of the model which controls brush to spin or not, then its a protected brush model - therefore even if the drive belt is intact the Dyson would have to be repaired by a service personnel or ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Is it possible to disassemble a Dyson floor tool/head please? (Not the turbine head!-the duel floor head!)

Take the head off then take to the nearest garage and use there vac to **** it out or the blow it out with there compressor. ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Turbine head of my Dyson DC08 does not spin

This response is likely too late coming, however for others the problen appears to be the same as the fault with my turbine head which was that the turbine fan had become loose on its spindle. With no pressure on the brushes, friction would allow the ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

My Dyson Animal turns the "flipper"(?) on that I would use on my carpet, but it turns stops turning right away. It then goes on and off every 5 seconds or so.

You need to replace the belt that turns the brush. Here is the belt you need and a manual with instructions on how to change it:Dyson DC07 Belt and Manu ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.

... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?

Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The beater bar on my Dyson won't turn. The vacuum runs and suctions but the bar won't turn and the belt is not broke. The beater bar did get a carpet fiber caught and wrapped around it which stopped the bar and I removed the bar to cut the fiber loose and replaced it and now it won't turn

The belt doesn't have to be broken to make the vacuum not work correctly. If the belt is stretched the vacuum won't operate the way it is supposed to. You can get replacement Dyson Belts here: ... Vacuums

Turbine head Dyson DC39 The turbine does no stay on consistently

... Dyson DC39 Animal canister vacuum cleaner

The beater bar on my dyson DC28 is not turning when it is placed on the carpet. If you lift the sweeper up the beater bar will turn but then when you place it back down on the floor it stops.

... Dyson DC28 Animal Bagless Upright Vacuum

We have a Dyson stowaway DC20 Turbine and the turbine head is not spinning at all.Can you please advise if this can be fixed and how. Thankyou from, Bev Effern 0411 018 531

Are the pins at the connection between the wand and head damaged? Has the turbine been verified that there is not blockage? ... Dyson Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0809 seconds